

Gr25 nodes
GR25 Sensor Nodes
- Size
- 32 × 48.8 mm
- Copper layers
- 4
- Thickness
- 1.6 mm
- Parts
- 48
- Nets
- 60
- Pads
- 191
- Tracks, vias
- 506, 81
- Pours
- 162
- Routed
- Yes
- KiCad
- KiCad 7 (file 20221018)
- Created
- 7 Jul 2024
- Updated
- 11 Mar 2026
Overview
Gr25 nodes is an open-source printed circuit board by Gaucho-Racing, from the Gaucho-Racing/Sensor-Nodes repository on GitHub. It is a 4-layer board of 32 × 48.8 mm with 48 parts on 60 nets, routed with 506 tracks and 81 vias.
It is built around the SN65HVD230D, AP63205WU and AMS1117-3.3. Its parts include 18 capacitors, 6 resistors, 6 diodes, 4 ICs and 4 connectors. It belongs with the STM32 boards of this library.
Main components
3SN65HVD230D
SOIC-8-40℃~+85℃ 1 17mA 1Mbps 370uA 3V~3.6V CAN Transceiver Low-power mode、Wake-up function、ESD protection、Thermal shutdown protection、Bus fault protection、Hot-swap protection SOIC-8 CAN Transceivers ROHSTexas InstrumentsCAN TransceiversAP63205WU
TSOT-23-6-40℃~+85℃@(TA) 1 1.1MHz 22uA 2A 3.8V~32V 5V Buck Built-in Fixed Overcurrent Protection、Light load efficient mode、Cycle-by-cycle current limiting、Hiccup current limiting、EMI optimization (spread spectrum) Step-down type Yes TSOT-23-6 DC-DC Converters ROHSDiodes IncorporatedDC-DC ConvertersAMS1117-3.3
SOT-223-40℃~+125℃ 0.003%Vout 1 1.1V@(800mA) 15V 1A 3.3V 5mA 72dB@(120Hz) Fixed Over Current Protection、Short Circuit Protection、Thermal shutdown Positive SOT-223 Voltage Regulators - Linear, Low Drop Out (LDO) Regulators ROHSAdvanced Monolithic SystemsVoltage Regulators - Linear, Low Drop Out (LDO) Regulators
README
README.mdSensor Node hardware and software for GR25
Hardware
The Hardware is split into a couple of folders and have Kicad projects that relate to the Sensor Nodes. This includes random projects and some hardware that might have been usefull.
Software
Includes software for the Sensor Nodes
Compilation:
To compile and be able to debug the project you need the following:
- CMAKE
- arm-none-eabi-gcc
- openocd
- ninja
- VSCode CMAKE extension
- VSCode Cortex Debug extension
Make sure cmake, arm tolchian, openocd,and ninja are added to path
To check the version run:
- cmake --version
- arm-none-eabi-gcc --version
- openocd --version
- ninja --version
After everything is installed you should be able to follow the VSCode UI to compile and debug.
Parts
48| Qty | Value | Footprint | References |
|---|---|---|---|
| 8 | 100nF | Capacitor_SMD:C_0603_1608Metric | C1, C2, C6, C7, C10, C11, C13, C14 |
| 5 | 220 | Resistor_SMD:R_0603_1608Metric | R1, R2, R4, R5, R6 |
| 5 | LED | Diode_SMD:D_0603_1608Metric | D2, D3, D4, D5, D6 |
| 3 | 22uF | Capacitor_SMD:C_1206_3216Metric | C4, C5, C16 |
| 3 | 4.7uF | Capacitor_SMD:C_0603_1608Metric | C8, C9, C12 |
| 2 | 10pF | Capacitor_SMD:C_0603_1608Metric | C17, C19 |
| 1 | +3.3A | Jumper:SolderJumper-2_P1.3mm_Open_RoundedPad1.0x1.5mm | JP5 |
| 1 | +3.3vS | Jumper:SolderJumper-2_P1.3mm_Open_RoundedPad1.0x1.5mm | JP6 |
| 1 | +5vS | Jumper:SolderJumper-2_P1.3mm_Open_RoundedPad1.0x1.5mm | JP3 |
| 1 | 100R | Inductor_SMD:L_0805_2012Metric | FB1 |
| 1 | 10k | Resistor_SMD:R_0603_1608Metric | R3 |
| 1 | 10uF | Capacitor_SMD:C_0805_2012Metric | C3 |
| 1 | 10uF | Capacitor_SMD:C_0603_1608Metric | C15 |
| 1 | 16MHz | Crystal:Crystal_SMD_3225-4Pin_3.2x2.5mm | Y1 |
| 1 | 1N5819 | Diode_SMD:D_SOD-323_HandSoldering | D1 |
| 1 | 3.3V | Jumper:SolderJumper-2_P1.3mm_Bridged_RoundedPad1.0x1.5mm | JP1 |
| 1 | 4.7u | Inductor_SMD:L_Bourns-SRN4018 | L1 |
| 1 | 5V | Jumper:SolderJumper-2_P1.3mm_Open_RoundedPad1.0x1.5mm | JP2 |
| 1 | AMS1117-3.3 | Package_TO_SOT_SMD:SOT-223-3_TabPin2 | U3 |
| 1 | AP63205WU | Package_TO_SOT_SMD:TSOT-23-6 | U2 |
| 1 | BOOT | Jumper:SolderJumper-2_P1.3mm_Open_RoundedPad1.0x1.5mm | JP7 |
| 1 | Enable if VIO | Jumper:SolderJumper-2_P1.3mm_Open_RoundedPad1.0x1.5mm | JP4 |
| 1 | I02 | Connector_PinHeader_2.54mm:PinHeader_1x18_P2.54mm_Vertical | J3 |
| 1 | IO1 | Connector_PinHeader_2.54mm:PinHeader_1x18_P2.54mm_Vertical | J2 |
| 1 | PWR | Connector_PinHeader_2.54mm:PinHeader_1x03_P2.54mm_Vertical | J4 |
| 1 | SN65HVD230 | Package_SO:SOIC-8_3.9x4.9mm_P1.27mm | U1 |
| 1 | STM32F103C8Tx | Package_QFP:LQFP-48_7x7mm_P0.5mm | U4 |
| 1 | SWD | Connector_PinHeader_2.54mm:PinHeader_1x04_P2.54mm_Vertical | J1 |
More from Gaucho-Racing/Sensor-Nodes
2- 4 layers22.4 × 70.5 mm

- 2 layers22.9 × 79.5 mm

Similar boards
- 6 layers40.6 × 40.5 mm

Flight Controller
desanv01/Flight-Controller-V2
STM32H743 controller: regulated power, signal-only ESC, neutral ArduPilot firmware, manufacturing data and engineering history.
169 partsCERN-OHL-S-2.0 - 2 layers81.3 × 72.9 mm

- 2 layers82.8 × 42.3 mm

TBP
AAPythonCode/TBP
It's summer break, and I want to create something cool! Since I play tennis on a daily basis, I thought of creating something related to it.
33 partsCC0-1.0 - 2 layers94.1 × 63.5 mm

GarageOpener
AshiqAshref/Garage-Door-Opener
Universal Garage Door using BLE (Bluetooth Low Power) running on ESP32 with highest security possible.
42 partsMIT - 4 layers100 × 50 mm

- 4 layers54.5 × 40.8 mm

- 2 layers120 × 102.5 mm

Dsug cctv BOARD
LucasLHenry/spelltwister
This is the third version of the code for the Spelltwister module with CCTV. This version uses the Arduino platform and the RP2040, a chip developed by Raspberry Pi for their RPi Pico board.
251 partsMIT - 2 layers69.9 × 120.5 mm

Questions
How big is the Gr25 nodes PCB?
It measures 32 × 48.8 mm and has 4 copper layers, 1.6 mm thick.
What parts does the Gr25 nodes use?
48 parts, built around the SN65HVD230D, AP63205WU and AMS1117-3.3. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the Gr25 nodes KiCad files?
From the Gaucho-Racing/Sensor-Nodes repository on GitHub, at the commit this page was made from: the board is Hardware/Sensor_Nodes_V1/gr25_nodes.kicad_pcb and its schematic Hardware/Sensor_Nodes_V1/gr25_nodes.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Can I use the Gr25 nodes design in my own project?
Its repository states no licence, so its author keeps all rights: ask Gaucho-Racing before reusing the design.