Skip to the content
2 layers118.1 × 101.6 mmTeensy eurorack, the printed circuit board in 3D

Hardware Design: Eurorack shield for teensy 4.1 with 14 in / 16 out analog channels

Size
118.1 × 101.6 mm
Copper layers
2
Thickness
1.6 mm
Parts
102
Nets
137
Pads
389
Tracks, vias
1,422, 455
Pours
5
Routed
Yes
KiCad
KiCad 5 (file 20171130)
Created
27 May 2018
Updated
22 Jul 2023

Overview

Teensy eurorack is an open-source printed circuit board by newdigate, from the newdigate/teensy-eurorack repository on GitHub, published under the MIT licence. It is a 2-layer board of 118.1 × 101.6 mm with 102 parts on 137 nets, routed with 1,422 tracks and 455 vias.

It is built around the TEENSY 4.1 and CS42448-CQZ. Its parts include 46 capacitors, 32 resistors, 9 connectors and 2 ICs. It belongs with the audio and music boards and the NXP (LPC, Kinetis, i.MX RT) boards of this library.

Main components

2

README

README.md

teensy eurorack audio shield

Version 2.1 Teensy 4.1 success Join the chat at https://gitter.im/newdigate/teensy-eurorack kicad pcb ops CI teensy40 built with kicad MIT license

Sponsored by:

open source hardware and software for a 30-channel (14 in / 16 out) 16-bit analog teensy 4.1 eurorack shield

  • add peripherals to extend your teensy 4.1 to interface with
    • analog line audio (6 in / 8 out)
    • analog control voltages (8 in / 8 out: -10 to +10 volts)
    • midi in/out
    • microSD socket breakout
    • USB-A host and USB-B devices
    • 4 potentiometers, 3 encoders w/switch
  • online designer teensy eurorack audio gui ^

updates

contents

sponsor

specifications

  • microcontrollers:
  • audio: multi-channel audio codec ( 6-in / 8-out 24-bit sound card - CS42448 )
    • the audio codec circuit originally started as a discussion on quad audio channel outputs and a pcb design integrating teensy and cs42448 from Paul Stoffregen on pjrc forum
  • analog control voltage ins/outs: -10V to 10V 16bit/sample, 8 x inputs and 8 x outputs ( ad7606, 2x ad5754 )
  • display: ST7735 128x128 16bit-color tft display
  • breakouts:
    • microSD card socket,
    • USB host/device,
    • midi in/out,
    • knobs (4 x pots, 3 x encoders w/switch)
  • panel: 24HP aluminium panel mounted for eurorack case
  • programability:
    • write arduino compatible c/c++ firmware & program using arduino/teensyduino
    • arm gnu toolchain downloads
    • teensy audio library

license

  • All artifacts are MIT license unless otherwise specified on a per file basis.

open source software stack

build

order pcbs

sourcing parts

Most parts are available from mouser.com - you can use the mouser BOMs below as a template to create an order.

mouser boms

parts not on mouser boms

  • panel:
  • mainboard:
    • 2.54mm pitch pin headers and sockets
      • J28: Eurorack power header: either male or female (2 x 8), I use female as my eurorack power (tip top) has male connectors.
  • breakout:
    • uSD card socket: pjs008u-3000-0 yamaichi

    • display: ST7735 (1.44 inch TFT LCD ST7735 SPI display module 128*128 8pin 65K color)

    • 16 x thonkiconns: PJ398SM

    • 4 x 9mm snap-in pots: alpha-9mm-pots - You want linear (B-series) not audio (A-series) B5K or B10K should be ideal.

    • 3 x rotary encoders w/switches: Half axis (D-shaft) rotary encoder, handle/axis length: 20mm, EC11/EC12 digital potentiometer with switch - 5Pin

Update: USB-A-S-X-X-VT is no longer available. Amphenol Commercial Products GSB11111ALF looks like it may be a good replacement.

interactive html boms online

source code

improvements

At this point Im just focusing on finalising/polishing the current version, but there are some improvements I'd like to make at some point.

  • add 4x jack sockets for analog output of knobs on breakout board.
  • use 3.5mm jack sockets (as well as standard midi din connectors) for midi in and out.
  • switch to active audio input and output circuitry, allow switchable 0dB / 12dB gain, for guitar signals.
  • let me know if you're think there something else that can be improved, added, removed.

There is a journal of my progress (its a bit out of date, sorry) - journal.md

What you can do if you like to see progress with this project?

  • #sponsor...
  • star this repository (means you need a github account - go for it!!)
  • subscribe Nic N on youtube
  • download kicad and freecad, clone this repo, make improvements, commit & send pull-requests, and raise issues...

printed circuit boards

mainboard

  • standard double layer printed circuit board
    • thinkness: 1.6mm
    • minimum trace: 6 mil
    • minimum clearance: 6 mil
    • dimension: 118mm*102mm
  • socket to connect teensy 4.0 board
  • cs42448 audio codec
  • 3 x stereo 6.35mm TRS jack inputs
  • 4 x stereo 6.35mm TRS jack outputs
  • pin sockets to connect breakout board

breakout board

  • 2 layer printed circuit board
    • thinkness: 1.6mm
    • minimum trace: 6 mil
    • minimum clearance: 6 mil
    • dimension: 110mm*111mm
  • 8 x 3.5mm jack socket for analog control voltage inputs
  • 8 x 3.5mm jack socket for analog control voltage outputs
  • midi in/out DIN sockets
  • usb device/host
    • USB-B: USB device mode
    • USB-A: USB host mode
  • micro-SD card socket
  • 4 x linear pots
  • 3 x rotary encoders with switches

schematics

panel design

assembly technical drawings

youtube videos

versions

v2.1 (Saturday 3 April 2021)

  • Improvement: Mainboard: Tie LRCLK pin 20 to pin40 to sync DAC/ADC sampling w/ audio sampling
  • FIXED: breakout: add 1k pull-up resistor to MIDI rx pin
  • mainboard: silkscreen: add Kicad OpenSourceHardware logo
  • breakout: silkscreen: add Kicad OpenSourceHardware logo

v2.0.3 (Saturday 13/02/2021)

  • breakout: st7735 display changed vcc, reset, backlight from 5v to 3v3.

v2.0.2 (31/01/2021)

  • Mainboard: spaced out traces as there appeared to be some interference under certain circumstances.

v2.0.1 (27/01/2021)

  • Mainboard: add daisy chain TX/RX connector on back side to communicate between multiple boards
  • Breakout board: changed back to double layer board.

v2.0.0(b)

  • Breakout board: Corrected polarity of +-12V pin headers on breakout board (ouch!!!)
  • change ADC to use external 2.5v voltage reference, same as DAC voltage reference now

v2.0.0

  • SPI: separated ADC, DAC from display:
    • st7735 display has its own dedicated SPI - (SPI0, stays the same)
    • ADC / DAC are now sharing SPI1
  • integrated ADC and DAC into teensy audio library.
  • added one more ad5754 DAC for total of 8 control voltage analog output channels

v1.9.1b

  • mainboard: correction: reconnected LRCLK to codec.

v1.9.1

  • connected DAC_SCK output (pin 19) to pin 31
    • allow cable select to be asserted on minor spi data cycle after every 24 or 48 spi clock cycles, using interrupt on pin 31.
      • hopefully this will allow DMA spi transfers to AD5754 and which will make integration with teensy audio library much easier

v1.9

updated to teesy 4.1 and improvements to make easier to build

  • updated from teensy 4.0 to teensy 4.1
  • schematic, footprint and pcb clean-up
    • replaced footprints imported from eagle with native kicad footprints
  • removed atmel samd21 and gpio ICs
  • replaced gpio with AD5754 (extra 4 DAC channels)
  • replaced RGB encoders with regular encoders
  • replaced analog-GND-to-digital-GND footprint with a 0805 zero ohm resistor footprint. (DRC checks can pass now...)
  • (temporarily) removed serial TX/RX to unused eurorack power pins

todo

  • finalize design / circuits / boards
  • order (v.2.1)
  • assemble
  • testing
    • CS42448 audio codec
      • Audio input
      • Audio output
    • control voltage input
    • control voltage output
    • usb host
    • usb device
    • midi in
    • midi out
    • st7735 display
    • sd card extension & adapter
  • Document
    • order & build process
    • software process
  • Firmware

continuous-integration

credits

sponsored by

Massive thanks to these generous people who have provided support!

  • Hannes Schnaitter
  • Daniel Hengeveld thedaniel on github
  • Derek Brost
  • Martin Eigel
  • Morgan Massens

Parts

102
QtyValueFootprintReferences
142700pCapacitor_SMD:C_0805_2012MetricC47, C48, C51, C52, C55, C56, C59, C60, C63, C64, C67, C68, C71, C72
94.7uCapacitor_SMD:C_0805_2012MetricC12, C45, C46, C49, C50, C53, C54, C69, C70
810kResistor_SMD:R_0805_2012MetricR8, R9, R12, R13, R16, R17, R32, R33
810uCapacitor_SMD:C_0805_2012MetricC7, C18, C57, C58, C61, C62, C65, C66
8560Resistor_SMD:R_0805_2012MetricR10, R11, R14, R15, R18, R19, R34, R35
7AudioJack3_SwitchTRfootprints:ACJS-MV5J4, J5, J6, J7, J8, J9, J10
60.1uCapacitor_SMD:C_0805_2012MetricC5, C10, C11, C13, C15, C17
6100kResistor_SMD:R_0805_2012MetricR20, R21, R24, R25, R28, R29
6150Resistor_SMD:R_0805_2012MetricR22, R23, R26, R27, R30, R31
44.7uCapacitor_THT:CP_Radial_D5.0mm_P2.50mmC1, C2, C3, C4
4Conn_01x04Connector_PinHeader_2.54mm:PinHeader_1x04_P2.54mm_VerticalJMUSBA1, JMUSBB1, JUSBA1, JUSBB1
30.01uCapacitor_SMD:C_0805_2012MetricC6, C8, C9
32kResistor_SMD:R_0805_2012MetricR1, R3, R4
2Conn_01x03Connector_PinHeader_2.54mm:PinHeader_1x03_P2.54mm_VerticalJDAISYM1, JDAISYS1
2Conn_01x08Connector_PinHeader_2.54mm:PinHeader_1x08_P2.54mm_VerticalJM3, JM4
10Resistor_SMD:R_0805_2012MetricR2
1100uCapacitor_SMD:C_1206_3216MetricC16
122uCapacitor_SMD:C_0805_2012MetricC14
1CONN_01x14Connector_PinHeader_2.54mm:PinHeader_1x14_P2.54mm_VerticalJM2
1CS42448Package_QFP:LQFP-64_10x10mm_P0.5mmU1
1Conn_01x02Connector_PinHeader_2.54mm:PinHeader_1x02_P2.54mm_VerticalJ27
1Conn_01x14Connector_PinHeader_2.54mm:PinHeader_1x14_P2.54mm_VerticalJM1
1Conn_02x08_Odd_EvenConnector_PinHeader_2.54mm:PinHeader_2x08_P2.54mm_VerticalJ28
1Ferrite_BeadInductor_SMD:L_0603_1608MetricFB1
1Teensy4.1footprints:Teensy41_thtU4

The 100 most common of 102 parts.

More from newdigate/teensy-eurorack

2
  • 2 layers110.5 × 111.1 mmTeensy eurorack breakout, the printed circuit board in 3D

    Teensy eurorack breakout

    newdigate/teensy-eurorack

    Hardware Design: Eurorack shield for teensy 4.1 with 14 in / 16 out analog channels

    78 parts259MIT
  • 2 layers24.8 × 10.9 mmUSD extender male, the printed circuit board in 3D

    USD extender male

    newdigate/teensy-eurorack

    Hardware Design: Eurorack shield for teensy 4.1 with 14 in / 16 out analog channels

    3 parts259MIT

Similar boards

  • 2 layers114.2 × 58.3 mmCs42448-board, the printed circuit board in 3D

    Cs42448-board

    maximeborges/audio_processor

    ip route add default via 192.168.2.1 dev eth0

    135 parts
  • 2 layers240 × 240 mmKfchess, the printed circuit board in 3D

    Kfchess

    misprit7/real-time-chess

    A physical chess board without the concept of turns

    235 parts254MIT
  • 2 layers304.8 × 170.8 mm00Key, the printed circuit board in 3D

    00Key

    ZeroZeroOne-dev/00Key

    00Key a 75% keyboard

    268 parts241GPL-3.0
  • 2 layers66.5 × 36.5 mmSyncBoard, the printed circuit board in 3D

    SyncBoard

    anthonytec2/OctoSense

    OctoSense is a multimodal dataset

    9 parts211MIT
  • 2 layers312 × 140 mmTsynth2 Rev1.3, the printed circuit board in 3D

    Tsynth2 Rev1.3

    Electrotechnique/TSynth-Teensy4.1

    TSynth for Teensy 4.1

    108 parts182
  • 2 layers316 × 119 mmTeensy Grovebox, the printed circuit board in 3D

    Teensy Grovebox

    jerry20091103/Teensy_Grovebox

    A portable synth and music multi-tool made with Teensy 4.1

    142 parts150MIT
  • 2 layers304.8 × 95.2 mmLMN, the printed circuit board in 3D

    LMN

    FundamentalFrequency/LMN-3-ECAD

    Electrical CAD Files for the LMN-3 Project

    106 parts106CC-BY-SA-4.0

Questions

How big is the Teensy eurorack PCB?

It measures 118.1 × 101.6 mm and has 2 copper layers, 1.6 mm thick.

What parts does the Teensy eurorack use?

102 parts, built around the TEENSY 4.1 and CS42448-CQZ. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the Teensy eurorack KiCad files?

From the newdigate/teensy-eurorack repository on GitHub, at the commit this page was made from: the board is hardware/boards/teensy-eurorack.kicad_pcb. PCBKit opens the board in the browser, with nothing to install.

Can I use the Teensy eurorack design in my own project?

Its repository publishes it under the MIT licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).