

Alarmshock protofinal
As a chronic deep sleeper, I created AlarmShock to help me wake up on time when standard alarms don't work. The design uses a BMI160 accelerometer and gyroscope to measure wrist movement, an ESP32-S3 MCU, and a DRV2605L…
- Size
- 27 × 45 mm
- Copper layers
- 2
- Thickness
- 1.6 mm
- Parts
- 30
- Nets
- 59
- Pads
- 182
- Tracks, vias
- 339, 38
- Pours
- 2
- Routed
- Yes
- KiCad
- KiCad 10.0 (file 20260206)
- Created
- 20 Oct 2026
- Updated
- 5 Nov 2026
Overview
Alarmshock protofinal is an open-source printed circuit board by Enoch36Yi, from the Enoch36Yi/AlarmShock repository on GitHub. It is a 2-layer board of 27 × 45 mm with 30 parts on 59 nets, routed with 339 tracks and 38 vias.
It is built around the ESP32-S3-WROOM-1-N8, DRV2605LDGS and BMI160, with the USBLC6-2SC6 and XC6220B331MR among its other parts. Its parts include 11 capacitors, 9 resistors, 6 ICs, 2 connectors and 1 switch. It belongs with the ESP32 boards of this library.
Main components
5ESP32-S3-WROOM-1-N8
SMD,25.5x18mm-40℃~+85℃ -98.2dBm 2.4GHz 20.5dBm 355mA 3V~3.6V 95mA Bluetooth5.0 ESP32-S3 Chip On-board PCB Antenna UART、SPI、I2C、I2S、USB SMD,25.5x18mm WiFi Modules ROHSEspressif SystemsWiFi ModulesDRV2605LDGS
VSSOP-10-0.5mm-40℃~+85℃ 1 2V~5.2V 500uA I2C Yes VSSOP-10-0.5mm Brushed DC Motor Drivers ROHSTexas InstrumentsBrushed DC Motor DriversBMI160
LGA-14(2.5x3)-40℃~+85℃ 1.71V~3.6V 10uA 16bit 1KB IMU (accelerometer + gyroscope) Motion event detection、Synchronization and timestamp SPI、I2C X,Y,Z X,Y,Z ±16g ±2000dps LGA-14(2.5x3) Accelerometers ROHSBosch SensortecAccelerometersUSBLC6-2SC6
SOT-23-60.35pF、0.8pF 100nA 150W@8/20us 15V 2 5V 6A@8/20us 6V ESD SOT-23-6 ESD and Surge Protection (TVS/ESD) ROHSUMWESD And Surge Protection (TVS/ESD)XC6220B331MR
SOT-23-5-40℃~+85℃@(Ta) 1 25uA 3.3V 400mV@(800mA) 5.5V 50dB@(10kHz) 900mA Fixed Over Current Protection、Over Temperature Protection Positive SOT-23-5 Voltage Regulators - Linear, Low Drop Out (LDO) Regulators ROHSTECH PUBLICVoltage Regulators - Linear, Low Drop Out (LDO) Regulators
README
README.mdAlarmShock
As a chronic deep sleeper, I created AlarmShock to help me wake up on time when standard alarms don't work. The design uses a BMI160 accelerometer and gyroscope to measure wrist movement, an ESP32-S3 MCU, and a DRV2605L driver for a vibration motor. The goal is a wrist-worn alarm that combines motion sensing with a physical wake-up signal.
This repository contains the PCB design and its supplied fabrication exports. Firmware, Dashboard, and assembled-device test results are not included. Motion-based control and wake-up performance are not verified by the files in this repository.

Some component body models are absent.
Hardware
| Part | Role in this revision |
|---|---|
| ESP32-S3-WROOM-1 | Controller; connected to the motion sensor and haptic driver over I2C |
| BMI160 | Accelerometer and gyroscope for wrist-motion sensing |
| DRV2605L | Haptic driver connected to the external motor header, M1 |
| MCP73831 | Battery charging circuit |
| XC6220B331MR | 3.3 V regulator |
| USB-C and USBLC6-2SC6 | USB connection and data-line ESD protection |
The motion sensor measures acceleration and angular rate; this revision has no heart-rate sensor. It has not been validated for sleep-stage detection. Component references: Bosch BMI160 datasheet and TI DRV2605L.
Open the board
Use KiCad 10 and open KiCad/Alarmshock_protofinal.kicad_pro, then launch the PCB editor. Standard KiCad footprint libraries are required. No schematic was present in the supplied project, so this archive contains the board and its pad/net assignments rather than a complete schematic project.
To repeat the board check:
kicad-cli pcb drc --output DRC-review.rpt KiCad/Alarmshock_protofinal.kicad_pcbCurrent status
A fresh KiCad 10.0.5 check reports 3 warnings and 0 unconnected items. Two warnings concern silkscreen at the board edge; the third is an ESP32-S3 footprint/library mismatch. The report lists the configured ignored checks. See DRC-current.rpt; the supplied older report is preserved as DRC-original.rpt.
The assembly files need reconciliation before ordering: UPLOAD_BOM_no_M1_no_U3.csv and its CPL omit the motor and BMI160, and the board's R4 value is e while the assembly BOM lists 4.7 kOhm. These files are preserved as supplied. Gerbers are existing exports, not a fabrication approval. Battery charging, assembled operation, haptic output and wake-up reliability have not been verified in this review.
Files
KiCad/: editable board, project settings, component list and DRC reports.gerbers/: supplied copper, mask, paste, silkscreen, outline and drill exports.previews/: a 3D JPG exported from the unchanged board.UPLOAD_BOM_no_M1_no_U3.csvandUPLOAD_CPL_no_M1_no_U3.csv: supplied partial assembly files.SHA256SUMS.txt: checksums for the repository files.
The supplied folder had no development Git history to import. Original project files remain unchanged. Personal concept notes and local KiCad preferences are excluded. No license has been added.
Parts
30| Qty | Value | Footprint | References |
|---|---|---|---|
| 5 | 10uF | Capacitor_SMD:C_0603_1608Metric | C1, C2, C3, C4, C5 |
| 4 | 100nF | Capacitor_SMD:C_0603_1608Metric | C8, C9, C10, C11 |
| 3 | 10k | Resistor_SMD:R_0603_1608Metric | R6, R7, R8 |
| 2 | 1uF | Capacitor_SMD:C_0603_1608Metric | C6, C7 |
| 2 | 4.7k | Resistor_SMD:R_0603_1608Metric | R3, R5 |
| 2 | 5.1k | Resistor_SMD:R_0603_1608Metric | R1, R2 |
| 1 | 100k | Resistor_SMD:R_0603_1608Metric | R9 |
| 1 | BMI160 | Package_LGA:Bosch_LGA-14_3x2.5mm_P0.5mm | U3 |
| 1 | BOOT | Button_Switch_SMD:SW_SPST_TL3342 | SW1 |
| 1 | Conn_01x02_Socket | Connector_JST:JST_PH_S2B-PH-SM4-TB_1x02-1MP_P2.00mm_Horizontal | J2 |
| 1 | DRV2605LDGS | Package_SO:TSSOP-10_3x3mm_P0.5mm | U2 |
| 1 | ESP32-S3-WROOM-1 | RF_Module:ESP32-S3-WROOM-1 | U1 |
| 1 | MCP73831-2-MC | Package_DFN_QFN:DFN-8-1EP_3x2mm_P0.5mm_EP1.7x1.4mm | U4 |
| 1 | Motor_DC | Connector_PinHeader_2.54mm:PinHeader_1x02_P2.54mm_Vertical | M1 |
| 1 | USBLC6-2SC6 | Package_TO_SOT_SMD:SOT-23-6 | U6 |
| 1 | USB_C_Receptacle_USB2.0_16P | Connector_USB:USB_C_Receptacle_HRO_TYPE-C-31-M-12 | J1 |
| 1 | XC6220B331MR | Package_TO_SOT_SMD:SOT-23-5 | U5 |
| 1 | e | Resistor_SMD:R_0603_1608Metric | R4 |
Similar boards
- 4 layers38 × 55 mm

- 4 layers66 × 40 mm

ESP32 PRELIM DESIGN
ece49022-team9/slate
Keep the team's native schematic and board sources here, including any project-specific libraries needed to open them.
82 parts - 2 layers310 × 125 mm

- 2 layers69 × 34.5 mm

Lora ch1
0x000f1/lora-ch1
This project is based on the ESP32 microcontroller that behaves like a bridge between mobile devices and the modules.
37 parts - 2 layers40 × 50 mm

- 4 layers50 × 72.5 mm

- 2 layers28.5 × 43.5 mm

ESP32-S3-DevBoard
plutabartek-ai/ESP32-S3-DevBoard
Zadanie rekrutacyjne - projekt płytki PCB dla modułu ESP32-S3
19 parts - 2 layers80.5 × 93.5 mm

Haptic controller copy
rrzhang139/haptic-controller-pcb
Haptic motor controller PCB — ESP32-S3 + 8x DRV2605L + TCA9548A I2C mux
88 parts
Questions
How big is the Alarmshock protofinal PCB?
It measures 27 × 45 mm and has 2 copper layers, 1.6 mm thick.
What parts does the Alarmshock protofinal use?
30 parts, built around the ESP32-S3-WROOM-1-N8, DRV2605LDGS, BMI160 and USBLC6-2SC6. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the Alarmshock protofinal KiCad files?
From the Enoch36Yi/AlarmShock repository on GitHub, at the commit this page was made from: the board is KiCad/Alarmshock_protofinal.kicad_pcb. PCBKit opens the board in the browser, with nothing to install.
Can I use the Alarmshock protofinal design in my own project?
Its repository states no licence, so its author keeps all rights: ask Enoch36Yi before reusing the design.