2 layers33.4 × 29.2 mm
2 layers61 × 39.7 mm
Arduino taller
MakerAlc/tallerpcb2Repositorio de taller de pcb
- Size
- 61 × 39.7 mm
- Copper layers
- 2
- Thickness
- 1.6 mm
- Parts
- 37
- Nets
- 37
- Pads
- 147
- Tracks, vias
- 372, 59
- Pours
- 2
- Routed
- Yes
- KiCad
- KiCad 5 (file 20171130)
- Created
- 20 Nov 2020
- Updated
- 22 Jun 2022
Overview
Arduino taller is an open-source printed circuit board by MakerAlc, from the MakerAlc/tallerpcb repository on GitHub. It is a 2-layer board of 61 × 39.7 mm with 37 parts on 37 nets, routed with 372 tracks and 59 vias.
It is built around the ATMEGA328P-AU and MIC5239YM. Its parts include 14 capacitors, 9 resistors, 3 connectors, 2 ICs and 2 diodes. It belongs with the AVR (ATmega, ATtiny) boards of this library.
Main components
2
ATMEGA328P-AU
TQFP-32(7x7)-40℃~+85℃ 1.8V~5.5V 10bit 1KB 20MHz 23 2KB 32KB 8 Bit AVR Built-in FLASH TQFP-32(7x7) Microcontrollers (MCU/MPU/SOC) ROHSMicrochip TechnologyMicrocontrollers (MCU/MPU/SOC)
MIC5239YM
SOIC-8-40℃~+125℃ 1 1.24V~20V 160uVrms 30V 350mV@(500mA) 45uA 500mA Adjustable Over Voltage Protection Positive SOIC-8 Voltage Regulators - Linear, Low Drop Out (LDO) Regulators ROHSMicrochip TechnologyVoltage Regulators - Linear, Low Drop Out (LDO) Regulators
README
PCB_Propuesto_Arduino/README.mdTaller_PCB_MakerAlc
Taller de iniciación a los PCBs
Parts
37| Qty | Value | Footprint | References |
|---|---|---|---|
| 6 | 100 nF | Capacitor_SMD:C_0603_1608Metric_Pad1.08x0.95mm_HandSolder | C2, C3, C4, C6, C9, C11 |
| 5 | 1k | Resistor_SMD:R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R3, R4, R5, R8, R9 |
| 4 | 10 uF | Capacitor_SMD:C_1206_3216Metric_Pad1.33x1.80mm_HandSolder | C1, C5, C13, C14 |
| 2 | 16 pF | Capacitor_SMD:C_0603_1608Metric_Pad1.08x0.95mm_HandSolder | C7, C8 |
| 2 | 4k7 | Resistor_SMD:R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R1, R2 |
| 2 | LED | LED_SMD:LED_0805_2012Metric_Pad1.15x1.40mm_HandSolder | LED1, ON |
| 1 | logo:makeralc_20.3_20.3_mm | ||
| 1 | 10 nF | Capacitor_SMD:C_0603_1608Metric_Pad1.08x0.95mm_HandSolder | C10 |
| 1 | 100 | Resistor_SMD:R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R7 |
| 1 | 10k | Resistor_SMD:R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R6 |
| 1 | 8 MHz | Crystal:Crystal_SMD_5032-2Pin_5.0x3.2mm_HandSoldering | Y1 |
| 1 | ATmega328P-AU | Package_QFP:TQFP-32_7x7mm_P0.8mm | U1 |
| 1 | AVR-ISP-6 | Connector_PinHeader_2.54mm:PinHeader_2x03_P2.54mm_Vertical | ISP |
| 1 | Conn_01x18 | Connector_PinHeader_2.54mm:PinHeader_1x18_P2.54mm_Vertical | J1 |
| 1 | Conn_01x23 | Connector_PinHeader_2.54mm:PinHeader_1x23_P2.54mm_Vertical | J2 |
| 1 | DNP | Capacitor_SMD:CP_Elec_5x5.4 | C12 |
| 1 | FTDI Basic | Connector_PinHeader_2.54mm:PinHeader_1x06_P2.54mm_Vertical | Serie |
| 1 | Ferrite_Bead_Small | Resistor_SMD:R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | FB1 |
| 1 | MIC5239 | Package_TO_SOT_SMD:SOT-223-3_TabPin2 | U2 |
| 1 | SW_Push | Button_Switch_SMD:SW_SPST_EVQPE1 | Reset |
| 1 | Screw_Terminal_01x02 | TerminalBlock_4Ucon:TerminalBlock_4Ucon_1x02_P3.50mm_Vertical | J5 |
The 36 most common of 37 parts.
More from MakerAlc/tallerpcb
1Similar boards
- 2 layers80 × 110 mm
NucDeck Left Controller PCB
dmcke5/NucDeck
The Open Source DIY Handheld Gaming PC!
59 parts561CERN-OHL-S-2.0 - 2 layers50.5 × 128.5 mm
- 2 layers152 × 88 mm
RFBitBangSMT
profdc9/RFBitBanger
A QRP digital transceiver created from readily available parts for off-the-grid maintenance
271 parts222 - 2 layers50.2 × 31.2 mm
MCU Datalogger
futureshocked/KLP4e_MCU-Datalogger
This is the repository for the "MCU Datalogger" project.
31 parts138MIT - 2 layers34 × 46 mm
- 2 layers73 × 94 mm
Sportiduino base
sportiduino/sportiduino
Electronic timing system for orienteering and similar outdoor sports events on Arduino
119 parts78GPL-3.0 - 2 layers58.9 × 44.2 mm
OpenPSX2AmigaPadAdapter
SukkoPera/OpenPSX2AmigaPadAdapter
Playstation to Commodore Amiga/CD32 Controller Adapter
43 parts69 - 2 layers60 × 50 mm
Vx8 gps prototype v2.0
4x1md/vx8_gps
DIY GPS module for Yaesu VX-8DR/VX-8DE handheld transceiver.
56 parts66MIT
Questions
How big is the Arduino taller PCB?
It measures 61 × 39.7 mm and has 2 copper layers, 1.6 mm thick.
What parts does the Arduino taller use?
37 parts, built around the ATMEGA328P-AU and MIC5239YM. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the Arduino taller KiCad files?
From the MakerAlc/tallerpcb repository on GitHub, at the commit this page was made from: the board is PCB_Propuesto_Arduino/Arduino_taller.kicad_pcb. PCBKit opens the board in the browser, with nothing to install.
Can I use the Arduino taller design in my own project?
Its repository states no licence, so its author keeps all rights: ask MakerAlc before reusing the design.