2 layers65 × 56 mm
Owl driver board
geezacoleman/owl-driver-board
Development of a board that receives GPIO input and allows on/off control of connected solenoids.
182 parts14MIT
2 layers56.5 × 65 mm
Pi Breakout Board
Jkillelea/Pi_Breakout_Board- Size
- 56.5 × 65 mm
- Copper layers
- 2
- Thickness
- 1.6 mm
- Parts
- 75
- Nets
- 47
- Pads
- 258
- Tracks, vias
- 479, 33
- Pours
- 2
- Routed
- Yes
- KiCad
- KiCad 5 (file 20171130)
- Created
- 11 Feb 2019
- Updated
- 23 Apr 2019
Overview
Pi Breakout Board is an open-source printed circuit board by Jkillelea, from the Jkillelea/Pi_Breakout_Board repository on GitHub. It is a 2-layer board of 56.5 × 65 mm with 75 parts on 47 nets, routed with 479 tracks and 33 vias.
It is built around the PCA9685PW and SMBJ5.0A. Its parts include 29 resistors, 13 capacitors, 8 connectors, 5 diodes and 5 transistors. It belongs with the interfaces and adapters and microcontroller boards boards of this library.
Main components
2
PCA9685PW
TSSOP-28-40℃~+85℃ 100kHz~1MHz 16 2.3V~5.5V 25mA 5.5V Built-in PWM TSSOP-28 LED Drivers ROHSNXP SemiconductorsLED Drivers
SMBJ5.0A
DO-214AA(SMB)-65℃~+150℃ 5V 600W@10/1000us 65.3A@10/1000us 7V 800uA 9.2V TVS Unidirectional DO-214AA(SMB) ESD and Surge Protection (TVS/ESD) ROHSMDDESD And Surge Protection (TVS/ESD)
Parts
75| Qty | Value | Footprint | References |
|---|---|---|---|
| 16 | 10K | Resistor_SMD:R_1206_3216Metric_Pad1.42x1.75mm_HandSolder | R1, R2, R7, R8, R9, R10, R11, R12, R13, R14, R15, R16, R17, R18, R20, R29 |
| 9 | TestPoint | TestPoint:TestPoint_Pad_D2.0mm | TP1, TP3, TP4, TP5, TP6, TP7, TP8, TP9, TP10 |
| 8 | 18K 1% | Resistor_SMD:R_1206_3216Metric_Pad1.42x1.75mm_HandSolder | R19, R21, R22, R23, R24, R25, R26, R27 |
| 7 | 0.1U CERAMIC | Capacitor_SMD:C_1210_3225Metric_Pad1.42x2.65mm_HandSolder | C1, C2, C4, C6, C7, C9, C10 |
| 4 | 65R | Resistor_SMD:R_0805_2012Metric_Pad1.15x1.40mm_HandSolder | R3, R4, R5, R6 |
| 4 | MountingHole | MountingHole:MountingHole_2.7mm_M2.5 | H1, H2, H3, H4 |
| 4 | Q_NMOS_GDSD | Package_TO_SOT_SMD:SOT-223 | Q1, Q2, Q3, Q4 |
| 3 | 1uF 25V | Capacitor_SMD:C_1210_3225Metric_Pad1.42x2.65mm_HandSolder | C11, C12, C13 |
| 2 | 1uF | Capacitor_Tantalum_SMD:CP_EIA-3216-18_Kemet-A_Pad1.58x1.35mm_HandSolder | C3, C5 |
| 2 | Conn_01x08_Male | Connector_PinHeader_2.54mm:PinHeader_1x08_P2.54mm_Vertical | J5, J6 |
| 2 | LED GREEN | LED_SMD:LED_0805_2012Metric_Pad1.15x1.40mm_HandSolder | D1, D2 |
| 1 | 18K | Resistor_SMD:R_1206_3216Metric_Pad1.42x1.75mm_HandSolder | R28 |
| 1 | 47uF 60V | Capacitor_THT:CP_Radial_D6.3mm_P2.50mm | C8 |
| 1 | ADC128D818 | Package_SO:TSSOP-16_4.4x5mm_P0.65mm | U2 |
| 1 | Conn_01x02_Female | Connector_PinSocket_2.54mm:PinSocket_1x02_P2.54mm_Horizontal | J7 |
| 1 | Conn_01x04_Male | Connector_PinSocket_2.54mm:PinSocket_1x04_P2.54mm_Vertical | J8 |
| 1 | Conn_02x04_Odd_Even heater header | Connector_PinHeader_2.54mm:PinHeader_2x04_P2.54mm_Vertical | J2 |
| 1 | Conn_02x08_Odd_Even thermistor header | Connector_PinHeader_2.54mm:PinHeader_2x08_P2.54mm_Vertical | J3 |
| 1 | IRF9Z34 PMOS_GDS | Package_TO_SOT_THT:TO-220-3_Vertical | Q5 |
| 1 | LED RED | LED_SMD:LED_0805_2012Metric_Pad1.15x1.40mm_HandSolder | D4 |
| 1 | LED YELLOW | LED_SMD:LED_0805_2012Metric_Pad1.15x1.40mm_HandSolder | D3 |
| 1 | PCA9685PW | Package_SO:TSSOP-28_4.4x9.7mm_P0.65mm | U1 |
| 1 | Raspberry_Pi_2_3 | Connector_PinHeader_2.54mm:PinHeader_2x20_P2.54mm_Vertical | J1 |
| 1 | SMBJ5.0A | footprints:SMBJ5.0A | D5 |
| 1 | Screw_Terminal_01x02 | TerminalBlock:TerminalBlock_bornier-2_P5.08mm | J4 |
Similar boards
- 4 layers28 × 98.2 mm
ESP32-PoE ISO Rev N1
OLIMEX/ESP32-POE-ISO
ESP32 Power Over Ethernet board with 3000VDC Galvanic insulation
146 parts145 - 4 layers77.1 × 63.8 mm
- 2 layers98.9 × 78 mm
Siot gateway particle io
simpleiot/hardware
Hardware designs for IoT devices and sensor nodes.
28 parts9Apache-2.0 - 2 layers170 × 120 mm
- 2 layers52.6 × 48.8 mm
- 2 layers100 × 100 mm
- 4 layers180 × 110 mm
PETER
dennowiggle/Retro-PETER
3.3V Retro computer project => FPGA + RCBUS + CPU boards making a custom system.
419 parts4LGPL-2.1
Questions
How big is the Pi Breakout Board PCB?
It measures 56.5 × 65 mm and has 2 copper layers, 1.6 mm thick.
What parts does the Pi Breakout Board use?
75 parts, built around the PCA9685PW and SMBJ5.0A. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the Pi Breakout Board KiCad files?
From the Jkillelea/Pi_Breakout_Board repository on GitHub, at the commit this page was made from: the board is Pi_Breakout_Board.kicad_pcb. PCBKit opens the board in the browser, with nothing to install.
Can I use the Pi Breakout Board design in my own project?
Its repository states no licence, so its author keeps all rights: ask Jkillelea before reusing the design.