Berrythe is an open-source printed circuit board by EarthLord, from the EarthLord/Berrythe-Cranberry.Fit repository on GitHub, published under the BSD-3-Clause licence. It is a 4-layer board of 39.1 × 107 mm with 87 parts on 62 nets, routed with 549 tracks and 121 vias.
It is built around the LP5810DDSD, BQ29737DSE and TCR2LF33,LM(CT, with the TP4056, DMN2024UQ and D5V0S1U2LP-7B among its other parts. Its parts include 39 resistors, 14 capacitors, 11 diodes, 5 ICs and 4 connectors.
Create a low-cost alternative for a breathing assistant toy in India by replacing the circuitry of a night light toy. The working is similar these toys in these Amazon US shopping link 1, shopping link 2. Below is a video of the resulting breathing sequence from a retrofit night light toy.
This open-source project is done for Cranberry.fit, a company developing personalized care products to improve menstrual health.
Repository Content
This repository contains both the hardware and firmware for Berrythe - KiCad PCB design and TI Code Composer Studio Project. The respective hardware and firmware folders contain their documentation as well.
Additional cost for the electronics at quantity of 1000 needs to be less than 300 INR.
Battery life
Breathing or Night light mode need needs to be able to run at least for 8 hours on a full charge.
In OFF mode the battery should last at least 6 months.
Operations of the toy
Overall there are three modes for the toy, namely
Power down mode (OFF)
Breathing mode (BREATH)
Yellow night light mode (NIGHT)
There is one button for user input interaction, at the bottom of the toy. The two means of interaction with this button is single-press or double-press. Double press isn’t used as it reduces good user experience.
The breathing mode will be on for a time of 10 minutes, following which it’ll power down.
The night light mode will be on for a time of 30 minutes, following which it’ll power down.
The following will be the flow of operation of the toy
mermaid
stateDiagram
direction LR
[*] --> OFF
OFF --> BREATH:1-press
BREATH --> NIGHT:1-press
BREATH --> OFF:10 min
NIGHT --> OFF:30 min
NIGHT --> OFF:1-press
The breathing mode timing would be as follows to provide an overall 4, 7, 8 breathing exercise. The green and blue color intensity would change as shown below, visually changing linearly.
Inhale
Tr
Hold
Tr
Exhale
Tr
3.8s
0.2s
6.8s
.2s
7.8s
0.2s
During the transition time of 0.2s (Tr in above table) the color will shift from previous one to the next one.
Breathing Technique’s Why and How
Slow, controlled breathing stimulates the parasympathetic nervous system
This is the part of the nervous system that slows down activity in the body, promotes relaxation, and thus alleviates anxiety and mood changes
Slows down heart rate, blood pressure, and oxygen consumption
This breathing technique has a low inhale-to-exhale ratio (where you only inhale for 4 seconds and exhale for 8), and requires you to hold your breath. These specific practices may increase your blood oxygen levels and lower your blood pressure. All of which contribute to a less agitated, and more relaxed state.
Part of the City Scanner project at MIT Senseable City Lab, Flatburn is an open-source, solar-powered, modular sensing platform that can be easily deployed on road vehicles to collect various environmental data.
The Smart Plant is a board that can be plugged directly on the soil, close to the plant, that allows the measurement of the environment (soil moisture, environment temperature & illuminance), and presents the…
It measures 39.1 × 107 mm and has 4 copper layers, 1.6 mm thick.
What parts does the Berrythe use?
87 parts, built around the LP5810DDSD, BQ29737DSE, TCR2LF33,LM(CT and TP4056. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the Berrythe KiCad files?
From the EarthLord/Berrythe-Cranberry.Fit repository on GitHub, at the commit this page was made from: the board is hardware/Berrythe.kicad_pcb and its schematic hardware/Berrythe.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Can I use the Berrythe design in my own project?
Its repository publishes it under the BSD-3-Clause licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).