
OmniStimEvalBoard
Hamza-Anver/OmniStimEvalBoard-Hardware
This is an evaluation board to test operating principles of the OptiStim head unit.

This is an evaluation board to test operating principles of the OptiStim head unit.
OmniStimDriverBoard PCB is an open-source printed circuit board by Hamza-Anver, from the Hamza-Anver/OmniStimDriverBoard-PCB repository on GitHub. It is a 2-layer board with 99 parts on 170 nets.
It is built around the ESP32-S2-MINI-2-N4, CP2102N-A02-GQFN28R and MCP4728-E/UN, with the AMS1117-3.3, GRM155R71A104KA01J and G6K-2F-Y-DC5 among its other parts. Its parts include 31 capacitors, 23 resistors, 9 switches, 6 ICs and 5 diodes. It belongs with the ESP32 boards of this library.
This is an evaluation board to test operating principles of the OptiStim head unit.
Fabricated with JLCPCB in April 2025, designed with KiCAD.
It is designed to use the ESP32 Audio PLL to create a signal between approximately 5MHz to 80MHz. This signal is then conditioned and used to drive an LC tank, where the capacitance can be varied digitally and by the DIP switches.
Future designs will have their capacitance entirely digitally controlled, and be miniaturized.
This board is intended only to test if the ESP32 with this conditioning can successfully drive the LC tank and if the resonance of the tank can be subsequently measured by the ESP32.
[x] - switched varicaps from LXRW19V330-050 to LXRW0YV600-054, for JLC availability [x] - have signal reed relays for coarse capacitance switching
[x] - USB to Serial RX TX swapped [x] - Added RXT and TXT LEDs for serial status [x] - Typo JTAG connector (TDI instead of 3V3) [x] - Missing EN and IO0 on UART breakout added [x] - Added USB C connector using ESP32 USB OTG pins (also changed ADC pin on ESP32) [ ] - added a lot more testpoints
GitHub Commit ID: ace2972b83d641ddb22a6ab950a8797fcb3666a8 Was revision 1
| Qty | Value | Footprint | References |
|---|---|---|---|
| 9 | 0.1uF | easyeda2kicad:C0402 | C204, C401, C402, C602, C603, C607, C608, C701, C1001 |
| 9 | 5.1K | easyeda2kicad:R0603 | R501, R502, R601, R602, R603, R604, R608, R610, R613 |
| 7 | G6K-2F-Y-DC5 | easyeda2kicad:RELAY-SMD_G6K-2F-X-XX | K801, K802, K803, K804, K805, K806, K807 |
| 6 | 10K | Resistor_SMD:R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R201, R401, R402, R609, R611, R612 |
| 6 | 10pF | Capacitor_SMD:C_0603_1608Metric_Pad1.08x0.95mm_HandSolder | C801, C802, C803, C804, C805, C806 |
| 5 | 10uF | Capacitor_SMD:C_0603_1608Metric_Pad1.08x0.95mm_HandSolder | C201, C203, C601, C604, C605 |
| 4 | 68nH | easyeda2kicad:L0603 | L1101, L1102, L1103, L1104 |
| 4 | MountingHole_Pad | MountingHole:MountingHole_2.2mm_M2_ISO14580_Pad_TopBottom | H101, H102, H103, H104 |
| 3 | 150pF | Capacitor_SMD:C_0603_1608Metric_Pad1.08x0.95mm_HandSolder | C810, C811, C812 |
| 3 | 30~60pF | easyeda2kicad:X2SON-4_L0.6-W0.6-P0.40-BL | C704, C705, C706 |
| 3 | 39pF | Capacitor_SMD:C_0603_1608Metric_Pad1.08x0.95mm_HandSolder | C807, C808, C809 |
| 3 | RED LED | easyeda2kicad:LED0805-R-RD | LED601, LED602, LED603 |
| 3 | U.FL-R-SMT-1 | easyeda2kicad:RF-SMD_FRF05002-JSS103M | RF902, RF1102, RF1104 |
| 3 | X.FL-R-SMT-1 | easyeda2kicad:ANT-SMD_XFL-R-SMT-1 | RF901, RF1101, RF1103 |
| 2 | 0 | Resistor_SMD:R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R614, R615 |
| 2 | 1K | Resistor_SMD:R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R607, R1003 |
| 2 | 1N5819WS | Diode_SMD:D_SOD-323 | D601, D1001 |
| 2 | 1uF | easyeda2kicad:C0402 | C202, C606 |
| 2 | Antenna_Loop | TxCoil:Tx_20x20_2t | AE1101, AE1102 |
| 2 | L8050QLT1G | easyeda2kicad:SOT-23-3_L2.9-W1.3-P1.90-LS2.4-BR | Q601, Q602 |
| 2 | OPA690IDBVR | easyeda2kicad:SOT-23-6_L2.9-W1.6-P0.95-LS2.8-BL | U401, U402 |
| 2 | PZ254-2-03-S | easyeda2kicad:HDR-SMD_6P-P2.54-V-M-R2-C3-LS7.5-2 | H601, H602 |
| 2 | TS-1088-AR02016 | easyeda2kicad:SW-SMD_L3.9-W3.0-P4.45 | SW601, SW602 |
| 2 | TYPEC-304YSSW-ACP16 | easyeda2kicad:USB-SMD_TYPEC-304YSSW-ACP16 | USB601, USB602 |
| 2 | TestPoint | TestPoint:TestPoint_Pad_1.0x1.0mm | TP101, TP102 |
| 1 | 1M | Resistor_SMD:R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R1001 |
| 1 | 22.1K | Resistor_SMD:R_0603_1608Metric | R605 |
| 1 | 40K | Resistor_SMD:R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R1002 |
| 1 | 47.5K | Resistor_SMD:R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R606 |
| 1 | AMS1117-3.3 | Package_TO_SOT_SMD:SOT-223-3_TabPin2 | U601 |
| 1 | APLL | TestPoint:TestPoint_Pad_1.0x1.0mm | TP201 |
| 1 | CP2102N-A02-GQFN28R | easyeda2kicad:QFN-28_L5.0-W5.0-P0.50-TL-EP3.3 | U602 |
| 1 | ESP32-S2-MINI-2-N4 | easyeda2kicad:WIFI-SMD_ESP32-MINI-1-N4 | U201 |
| 1 | MCP4728-E/UN | easyeda2kicad:MSOP-10_L3.0-W3.0-P0.50-LS5.0-TL | U501 |

Hamza-Anver/OmniStimEvalBoard-Hardware
This is an evaluation board to test operating principles of the OptiStim head unit.

tiacsys/ecad-coffeecaller
CoffeeCaller. Once a nice office gadget it now evolved to a small development board for the Nordic nRF52840.


etherkit/Si5351AVFO
After any schematic change, run tools/exportdocs.sh (needs KiCad 10 kicad-cli). It rewrites docs/Si5351AVFOschematic.pdf, the netlist, SVGs and docs/erc.rpt.

olegantonov/skywave-sdr
Rádio portátil modular de baixo custo: ESP32-S3, OLED, PTT, HF SDR e expansão VHF/UHF. Em desenvolvimento.

stevel1212-droid/stm32-rtc-climate-controller
Kicad project of an STM32-based board climate controller utilizing an RTC module for time-scheduled environmental reading of temperature/humidity with SHT30 sensor and optional small relay for control.

gustebeast/public-steel-guitar
A pedal steel guitar you can build yourself, from parts anyone can buy.
99 parts, built around the ESP32-S2-MINI-2-N4, CP2102N-A02-GQFN28R, MCP4728-E/UN and AMS1117-3.3. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
From the Hamza-Anver/OmniStimDriverBoard-PCB repository on GitHub, at the commit this page was made from: the board is OmniStimDriverBoard-PCB.kicad_pcb and its schematic OmniStimDriverBoard-PCB.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Its repository states no licence, so its author keeps all rights: ask Hamza-Anver before reusing the design.