Skip to the content
2 layers100 × 100 mmLED controller, the printed circuit board in 3D

LED mount that is compatible with the Thorlabs 30 mm cage plate

Size
100 × 100 mm
Copper layers
2
Thickness
1.6 mm
Parts
45
Nets
84
Pads
314
Tracks, vias
1,536, 736
Pours
2
Routed
Yes
KiCad
KiCad 8.0 (file 20240108)
Created
1 Nov 2023
Updated
19 Nov 2025

Overview

LED controller is an open-source printed circuit board by Llamero, from the Llamero/30mm_cage_plate_LED_MCPCB repository on GitHub. It is a 2-layer board of 100 × 100 mm with 45 parts on 84 nets, routed with 1,536 tracks and 736 vias.

It is built around the TEENSY 4.1, ELUMOASAQ2C22 and BAT54BRW. Its parts include 12 capacitors, 7 ICs, 5 connectors, 3 switches and 2 diodes. It belongs with the NXP (LPC, Kinetis, i.MX RT) boards of this library.

Main components

3

README

README.md

30 mm Cage Plate LED Driver

Top view of LED driver

4x LED 30 mm Cage Plate Board Description:

This board is an entirely self-contained LED and driver circuitry designed to be compatible with the Thorlabs 30 mm cage plate system: https://www.thorlabs.com/navigation.cfm?guide_id=2004

Top view of LED driver

The LEDs on the board are closely spaced so that all four LEDs efficiently couple into a 5 mm liquid light guide or other optical paths.

Side view of LED with opticas

Each board can drive up to four individual LEDs, and includes a thermistor for temperature monitoring. The the LED current is regulated by an AL8843, allowing LEDs to be driven with up to three amps of current. The AL8843 also allows for both PWM control as well as analog current control down to 10% of the current limit (see below for setting max current limit).

Four p-channel mosfets on the board create a 1x4 multiplexer that allows individual LEDs to be toggled on by pulling the corresponding LED channel's gate to ground. Each gate has a 4.7 kOhm pullup resistor so that each channel defaults to being off if not connected.

To turn the LEDs off more rapidly, there is also a 38V TVS diode parallel to the inductor that can be used to dump the residual energy stored in the inductor by setting all four multiplexer channels high.

A heatsink and fan can also be mounted to the backside of the cage plate for active cooling of high-current LEDs.

Side view of LED driver

3x 30 mm Cage Plate Controller Description:

This repository also includes the design files for a controller that can operate up to three 30 mm cage plates for a total of 12 LEDs.

LED controller top

The controller is powered by a Teensy 4.1 which allows for precise timing control (<10 ns hysteresis) of each LED, as well a complex programmable control.

On the back of the driver, each board connects to the driver via a shielded cat5 ethernet cable. Additionally, there is a cat5 port with both a 12V supply and three channels of 5V PWM outputs for both powering the fans for each board as well as controlling the fan speed. Finally, there are four protected digital inputs allowing for control signals up to -15V/+18V.

On the front of the driver, there is a potentiometer for controlling the intensity of each of the three LED boards, as well as a pushbutton to select the channel for each board. Additionally, each pushbutton includes a red-green LED indicator to indicate which of the four LED channels is active.

Driver Software:

There is software prewritten for the Teensy 4.1 that allows for both manual and programmable control, for syncing to triggers or other inputs.

Additionally, there is a GUI that allows for software control of the LED driver, we well as access to five preset programmable sync modes (digital, analog, confocal, serial, and custom), as well as custom configuration of the LED driver.

GUI

Design:

To view and modify the board, download KiCAD https://www.kicad.org/, and open the project file.

Make sure to modify the LED footprint to match the footprint for your desired LEDs, and to change the current limit resistor to the desired value (see AL8843 datasheet, p. 11):

text
RSET (Ω)  Nominal Average Output Current (mA)
0.033     3,000
0.05      2,000
0.067     1,500
0.1       1,000
0.15      667
0.3       333

When changing the LED footprints, ensure that the LEDs remain closely spaced for efficient coupling into a liquid light guide.

Ordering:

The BOM can be found here: 30mm_cage_plate_LED_MCPCB/4x-LED-array/BOM%20-%20Portable%20Tetrachromatic%20Display.xlsx

This BOM includes all the parts needed to build both the LED driver boards as well as the LED controller board.

To order the PCBs, upload the Gerber files to your desired PCB vendor, such as: https://www.pcbway.com/project/shareproject/W55957ASK98_30_mm_Cage_Plate_LED_MCPCB_kicad_pcb_3d2c1975.html Make sure that the LED boards are MCPCBs and not FR4. The driver board can be ordered as an FR4 board.

Assembly:

To start, spread thermal epoxy onto the flat side of a Thorlabs 30 mm blank cage plate.

Spread epoxy

Press the MCPCB board firmly to the cage plate using a vise or heavy weights. vise

Use a pipette tip or other fine tipped tool to remove excess epoxy from the cage rod holes. Remove excess epoxy

Slide the board across the cage plate as needed to align the cage rod holes and allow the epoxy to cure overnight.

Next, assemble the board similarly to other reflow soldering boards. See the following manual: https://github.com/Llamero/Light_Color_and_Intensity_Datalogger/blob/master/Data%20logger%20assembly%20manual.pdf

Finally, use thermal epoxy to connect the heatsink to the Thorlabs cage plate, press firmly, and bake at 50°C overnight to cure.

heatsink

Operation:

Connect a 5V to 20V power supply, with the positive terminal connected to the Vin pin and the negative terminal connected to the Gnd pin. To control the LED current, you can send a +0.4V (10% current) to +2.5V (100% current) to the Ctrl pin. The LED can also be dimmed with PWM with a voltage up to 5V. To control the mux, pull the channel you want to turn on to ground (0V). To monitor temperature, measure the resistance of the thermistor.

Parts

45
QtyValueFootprintReferences
111µFCapacitor_SMD:C_0603_1608MetricC1, C2, C3, C4, C5, C6, C7, C8, C9, C10, C11
4MountingHoleCustom Footprints:1-4_20 standoffH1, H2, H3, H4
310kCustom Footprints:P160KN2-4QC20B10KRV1, RV2, RV3
33600Resistor_SMD:R_Array_Convex_4x0603RN1, RN2, RN4
34x Gate DriverCustom Footprints:D16-4x gate driverU1, U2, U3
3ELUMOASAQ2C22Custom Footprints:ELUMOASAQ2C22_CNKSW1, SW2, SW3
215V DC-DCCustom Footprints:SRS-1215-2PS1, PS2
2BAT54BRWPackage_TO_SOT_SMD:SOT-363_SC-70-6D1, D2
1220µFCapacitor_THT:CP_Radial_D6.3mm_P2.50mmC12
1390Resistor_SMD:R_Array_Convex_4x0603RN3
13x 10-Bit DACCustom Footprints:DAC084S085CIMMXNOPBU6
13x Analog SwitchCustom Footprints:SN74LV4053ADRU5
13x Level ShifterCustom Footprints:TSSOP14_NXB0104_NEXU7
14x RJ45Custom Footprints:RJ45_x4-RJSSE-5380-04J2
18P8C_ShieldedCustom Footprints:1x RJ45J5
1Barrel_Jack_SwitchCustom Footprints:DC-jack_54-00165J1
1Conn_01x02_SocketConnector_PinSocket_2.54mm:PinSocket_1x02_P2.54mm_VerticalJ7
1Conn_01x03_SocketConnector_PinSocket_2.54mm:PinSocket_1x03_P2.54mm_Vertical_SMD_Pin1LeftJ6
1Logo_Center_PositiveCustom Footprints:PolaritySYM3
1Logo_Open_Hardware_SmallCustom Footprints:CC-BY-SA SymbolSYM1
1Logo_Open_Hardware_SmallSymbol:OSHW-Logo_5.7x6mm_SilkScreenSYM2
1Teensy4.1Custom Footprints:Teensy_3_6_with_headersU4

More from Llamero/30mm_cage_plate_LED_MCPCB

1
  • 2 layers40 × 40 mm30 mm Cage Plate LED MCPCB, the printed circuit board in 3D

    30 mm Cage Plate LED MCPCB

    Llamero/30mm_cage_plate_LED_MCPCB

    LED mount that is compatible with the Thorlabs 30 mm cage plate

    27 parts9

Similar boards

  • 2 layers100 × 100 mmFour Channel MHz LED Driver, the printed circuit board in 3D

    Four Channel MHz LED Driver

    Llamero/Four_Channel_MHz_LED_Driver

    High Speed Four Channel LED Driver that can run up to 30A

    96 parts6
  • 2 layers118.1 × 101.6 mmTeensy eurorack, the printed circuit board in 3D

    Teensy eurorack

    newdigate/teensy-eurorack

    Hardware Design: Eurorack shield for teensy 4.1 with 14 in / 16 out analog channels

    102 parts259MIT
  • 2 layers240 × 240 mmKfchess, the printed circuit board in 3D

    Kfchess

    misprit7/real-time-chess

    A physical chess board without the concept of turns

    235 parts254MIT
  • 2 layers304.8 × 170.8 mm00Key, the printed circuit board in 3D

    00Key

    ZeroZeroOne-dev/00Key

    00Key a 75% keyboard

    268 parts241GPL-3.0
  • 2 layers66.5 × 36.5 mmSyncBoard, the printed circuit board in 3D

    SyncBoard

    anthonytec2/OctoSense

    OctoSense is a multimodal dataset

    9 parts211MIT
  • 2 layers312 × 140 mmTsynth2 Rev1.3, the printed circuit board in 3D

    Tsynth2 Rev1.3

    Electrotechnique/TSynth-Teensy4.1

    TSynth for Teensy 4.1

    108 parts182
  • 2 layers316 × 119 mmTeensy Grovebox, the printed circuit board in 3D

    Teensy Grovebox

    jerry20091103/Teensy_Grovebox

    A portable synth and music multi-tool made with Teensy 4.1

    142 parts150MIT
  • 2 layers304.8 × 95.2 mmLMN, the printed circuit board in 3D

    LMN

    FundamentalFrequency/LMN-3-ECAD

    Electrical CAD Files for the LMN-3 Project

    106 parts106CC-BY-SA-4.0

Questions

How big is the LED controller PCB?

It measures 100 × 100 mm and has 2 copper layers, 1.6 mm thick.

What parts does the LED controller use?

45 parts, built around the TEENSY 4.1, ELUMOASAQ2C22 and BAT54BRW. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the LED controller KiCad files?

From the Llamero/30mm_cage_plate_LED_MCPCB repository on GitHub, at the commit this page was made from: the board is KiCAD/LED Controller/LED controller.kicad_pcb and its schematic KiCAD/LED Cage Plate/30 mm Cage Plate LED MCPCB.kicad_sch. PCBKit opens the board in the browser, with nothing to install.

Can I use the LED controller design in my own project?

Its repository states no licence, so its author keeps all rights: ask Llamero before reusing the design.