
Slaveboard
Magnetile/magnetile-hardware
A open source modular wireless input device. Based on nRF52840

A open source modular wireless input device. Based on nRF52840
SnapCore Devboard Rev1 is an open-source printed circuit board by Magnetile, from the Magnetile/magnetile-hardware repository on GitHub, published under the MIT licence. It is a 4-layer board of 26.8 × 47.6 mm with 63 parts on 80 nets, routed with 736 tracks and 112 vias.
It is built around the TP4057, XC6220B331MR and AMCA31-2R450G-S1F-T3, with the AO3407A and TS-1187A-B-A-B among its other parts. Its parts include 20 capacitors, 13 resistors, 3 ICs, 3 diodes and 2 connectors. It belongs with the microcontroller boards boards and the nRF52 and nRF5x boards of this library.
Magnetile is a modular wireless input device. A central hub connects to interchangeable input tiles - mechanical keys, rotary encoders, sliders, display keys - via magnetic pogo pin connectors. The hub presents as a single BLE HID device to the host. Everything is open source.
Personal project by a maker in Bavaria, Germany. Not for commercial sale.
Tiles are hot-swappable modules. Each tile has its own small MCU communicating over I²C. The hub aggregates all input and handles the BLE stack. A single LiPo cell in the hub powers the entire system through the pogo pins.
The SnapCore is the first hardware in this repository — the nRF52840-based hub PCB.
| Component | Part | Notes |
|---|---|---|
| MCU | Nordic nRF52840 (AQFN-73) | BLE 5, USB, 1MB flash, 256KB RAM |
| LDO | XC6220B331MR-G (Torex, SOT-23-5) | 3.3V, 1A, ~8µA quiescent |
| Battery charger | TP4056 | Single-cell LiPo, ~300mA charge rate |
| USB | USB-C, 5.1kΩ CC pull-downs | |
| HF crystal | 32 MHz | nRF52840 system clock |
| RTC crystal | 32.768 kHz | Low-power RTC |
| QSPI flash | W25Q128 (16 MB) | Planned for rev 2 |
| Antenna | PCB trace (meander) | SWRA117D reference, tunable RF matching |
| Tile bus | I²C with 4.7kΩ pull-ups | Pogo pin connector |
| Layer | Function |
|---|---|
| F.Cu | Components + signals |
| In1.Cu | Solid GND plane |
| In2.Cu | Power distribution + overflow signals |
| B.Cu | Signals |
Tiles are designed to be cheap and simple. The hub owns the BLE stack; tiles just report their input state over I²C when polled.
Tile MCU target: CH32V003 (RISC-V, I²C slave)
Each tile exposes:
The pogo pin connector carries: VCC, GND, SDA, SCL, and an optional INT line for event-driven wake.
Full tile specification in docs/connector-pinout.md.
Firmware lives in the companion repository: magnetile-firmware
| Component | Stack |
|---|---|
| RTOS | Zephyr / Nordic NCS |
| BLE profile | HID over GATT |
| Wireless config | Web Bluetooth API (browser-based) |
| Debug | RTT (Segger J-Link / nRF9160 DK) |
| Hub–tile protocol | I²C polling, CH32V003 slave firmware |
| Milestone | Status |
|---|---|
| Schematic rev 1 | ✅ Complete |
| PCB layout rev 1 | ✅ Complete |
| Fab files (JLCPCB) | 🔄 In progress |
| Rev 1 bring-up | ⏳ Pending |
| Tile hardware | ⏳ Rev 2 |
| Firmware (hub) | 🔄 In progress |
| Tile firmware | ⏳ Rev 2 |
| Web config UI | ⏳ Planned |
All design files are in KiCad 9. Fab outputs (Gerbers, BOM, CPL) for JLCPCB are in snapcore/fab/.
Preferred suppliers: JLCPCB (PCB + assembly), LCSC (components).
This project is designed around JLCPCB's manufacturing ecosystem. If you want to replicate the build, the Gerbers and BOM are ready to upload directly:
For managing orders across services - PCB fabrication, assembly, 3D printing, CNC - JLCPCB offers JLCONE, a unified desktop platform that consolidates their full manufacturing stack (JLCPCB, JLC3DP, JLCCNC, JLCMC) into one interface. You can upload files, place orders, and track shipments across all services in one place. The desktop version includes a coupon bundle covering various services and shipping.
This project's prototype run is supported by JLCPCB. Their PCB fabrication and SMT assembly service makes iterating on dense, complex boards like the SnapCore genuinely accessible for independent open source hardware projects.
MIT - see LICENSE.
This is a personal project in active development. Issues and suggestions are welcome. See CONTRIBUTING.md before opening a pull request.
| Qty | Value | Footprint | References |
|---|---|---|---|
| 4 | 12pF | Capacitor_SMD:C_0402_1005Metric | C9, C10, C20, C21 |
| 4 | 2.2uF | Capacitor_SMD:C_0402_1005Metric | C1, C3, C13, C22 |
| 4 | MountingHole | MountingHole:MountingHole_2.2mm_M2_ISO7380_Pad | H1, H2, H3, H4 |
| 3 | 2.2uF | Capacitor_SMD:C_0603_1608Metric | C6, C11, C12 |
| 2 | 33R | Resistor_SMD:R_0402_1005Metric | R19, R20 |
| 2 | 4.7k | Resistor_SMD:R_0402_1005Metric | R16, R17 |
| 2 | 5.1k | Resistor_SMD:R_0402_1005Metric | R1, R2 |
| 1 | 0.5pF | Capacitor_SMD:C_0402_1005Metric | C16 |
| 1 | 0.8pF | Capacitor_SMD:C_0402_1005Metric | C15 |
| 1 | 100K | Resistor_SMD:R_0402_1005Metric | R6 |
| 1 | 100nF | Capacitor_SMD:C_0603_1608Metric | C18 |
| 1 | 100nF | Capacitor_SMD:C_0402_1005Metric | C8 |
| 1 | 100nF | Capacitor_SMD:C_0805_2012Metric | C7 |
| 1 | 100pF | Capacitor_SMD:C_0402_1005Metric | C19 |
| 1 | 10k | Resistor_SMD:R_0402_1005Metric | R18 |
| 1 | 10uF | Capacitor_SMD:C_0402_1005Metric | C5 |
| 1 | 10uH | Inductor_SMD:L_0402_1005Metric | L2 |
| 1 | 1M_1% | Resistor_SMD:R_0603_1608Metric | R10 |
| 1 | 2.2k | Resistor_SMD:R_0402_1005Metric | R9 |
| 1 | 2.2uF | Capacitor_SMD:C_0805_2012Metric | C4 |
| 1 | 32.768KHz | Crystal:Crystal_SMD_3215-2Pin_3.2x1.5mm | Y1 |
| 1 | 32Mhz | Crystal:Crystal_SMD_2016-4Pin_2.0x1.6mm | Y3 |
| 1 | 330R | Resistor_SMD:R_0603_1608Metric | R7 |
| 1 | 3V3 | TestPoint:TestPoint_Pad_D2.0mm | TP3 |
| 1 | 4.7nH | Inductor_SMD:L_0402_1005Metric | L1 |
| 1 | 4k | Resistor_SMD:R_0603_1608Metric | R8 |
| 1 | 500mA | Fuse:Fuse_1206_3216Metric | F1 |
| 1 | 510k_1% | Resistor_SMD:R_0603_1608Metric | R11 |
| 1 | 820pF | Capacitor_SMD:C_0402_1005Metric | C14 |
| 1 | AMCA31-2R450G-S1F-T3 | AMCA31-2R450G-S1F-T3:XDCR_AMCA31-2R450G-S1F-T3 | AE2 |
| 1 | AO3407A | Package_TO_SOT_SMD:SOT-23 | Q1 |
| 1 | Battery JST 3.7V | Connector_JST:JST_PH_B2B-PH-K_1x02_P2.00mm_Vertical | BAT_CONN1 |
| 1 | CHG0 | LED_SMD:LED_0603_1608Metric | RED1 |
| 1 | Conn_01x18_Pin | Connector_PinHeader_1.27mm:PinHeader_1x18_P1.27mm_Vertical | J3 |
| 1 | GND | TestPoint:TestPoint_Pad_D2.0mm | TP4 |
| 1 | Green | LED_SMD:LED_0805_2012Metric | D3 |
| 1 | LOGO | Pictures:FixedLogoFlipped | G*** |
| 1 | PROG | TestPoint:TestPoint_Pad_D2.0mm | TP7 |
| 1 | RESET | TestPoint:TestPoint_Pad_D2.0mm | TP5 |
| 1 | RF | TestPoint:TestPoint_Pad_D2.0mm | TP6 |
| 1 | Red | LED_SMD:LED_0805_2012Metric | D4 |
| 1 | SDM20U40-7, 40V;250mA | Diode_SMD:D_SOD-523 | D5 |
| 1 | TP4057 | Package_TO_SOT_SMD:TSOT-23-6 | U4 |
| 1 | TS-1187A | Button_Switch_SMD:SW_Push_1P1T_XKB_TS-1187A | SW2 |
| 1 | USB_C_Receptacle_USB2.0_16P | Connector_USB:USB_C_Receptacle_GCT_USB4105-xx-A_16P_TopMnt_Horizontal | J2 |
| 1 | VBAT | TestPoint:TestPoint_Pad_D2.0mm | TP2 |
| 1 | VBUS | TestPoint:TestPoint_Pad_D2.0mm | TP1 |
| 1 | XC6220B331MR | Package_TO_SOT_SMD:SOT-23-5 | U2 |
| 1 | nRF52840-QIXX | Package_DFN_QFN:Nordic_AQFN-73-1EP_7x7mm_P0.5mm | U1 |

Magnetile/magnetile-hardware
A open source modular wireless input device. Based on nRF52840





LRNATHD/CH572D-Board
example board using WCH's CH572 Bluetooth microcontroller

PTR-projects/PTR_mini_hardware
Welcome to the KPPTR-hardware repository! This repository contains the design files for the hardware components used in the KPPTR project.

dac63701/SmartCard
The goal of this project was to create a small and slim Bluetooth tracker that would fit into a credit card enclosure. To do this, a 0.8mm thin 80mah battery was used along with a 0.8mm PCB.

davispe1/wearable-imu
Node PCB — revision 1.0. 4-layer board (F.Cu, In1.Cu, In2.Cu, B.Cu).
It measures 26.8 × 47.6 mm and has 4 copper layers, 1.6 mm thick.
63 parts, built around the TP4057, XC6220B331MR, AMCA31-2R450G-S1F-T3 and AO3407A. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
From the Magnetile/magnetile-hardware repository on GitHub, at the commit this page was made from: the board is SnapCore/KiCAD/DevBoard/SnapCore-Devboard-Rev1/SnapCore-Devboard-Rev1.kicad_pcb and its schematic SnapCore/KiCAD/DevBoard/SnapCore-Devboard-Rev1/SnapCore-Devboard-Rev1.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Its repository publishes it under the MIT licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).