
DroneHardware
GiovanniRaseraF/DroneTheory
Tests, Theory, Development of Drone HW and SW + Vespin 1 Hardware

Tests, Theory, Development of Drone HW and SW + Vespin 1 Hardware
DroneHardware is an open-source printed circuit board by GiovanniRaseraF, from the GiovanniRaseraF/DroneTheory repository on GitHub, published under the GPL-3.0 licence. It is a 4-layer board of 36.1 × 36 mm with 52 parts on 78 nets, routed with 483 tracks and 69 vias.
It is built around the STM32F405RGT6, MPU-6000 and B5819W. Its parts include 17 capacitors, 13 connectors, 6 resistors, 3 diodes and 2 ICs. It belongs with the STM32 boards of this library.
Teoria e creazione di Flight Controller
Testing di ArduPilot
| Qty | Value | Footprint | References |
|---|---|---|---|
| 7 | 100n | Capacitor_SMD:C_0402_1005Metric | C4, C5, C6, C7, C8, C315, C316 |
| 7 | Conn_01x03_Female | Connector_PinHeader_1.00mm:PinHeader_1x03_P1.00mm_Vertical | J205, J206, J207, J208, J209, J210, J211 |
| 4 | MountingHole_Pad | MountingHole:MountingHole_3.2mm_M3 | H201, H202, H203, H204 |
| 2 | 12p | Capacitor_SMD:C_0402_1005Metric | C11, C12 |
| 2 | 22 | Resistor_SMD:R_0402_1005Metric | R201, R202 |
| 2 | 2u2 | Capacitor_SMD:C_0603_1608Metric | C1, C3 |
| 1 | +5V | Connector_PinHeader_1.00mm:PinHeader_1x01_P1.00mm_Vertical | J101 |
| 1 | 0u47 | Capacitor_SMD:C_1206_3216Metric | C101 |
| 1 | 10K | Resistor_SMD:R_0402_1005Metric | R1 |
| 1 | 10n | Capacitor_SMD:C_0402_1005Metric | C10 |
| 1 | 16MHz | Crystal:Crystal_SMD_3225-4Pin_3.2x2.5mm | Y1 |
| 1 | 1K | Resistor_SMD:R_0603_1608Metric | R101 |
| 1 | 1K5 | Resistor_SMD:R_0603_1608Metric | R3 |
| 1 | 1u | Capacitor_SMD:C_0402_1005Metric | C9 |
| 1 | 22n | Capacitor_SMD:C_0402_1005Metric | C317 |
| 1 | 250mA | Fuse:Fuse_0603_1608Metric | F101 |
| 1 | 33u | Capacitor_Tantalum_SMD:CP_EIA-1608-08_AVX-J | C102 |
| 1 | 39n | Inductor_SMD:L_0402_1005Metric | L1 |
| 1 | 47 | Resistor_SMD:R_0402_1005Metric | R2 |
| 1 | 4u7 | Capacitor_SMD:C_0603_1608Metric | C2 |
| 1 | 600 @ 600MHz | Inductor_SMD:L_0805_2012Metric | FB101 |
| 1 | B5819W | Diode_SMD:D_SOD-123 | D101 |
| 1 | BATTERY | Connector_PinHeader_1.00mm:PinHeader_1x02_P1.00mm_Vertical | J202 |
| 1 | BLUE | LED_SMD:LED_0603_1608Metric | D1 |
| 1 | Conn_01x06_Male | Connector_Hirose:Hirose_DF52-6S-0.8H_1x06-1MP_P0.80mm_Horizontal | J204 |
| 1 | GND | Connector_PinHeader_1.00mm:PinHeader_1x04_P1.00mm_Vertical | J102 |
| 1 | LM3940IMP-3.3/NOPB | Package_TO_SOT_SMD:SOT-223 | VR101 |
| 1 | LOGO | Footprints:LogoVespin20x17p5 | G*** |
| 1 | MPU-6000 | Sensor_Motion:InvenSense_QFN-24_4x4mm_P0.5mm | U303 |
| 1 | RED | LED_SMD:LED_0603_1608Metric | D102 |
| 1 | STM32F405RGT6 | Package_QFP:LQFP-64_10x10mm_P0.5mm | U1 |
| 1 | SWD_CONN | Connector_PinHeader_1.27mm:PinHeader_2x05_P1.27mm_Vertical_SMD | J203 |
| 1 | SW_SPDT | Button_Switch_SMD:SW_SPST_B3U-1000P | SW1 |
| 1 | USB_B_Micro | Connector_USB:USB_Micro-B_Molex-105017-0001 | J201 |

GiovanniRaseraF/DroneTheory
Tests, Theory, Development of Drone HW and SW + Vespin 1 Hardware

GiovanniRaseraF/DroneTheory
Tests, Theory, Development of Drone HW and SW + Vespin 1 Hardware

GiovanniRaseraF/DroneTheory
Tests, Theory, Development of Drone HW and SW + Vespin 1 Hardware


yagamy4680/drone-study
AUAV-OpenSource/FMUv4-PixRacer is the open hardware design of PixHawk FMUv4. It uses STM32F427 and MPU6000. (github)


pms67/LittleBrain-STM32F4-Sensorboard
STM32F4-based PCB interfacing with a variety of sensors.



amrithHN/stm32f4xx_minimal_dev
stm32f4 minimal dev board with few sensors

It measures 36.1 × 36 mm and has 4 copper layers, 4.69 mm thick.
52 parts, built around the STM32F405RGT6, MPU-6000 and B5819W. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
From the GiovanniRaseraF/DroneTheory repository on GitHub, at the commit this page was made from: the board is DronePCB/5V_DroneHardware/DroneHardware.kicad_pcb and its schematic DronePCB/5V_DroneHardware/Connectivity.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Its repository publishes it under the GPL-3.0 licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).