
Front
JQIamo/20A-bipolar-current-source
20A bipolar current source with water cooled sensing resistor

20A bipolar current source with water cooled sensing resistor
Rear is an open-source printed circuit board by JQIamo, from the JQIamo/20A-bipolar-current-source repository on GitHub. It is a 4-layer board of 145 × 157 mm with 99 parts on 58 nets, routed with 613 tracks and 52 vias.
It is built around the OPA388ID, BUF634T and LM7805, with the LM7905T, LM7915T and LT3080EDD among its other parts. Its parts include 41 capacitors, 28 resistors, 13 ICs, 9 connectors and 4 transistors.
20A bipolar current source with water cooled sensing resistor
| Qty | Value | Footprint | References |
|---|---|---|---|
| 19 | 0.1uF | Capacitors_SMD:C_0603 | C1, C2, C3, C17, C21, C22, C30, C31, C32, C33, C34, C35, C36, C37, C38, C39 +3 |
| 7 | 10uF | Capacitors_SMD:C_1210 | C7, C8, C12, C15, C23, C26, C27 |
| 5 | Conn_01x01_Female | zmyfootprint:SAFETY-BANANA-JACK-CT3151 | J1, J2, J5, J6, J7 |
| 4 | 0.33uF | Capacitors_SMD:C_0603 | C13, C16, C19, C20 |
| 4 | 18.2k | Resistors_SMD:R_0805 | R21, R22, R25, R26 |
| 4 | 2.2k | Resistors_SMD:R_0805 | R23, R24, R27, R28 |
| 4 | 2.5m | Resistors_SMD:R_2512 | R3, R4, R7, R8 |
| 3 | 120 | Resistors_SMD:R_0603 | R12, R15, R16 |
| 3 | 1uF | zmyfootprint:CP_Tantalum_Case-B_EIA-3528-21_Reflow | C14, C24, C25 |
| 2 | 1000uF | zmyfootprint:CAPCITOR_TOT | C28, C29 |
| 2 | 100uH | zmyfootprint:Inductor_SLF10145 | L1, L2 |
| 2 | 20 | Resistors_SMD:R_0603 | R5, R6 |
| 2 | 220uF | zmyfootprint:CAP_polar_220uF | C5, C6 |
| 2 | 25k | Resistors_SMD:R_2512 | R18, R19 |
| 2 | 47uF | zmyfootprint:CP_Tantalum_Case-X_EIA-7343-43_Reflow | C9, C10 |
| 2 | 500 | Resistors_SMD:R_0805 | R17, R20 |
| 2 | BUF634 | TO_SOT_Packages_SMD:TO-263-5_TabPin6 | U1, U2 |
| 2 | LT1363 | Housings_SOIC:SOIC-8_3.9x4.9mm_Pitch1.27mm | U12, U13 |
| 2 | Q_NMOS_GDS | zmyfootprint:PowerMOS | Q1, Q3 |
| 2 | Q_PMOS_GDS | zmyfootprint:PowerMOS | Q2, Q4 |
| 2 | R_POT_TRIM | Potentiometers:Potentiometer_Trimmer_Bourns_3214W | RV1, RV2 |
| 1 | 0.1uF | Capacitors_SMD:C_0805 | C18 |
| 1 | 1.8k | Resistors_SMD:R_0603 | R11 |
| 1 | 10 | Resistors_SMD:R_0603 | R1 |
| 1 | 22pF | Capacitors_SMD:C_0402 | C11 |
| 1 | 2M | Resistors_SMD:R_0805 | R10 |
| 1 | 4.22k | Resistors_SMD:R_0603 | R14 |
| 1 | 4k | Resistors_SMD:R_0805 | R13 |
| 1 | 5.1 | Resistors_SMD:R_0603 | R2 |
| 1 | CONN_01X03 | zmyfootprint:Conn_01X03-3.5mm | P1 |
| 1 | Conn_02x04_Counter_Clockwise | zmyfootprint:Socket_Strip_Straight_2x04_Pitch2.54mm_SMD | J8 |
| 1 | Conn_02x07_Odd_Even | zmyfootprint:14PinConn | J3 |
| 1 | Conn_02x08_Odd_Even | zmyfootprint:16PinConn | J4 |
| 1 | LM337_SOT223 | TO_SOT_Packages_SMD:SOT-223 | U10 |
| 1 | LM337_TO220 | TO_SOT_Packages_THT:TO-220-3_Horizontal | U4 |
| 1 | LM7805 | TO_SOT_Packages_THT:TO-220-3_Horizontal | U7 |
| 1 | LM7905 | TO_SOT_Packages_THT:TO-220-3_Horizontal | U8 |
| 1 | LM7915 | TO_SOT_Packages_THT:TO-220-3_Horizontal | U6 |
| 1 | LT3080 | TO_SOT_Packages_THT:TO-220-5_Horizontal | U3 |
| 1 | OPA388 | Housings_SOIC:SOIC-8_3.9x4.9mm_Pitch1.27mm | U11 |
| 1 | R_Shunt | zmyfootprint:SHR4-3825 | R9 |
| 1 | TL1963A | TO_SOT_Packages_SMD:SOT-223-6 | U9 |
| 1 | uA7815 | TO_SOT_Packages_THT:TO-220-3_Horizontal | U5 |

JQIamo/20A-bipolar-current-source
20A bipolar current source with water cooled sensing resistor

TU-Darmstadt-APQ/RedPitaya-Lockbox
Digital controller for laser frequency stabilization based on the RedPitaya STEMlab 125-14 board

EliMattingly22/Simple_Impedance_Analyzer
A PCB impedance analyzer to measure loads to 100kHz and beyond

TWilmer/canbox_nxp_LPC546xx
A Project for a USB to CAN-FD and 100BaseT1 interface using a LPC546xx





MitchReyno/Electronics-Projects
A collection of various electronics projects I've worked on over the years
It measures 145 × 157 mm and has 4 copper layers, 1.6 mm thick.
99 parts, built around the OPA388ID, BUF634T, LM7805 and LM7905T. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
From the JQIamo/20A-bipolar-current-source repository on GitHub, at the commit this page was made from: the board is Kicad/rear/rear.kicad_pcb and its schematic Kicad/front/file5C76BF00.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Its repository states no licence, so its author keeps all rights: ask JQIamo before reusing the design.