4 layers70 × 17.5 mm
2 layers73 × 30 mm
Official repository for MuHack Badge
- Size
- 73 × 30 mm
- Copper layers
- 2
- Thickness
- 1.6 mm
- Parts
- 135
- Nets
- 143
- Pads
- 562
- Tracks, vias
- 1,240, 354
- Pours
- 17
- Routed
- Yes
- KiCad
- KiCad 7 (file 20221018)
- Created
- 26 Oct 2022
- Updated
- 19 Oct 2023
Overview
Badge is an open-source printed circuit board by MrMoDDoM, from the MrMoDDoM/MuHack-Badge repository on GitHub, published under the AGPL-3.0 licence. It is a 2-layer board of 73 × 30 mm with 135 parts on 143 nets, routed with 1,240 tracks and 354 vias.
It is built around the RP2040, ESP32-S3 and BMM150, with the W25Q128JVSIQ, AMS1117-3.3 and BHI160B among its other parts. Its parts include 48 capacitors, 29 resistors, 21 diodes, 9 ICs and 7 switches. It belongs with the lEDs and displays boards and the ESP32 and RP2040 boards of this library.
Main components
9
RP2040
LQFN-56(7x7)12bit 133MHz 30 LQFN-56(7x7) Microcontrollers (MCU/MPU/SOC) ROHSRaspberry PiMicrocontrollers (MCU/MPU/SOC)
ESP32-S3
QFN-56-EP(7x7)-40℃~+105℃ -98.4dBm 150Mbps 2.412GHz~2.484GHz 2.4GHz 21dBm 340mA 3V~3.6V 88mA SPI、USB、UART、ADC、I2C、I2S、PWM WiFi transceiver QFN-56-EP(7x7) RF Transceiver ICs ROHSEspressif SystemsRF Transceiver ICs
BMM150
WLCSP-12(1.6x1.6)-40℃~+85℃ 1.62V~3.6V I2C、SPI ±1.3mT ±2.5mT WLCSP-12(1.6x1.6) 3D Magnetic Sensors ROHSBosch3D Magnetic Sensors
W25Q128JVSIQ
SOIC-8-208mil-40℃~+85℃ 100,000 cycles 120ms@(32KB) 128Mbit 133MHz 1uA 2.7V~3.6V 20 Years 3ms Power-on reset、Hardware write protection、Software write protection、Write enable latch、Absolute write protection SPI SOIC-8-208mil NOR FLASH ROHSWinbondNOR FLASH
AMS1117-3.3
SOT-223-40℃~+125℃ 0.003%Vout 1 1.1V@(800mA) 15V 1A 3.3V 5mA 72dB@(120Hz) Fixed Over Current Protection、Short Circuit Protection、Thermal shutdown Positive SOT-223 Voltage Regulators - Linear, Low Drop Out (LDO) Regulators ROHSAdvanced Monolithic SystemsVoltage Regulators - Linear, Low Drop Out (LDO) Regulators
BHI160B
LGA-24(3x3)-40℃~+85℃ 1.71V~3.6V 16bit 48KB 7uA I2C IMU (accelerometer + gyroscope) Motion event detection X,Y,Z X,Y,Z ±16g ±2000dps LGA-24(3x3) Accelerometers ROHSBosch SensortecAccelerometers
SY6280AAC
SOT-23-5-40℃~+125℃ 1 2.4V~5.5V 80mΩ Active High High Side Switch Overcurrent Protection(OCP)、Over Temperature Protection SOT-23-5 Power Distribution Switches ROHS矽力杰silergyPower Distribution Switches
TP4057
SOT-23-6-40℃~+85℃ 1 25uA 4.24V 4V~6.5V Charging IC Lithium Battery Not supported SOT-23-6 Battery Management ROHSTECH PUBLICBattery Management
WS2812B
5mm X 5mm Surface Mount RGB LED with Intelligent ControlWorldsemiUncategorised
README
Hardware/README.mdMuHack-Badge
Official repository for MuHack Badge
Parts
135| Qty | Value | Footprint | References |
|---|---|---|---|
| 18 | 100n | Capacitor_SMD:C_0402_1005Metric | C2, C5, C6, C12, C13, C14, C15, C16, C17, C18, C21, C24, C25, C26, C29, C42 +2 |
| 15 | 10u | Capacitor_SMD:C_0402_1005Metric | C19, C20, C28, C30, C31, C32, C33, C34, C35, C36, C37, C38, C39, C40, C41 |
| 14 | WS2812B | LED_SMD:LED_WS2812B_PLCC4_5.0x5.0mm_P3.2mm | D1, D2, D3, D4, D5, D6, D7, D8, D9, D10, D11, D12, D13, D14 |
| 7 | 10k | Resistor_SMD:R_0402_1005Metric | R2, R10, R13, R14, R21, R22, R25 |
| 7 | 4.7k | Resistor_SMD:R_0402_1005Metric | R6, R8, R9, R12, R23, R24, R31 |
| 5 | 1u | Capacitor_SMD:C_0402_1005Metric | C9, C10, C11, C23, C27 |
| 4 | 27.4 | Resistor_SMD:R_0402_1005Metric | R17, R18, R19, R20 |
| 4 | LOGO | LOGO | G***, G***, G***, G*** |
| 3 | 1k | Resistor_SMD:R_0402_1005Metric | R1, R7, R32 |
| 3 | 2k | Resistor_SMD:R_0402_1005Metric | R15, R16, R33 |
| 3 | 470 | Resistor_SMD:R_0402_1005Metric | R11, R26, R27 |
| 3 | DNP | Capacitor_SMD:C_0402_1005Metric | C48, C49, C50 |
| 2 | 27p | Capacitor_SMD:C_0402_1005Metric | C3, C4 |
| 2 | 4.7uF | Capacitor_SMD:C_0402_1005Metric | C47, C52 |
| 1 | 100k | Resistor_SMD:R_0402_1005Metric | R30 |
| 1 | 10n | Capacitor_SMD:C_0402_1005Metric | C43 |
| 1 | 10nF | Capacitor_SMD:C_0402_1005Metric | C51 |
| 1 | 12MHz_GND24 | Crystal:Crystal_SMD_3225-4Pin_3.2x2.5mm | Y1 |
| 1 | 2.2uH | Inductor_SMD:L_0805_2012Metric | L1 |
| 1 | 2SC4213 | Package_TO_SOT_SMD:SOT-323_SC-70 | Q2 |
| 1 | 470n | Capacitor_SMD:C_0402_1005Metric | C22 |
| 1 | AMS1117-3.3 | Package_TO_SOT_SMD:SOT-223-3_TabPin2 | U2 |
| 1 | BATT | Connector_JST:JST_PH_B2B-PH-K_1x02_P2.00mm_Vertical | BT1 |
| 1 | BHI160B | BHI160B:Bosch_Sensortec-BHI160B-MFG | U5 |
| 1 | BMM150 | BMM150:Bosch_Sensortec-BMM150-IPC_B | U6 |
| 1 | BOOT_MODE | TS-1184:TS-1187A-B-A-B | SW1 |
| 1 | Button A | TS-1184:TS-1187A-B-A-B | SW6 |
| 1 | Button B | TS-1184:TS-1187A-B-A-B | SW5 |
| 1 | Buzzer | Buzzer_Beeper:Buzzer_Mallory_AST1109MLTRQ | BZ1 |
| 1 | CHRG | LED_SMD:LED_0603_1608Metric | LED7 |
| 1 | Conn_01x12 | Connector_PinSocket_1.27mm:PinSocket_2x16_P1.27mm_Vertical | J5 |
| 1 | Conn_02x15_Counter_Clockwise | Connector_PinSocket_2.54mm:PinSocket_2x13_P2.54mm_Vertical | J4 |
| 1 | D | Diode_SMD:D_SOD-123F | D17 |
| 1 | DNF 10k | Resistor_SMD:R_0402_1005Metric | R3 |
| 1 | DNP | Diode_SMD:D_SMA | D18 |
| 1 | DONE | LED_SMD:LED_0603_1608Metric | LED8 |
| 1 | ESP32-S3 | Espressif:ESP32-S3-WROOM-1 | U7 |
| 1 | ESP_BOOT | TS-1184:TS-1187A-B-A-B | SW4 |
| 1 | ESP_DATA | Connector_USB:USB_C_Receptacle_Palconn_UTC16-G | P2 |
| 1 | ESP_LED1 | LED_SMD:LED_0603_1608Metric | LED4 |
| 1 | ESP_LED2 | LED_SMD:LED_0603_1608Metric | LED2 |
| 1 | ESP_RST | TS-1184:TS-1187A-B-A-B | SW7 |
| 1 | Internal_I2C | Connector_PinHeader_1.27mm:PinHeader_1x03_P1.27mm_Vertical | J6 |
| 1 | LOGO | MyGraphics:logo_BIT_10x11mm | G*** |
| 1 | MuTag_NFC_Antenna | MuHack Badge NFC Antenna:muhack_badge_antenna | A1 |
| 1 | PWR | LED_SMD:LED_0603_1608Metric | LED3 |
| 1 | PWR_N_DATA | Connector_USB:USB_C_Receptacle_Palconn_UTC16-G | P1 |
| 1 | PWR_SWT | Button_Switch_SMD:SW_SPDT_CK-JS102011SAQN | SW9 |
| 1 | RESET | TS-1184:TS-1187A-B-A-B | SW2 |
| 1 | RP2040 | Package_DFN_QFN:QFN-56-1EP_7x7mm_P0.4mm_EP3.2x3.2mm | U4 |
| 1 | SAO_v2 | SAOv2:Simple_Addon_v2-BADGE-2x3 | X1 |
| 1 | ST25DV | ST25DV:SOIC127P600X175-8N | IC2 |
| 1 | SWCLK | TestPoint:TestPoint_Pad_D1.0mm | TP3 |
| 1 | SWD | TestPoint:TestPoint_Pad_D1.0mm | TP4 |
| 1 | SY6280AAC | Package_TO_SOT_SMD:SOT-23-5 | U8 |
| 1 | TP4057 | Package_TO_SOT_SMD:SOT-23-6 | U9 |
| 1 | VCC | TestPoint:TestPoint_Pad_D1.0mm | TP1 |
| 1 | VREF | TestPoint:TestPoint_Pad_D1.0mm | TP2 |
| 1 | W25Q128JVS | Package_SO:SOIC-8_5.23x5.23mm_P1.27mm | U1 |
Similar boards
- 2 layers60 × 70 mm
- 4 layers25.4 × 25.4 mm
Zeo1.2 devboard
zeodotdev/zeo-boards
ESP32-S3 development board with onboard BME280 (temperature, humidity, pressure) and LSM6DS3 (6-axis IMU) sensors. This repo contains the designs, ESP-IDF firmware, and a Python plotter for visualization.
92 parts3 - 4 layers66.4 × 66.4 mm
Rera
fdiwth/tvc-drone
This repository contains the documentation, hardware designs, and source code for a Thrust Vector Control (TVC) drone.
140 parts34GPL-3.0 - 4 layers40 × 55 mm
CopterCat cm4
matveylapin/CopterCat_cm4
Полётный контроллер для стандарта FMU-v6u. Обычно на дронах для программирования устанавливают полётный контроллер, одноплатный компьютер и иногда arduino.
164 parts3Apache-2.0 - 4 layers150 × 100 mm
Zpn devboard
CRImier/MyKiCad
My KiCad boards. Can't be bothered uploading individually anymore, so here you go.
168 parts253GPL-3.0 - 2 layers58.5 × 52 mm
HexaGenMini v1
hTuneSys/hexaGenMini
Open-source USB MIDI-controlled signal generator built with Rust (Embassy) on RP2040 + AD985x DDS for education, labs, and music synthesis.
72 parts5MIT - 2 layers99.1 × 99 mm
XDuinoRail Debug
chatelao/xDuinoRail-Decoder
The friendly decoder development plattform for model railroad tinkers.
170 partsAGPL-3.0
Questions
How big is the Badge PCB?
It measures 73 × 30 mm and has 2 copper layers, 1.6 mm thick.
What parts does the Badge use?
135 parts, built around the RP2040, ESP32-S3, BMM150 and W25Q128JVSIQ. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the Badge KiCad files?
From the MrMoDDoM/MuHack-Badge repository on GitHub, at the commit this page was made from: the board is Hardware/Badge.kicad_pcb and its schematic Hardware/Badge.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Can I use the Badge design in my own project?
Its repository publishes it under the AGPL-3.0 licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).