

Otterworks arrow
- Size
- 74 × 146 mm
- Copper layers
- 4
- Thickness
- 1.6 mm
- Parts
- 329
- Nets
- 201
- Pads
- 999
- Tracks, vias
- 4,497, 568
- Pours
- 4
- Routed
- Yes
- KiCad
- KiCad 8.0 (file 20240108)
- Created
- 18 Aug 2024
- Updated
- 23 Oct 2024
Overview
Otterworks arrow is an open-source printed circuit board by JDRobotter, from the JDRobotter/otterworks_arrow repository on GitHub. It is a 4-layer board of 74 × 146 mm with 329 parts on 201 nets, routed with 4,497 tracks and 568 vias.
It is built around the ADP7142AUJZ-3.3-R7, BHI160B and WS2812B-2020, with the BPW34 among its other parts. Its parts include 147 capacitors, 137 diodes, 23 resistors, 3 ICs and 2 connectors. It belongs with the STM32 boards of this library.
Main components
4ADP7142AUJZ-3.3-R7
TSOT-23-5-40℃~+125℃@(Ta) 1 11uVrms 200mA 200mV@(200mA) 3.3V 40V 50uA 88dB@(10kHz) Fixed Over Current Protection、Over Temperature Protection、Soft Start、Enable Positive TSOT-23-5 Voltage Regulators - Linear, Low Drop Out (LDO) Regulators ROHSAnalog DevicesVoltage Regulators - Linear, Low Drop Out (LDO) RegulatorsBHI160B
LGA-24(3x3)-40℃~+85℃ 1.71V~3.6V 16bit 48KB 7uA I2C IMU (accelerometer + gyroscope) Motion event detection X,Y,Z X,Y,Z ±16g ±2000dps LGA-24(3x3) Accelerometers ROHSBosch SensortecAccelerometersWS2812B-2020
SMD,2.2x2mm0.6mA 0.84mm 120us 160mcd 200mcd 2kHz 2mm 2mm 300ns 470.4nm 515.6nm 520mcd 5V 622.5nm 800Kbit/s Built-in power-on reset circuit、Built-in power-on reset circuit、Integrated intelligent reverse connection protection function Top-mount SMD,2.2x2mm RGB LEDs(Built-in IC) ROHSWorldsemiRGB LEDs(Built-In IC)BPW34
插件,P=5.1mm-40℃~+100℃ 215mW 2nA 430nm~1100nm 60V 900nm ±65° 插件,P=5.1mm Photodiodes ROHSVishay IntertechnologyPhotodiodes
Parts
329| Qty | Value | Footprint | References |
|---|---|---|---|
| 145 | 100n | Capacitor_SMD:C_0603_1608Metric | C1, C10, C11, C100, C101, C102, C103, C104, C105, C106, C107, C108, C109, C110, C111, C112 +129 |
| 136 | WS2812B-2020 | LED_SMD:LED_WS2812B_PLCC4_5.0x5.0mm_P3.2mm | D1, D10, D11, D100, D101, D102, D103, D104, D105, D106, D107, D108, D109, D110, D111, D112 +120 |
| 9 | TestPoint | TestPoint:TestPoint_Pad_D1.0mm | TP0, TP1, TP2, TP3, TP4, TP5, TP6, TP7, TP8 |
| 7 | 10k | Resistor_SMD:R_0603_1608Metric | R2, R3, R13, R14, R19, R22, R23 |
| 5 | 0 | Resistor_SMD:R_0603_1608Metric | R1, R10, R11, R12, R17 |
| 4 | 100 | Resistor_SMD:R_0603_1608Metric | R4, R5, R6, R7 |
| 2 | 2.2k | Resistor_SMD:R_0603_1608Metric | R8, R9 |
| 2 | 33k | Resistor_SMD:R_0603_1608Metric | R18, R21 |
| 2 | 5.1k | Resistor_SMD:R_0603_1608Metric | R15, R16 |
| 2 | MountingHole | MountingHole:MountingHole_6mm | H3, H4 |
| 2 | MountingHole_Pad | MountingHole:MountingHole_3.2mm_M3_Pad | H1, H2 |
| 2 | ferrite | Inductor_SMD:L_0603_1608Metric | FB1, FB2 |
| 1 | 10 | Resistor_SMD:R_0603_1608Metric | R20 |
| 1 | 1u | Capacitor_SMD:C_0603_1608Metric | C139 |
| 1 | 470n | Capacitor_SMD:C_0603_1608Metric | C137 |
| 1 | ADP7142AUJZ-3.3 | Package_TO_SOT_SMD:TSOT-23-5 | U1 |
| 1 | BHI160B | LGA24_3x3:LGA-24_3x3mm | U2 |
| 1 | BPW34 | OptoDevice:Osram_DIL2_4.3x4.65mm_P5.08mm | D137 |
| 1 | MMBT2484LT1G | Package_TO_SOT_SMD:SOT-23 | Q1 |
| 1 | PROG | Connector_PinHeader_2.54mm:PinHeader_1x06_P2.54mm_Vertical | J1 |
| 1 | STM32F030K6Tx | Package_QFP:LQFP-32_7x7mm_P0.8mm | U3 |
| 1 | SW_Push | Button_Switch_SMD:SW_Push_1P1T_NO_CK_KSC7xxJ | SW1 |
| 1 | USB_C_Plug_USB2.0 | Connector_USB:USB_C_Receptacle_HRO_TYPE-C-31-M-12 | P1 |
Similar boards
- 2 layers73 × 30 mm

- 2 layers124.5 × 79.2 mm

- 2 layers22.9 × 35.6 mm

- 4 layers70 × 17.5 mm

- 4 layers80 × 49 mm

- 2 layers78 × 61 mm

- 2 layers20 × 108 mm

Midi sync module
lucblender/MIDI-sync-power-dev-board
The MIDI-sync-power-dev-board is a 4hp eurorack module allowing you to get an isolated 5V, 3.3V from LDO, a sync in from 3.5mm jack and either midi input or midi output.
41 parts1MIT - 2 layers88.6 × 69.9 mm

ExpressionController
amonbenson/expad
A four-jack USB MIDI adapter for expression and sustain pedals, built on a Raspberry Pi Pico 2 W. It works out what is plugged into each jack - whichever contact a pedal's wiper is on, and whether it is a potentiometer…
147 partsMIT
Questions
How big is the Otterworks arrow PCB?
It measures 74 × 146 mm and has 4 copper layers, 1.6 mm thick.
What parts does the Otterworks arrow use?
329 parts, built around the ADP7142AUJZ-3.3-R7, BHI160B, WS2812B-2020 and BPW34. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the Otterworks arrow KiCad files?
From the JDRobotter/otterworks_arrow repository on GitHub, at the commit this page was made from: the board is otterworks_arrow.kicad_pcb and its schematic leds.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Can I use the Otterworks arrow design in my own project?
Its repository states no licence, so its author keeps all rights: ask JDRobotter before reusing the design.