
CopterCat cm4
matveylapin/CopterCat_cm4
Полётный контроллер для стандарта FMU-v6u. Обычно на дронах для программирования устанавливают полётный контроллер, одноплатный компьютер и иногда arduino.

A small board for controlling two DC fans from an open-drain inverted PWM output.
Pwm fan control is an open-source printed circuit board by Duckle29, from the Duckle29/PWM-to-fan repository on GitHub, published under the MIT licence. It is a 2-layer board of 41.5 × 19 mm with 28 parts on 20 nets, routed with 198 tracks and 76 vias.
It is built around the LM358 and MUN5211DW1. Its parts include 14 resistors, 3 capacitors, 3 transistors, 3 connectors and 2 inductors.
This is a small board intended to take an open-drain inverted PWM output, and convert it to constant current from 0-200mA for a fan. This is because many fans do not run well with their main supply PWMed. The reason to go for Constant current, is to limit the heat wasted in the transistor.
The board was made for use with the Duet 3D printer controllers, but will work for any open-drain inverted PWM outputs.
Many thanks to N2 who came up with the circuit.

| Qty | Value | Footprint | References |
|---|---|---|---|
| 4 | 10k | Resistor_SMD:R_0603_1608Metric_Pad1.05x0.95mm_HandSolder | R1, R7, R13, R14 |
| 2 | 10R | Resistor_SMD:R_1206_3216Metric_Pad1.42x1.75mm_HandSolder | R6, R12 |
| 2 | 1k | Resistor_SMD:R_0603_1608Metric_Pad1.05x0.95mm_HandSolder | R3, R10 |
| 2 | 220k | Resistor_SMD:R_0603_1608Metric_Pad1.05x0.95mm_HandSolder | R2, R8 |
| 2 | 270k | Resistor_SMD:R_0603_1608Metric_Pad1.05x0.95mm_HandSolder | R4, R9 |
| 2 | 330nF | Capacitor_SMD:C_0603_1608Metric_Pad1.05x0.95mm_HandSolder | C2, C3 |
| 2 | 470uH | Inductor_SMD:L_1210_3225Metric_Pad1.42x2.65mm_HandSolder | L1, L2 |
| 2 | 47k | Resistor_SMD:R_0603_1608Metric_Pad1.05x0.95mm_HandSolder | R5, R11 |
| 2 | Q_NMOS_GSD | Package_TO_SOT_SMD:TO-252-2 | Q1, Q2 |
| 1 | 100nF | Capacitor_SMD:C_0603_1608Metric_Pad1.05x0.95mm_HandSolder | C1 |
| 1 | Fan-out0 | Connector:FanPinHeader_1x03_P2.54mm_Vertical | J1 |
| 1 | Fan-out1 | Connector:FanPinHeader_1x03_P2.54mm_Vertical | J3 |
| 1 | LM358 | Package_SO:SOIC-8_3.9x4.9mm_P1.27mm | U1 |
| 1 | LOGO | graphics:kiwi | G*** |
| 1 | MUN5211DW1 | Package_TO_SOT_SMD:SOT-363_SC-70-6 | Q3 |
| 1 | PWM and power | Connector_PinHeader_2.54mm:PinHeader_1x04_P2.54mm_Vertical | J2 |
The 27 most common of 28 parts.

matveylapin/CopterCat_cm4
Полётный контроллер для стандарта FMU-v6u. Обычно на дронах для программирования устанавливают полётный контроллер, одноплатный компьютер и иногда arduino.

t3mschm2d/esp32-tiny-led-controller
The main goal of this project is to develop an OpenHardware board for controlling digital LED strips. The control shall be done via Homeassistant and esphome.The PCB is based around an ESP32-U4WDH microcontroller and…

Benedikt3141/Smart-Irrigation-System
A smart irrigation system for irrigation of up to 6 plants. It monitors the moisture, temperature, CO2 concentration, air quality ... and displays the data on a 2.4" TFT Display using an ESP32 DevKit C as processor.

Samprab06/ESAP-Tetris
Tetris implementation for the ESP32 microcontroller with integrated audio support, TFT display rendering, and SD card file access.

sensslen/Cfg.CameraControl.Hardware
Hardware needed to control a lanc camera with a PTZ head

peterheinrich/InternetOverSpaghetti
Transmitting IP packages over a pair of spaghetti thus demonstrating how media independent IP really is.

zmaker/arduino_cookbook
gli sketch del nuovo progetto Arduino Cookbook e dei video di YouTube

profdc9/RFBitBanger
A QRP digital transceiver created from readily available parts for off-the-grid maintenance
It measures 41.5 × 19 mm and has 2 copper layers, 1.6 mm thick.
28 parts, built around the LM358 and MUN5211DW1. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
From the Duckle29/PWM-to-fan repository on GitHub, at the commit this page was made from: the board is pwm-fan-control.kicad_pcb. PCBKit opens the board in the browser, with nothing to install.
Its repository publishes it under the MIT licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).