
Ardumower mega shield svn
Ardumower/ardumower
Develop an open source robotic lawn mower (HW+SW reference platform)

2nd IllustraBot
Illustrabot2 IF Motor Beagle v2 is an open-source printed circuit board by FablabLannion, from the FablabLannion/IllustraBot2 repository on GitHub, published under the GPL-2.0 licence. It is a 2-layer board with 79 parts on 81 nets, routed with 1,127 tracks and 0 vias.
It is built around the JUMPER3. Its parts include 24 resistors, 20 capacitors, 16 connectors, 6 ICs and 6 diodes. It belongs with the robots and motor control boards of this library.
This is a Fablab Lannion project. Purpose is to control a robotic arm over 4G using movments from an android phone.
You can find more info on the wiki
List of directories :
test
| Qty | Value | Footprint | References |
|---|---|---|---|
| 10 | CONN_4 | bornier4 | P1, P2, P3, P4, P5, P6, P7, P10, P11, P12 |
| 8 | 10uF | C1 | C3, C4, C15, C16, C17, C18, C19, C20 |
| 6 | 100nF | C1 | C5, C6, C9, C10, C13, C14 |
| 6 | 100uF | CP4 | C1, C2, C7, C8, C11, C12 |
| 6 | 10kohm | R3 | R1, R2, R3, R4, R10, R12 |
| 6 | 150ohm | R3 | R5, R7, R9, R13, R15, R17 |
| 6 | 47k | R3 | R19, R20, R21, R22, R23, R24 |
| 6 | 82kohm | R3 | R6, R8, R11, R14, R16, R18 |
| 6 | LED | LED-3MM | D1, D2, D3, D4, D5, D6 |
| 6 | NPN | TO92 | Q1, Q2, Q3, Q4, Q5, Q6 |
| 6 | STEPSTICK | Stepstick_footprint | U1, U2, U3, U4, U5, U6 |
| 4 | CONN_1 | 1pin | P13, P14, P15, P16 |
| 2 | CONN_23X2 | SIL-2x23-v1 | P8, P9 |
| 1 | JUMPER3 | SIL-3 | JP1 |

Ardumower/ardumower
Develop an open source robotic lawn mower (HW+SW reference platform)

Teslafly/Dead-OpenBMS-dead
A scalable, open source battery management system






whitebox-labs/tentacle
An arduino shield to host and individually isolate up to 4 Atlas Scientific sensor circuits. Measure pH, conductivity, dissolved oxygen, ORP, temperature
79 parts, built around the JUMPER3. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
From the FablabLannion/IllustraBot2 repository on GitHub, at the commit this page was made from: the board is Kicad/V2/Illustrabot2_IF_Motor_Beagle_v2.kicad_pcb. PCBKit opens the board in the browser, with nothing to install.
Its repository publishes it under the GPL-2.0 licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).