
EnvMonitor
kennySzhucheng/EnvMonitor
🌡️ 智能环境监测站 | STM32F103C8T6 + FreeRTOS + ESP8266 | 温湿度/光照/测距/OLED菜单/ThingSpeak上云 | 从裸机到RTOS到KiCad PCB全流程

Réinterprétation électronique du jeu "1, 2, 3 Soleil" : trois stations équipées de capteurs de mouvement surveillent chaque joueur pendant la phase "Soleil" (silence), une LED RGB par joueur indique s'il est encore en…
123Soleil is an open-source printed circuit board by Claclou3012, from the Claclou3012/123soleil_pcb repository on GitHub. It is a 2-layer board of 70 × 100.1 mm with 30 parts on 39 nets, routed with 330 tracks and 82 vias.
It is built around the HC-SR04 and 1N4148WS. Its parts include 5 resistors, 5 diodes, 4 ICs, 2 capacitors and 2 transistors. It belongs with the ESP32 boards of this library.
Réinterprétation électronique du jeu "1, 2, 3 Soleil" : trois stations équipées de capteurs de mouvement surveillent chaque joueur pendant la phase "Soleil" (silence), une LED RGB par joueur indique s'il est encore en jeu ou éliminé, le tout accompagné de musique et affiché sur un écran OLED.
Batterie LiPo ──> Verrouillage (S1 + Q2) ──> XIAO ESP32-S3
├── Écran OLED (I2C) : round / joueurs restants
├── Chaîne de 4 LED RGB adressables (3 joueurs + feu central)
├── Haut-parleur (piloté par Q1) : musique / bruitages
└── 3x capteur HC-SR04 (Trig commun, Echo individuel avec pont diviseur)| Réf | Composant | Rôle |
|---|---|---|
| U1 | XIAO ESP32-S3 | Microcontrôleur |
| J1 | Écran OLED SSD1306 (I2C) | Affichage du jeu |
| U2, U3, U4 | HC-SR04 | Capteurs de mouvement (un par joueur) |
| D1-D3 | LED RGB adressable | Une par joueur |
| D4 | LED RGB adressable | Feu central (rouge/vert) |
| Q1 | NMOS | Pilotage du haut-parleur |
| Q2 | NMOS | Interrupteur à verrouillage (marche/arrêt) |
| S1 | Bouton poussoir | Marche / démarrage |
| LS1 | Haut-parleur | Musique et bruitages |
| J2 | Connecteur JST batterie | Alimentation LiPo |
La liste complète des composants (résistances, condensateurs, diodes) est disponible dans le fichier de schéma.
123Soleil.kicad_pro — fichier projet KiCad123Soleil.kicad_sch — schéma électronique123Soleil.kicad_pcb — circuit imprimé (2 couches, plan de masse séparé sur chaque face)ibom.html



| Qty | Value | Footprint | References |
|---|---|---|---|
| 5 | 1k | Resistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R_A1, R_A2, R_A3, R2, R6 |
| 4 | Inolux_IN-PI554FCH | LED_SMD:LED_Inolux_IN-PI554FCH_PLCC4_5.0x5.0mm_P3.2mm | D1, D2, D3, D4 |
| 3 | 2k | Resistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R_B1, R_B2, R_B3 |
| 3 | HC-SR04 | HC-SR04:XCVR_HC-SR04 | U2, U3, U4 |
| 2 | 100k | Resistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R3, R7 |
| 2 | 10µF | Capacitor_SMD:C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C1, C2 |
| 2 | Q_NMOS_GSD | Package_TO_SOT_SMD:SOT-23-3 | Q1, Q2 |
| 1 | 10k | Resistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R4 |
| 1 | 1N4148WS | Diode_SMD:D_SOD-323 | D5 |
| 1 | 220k | Resistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R8 |
| 1 | 330 | Resistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R1 |
| 1 | Conn_01x02 | Connector_JST:JST_PH_S2B-PH-K_1x02_P2.00mm_Horizontal | J2 |
| 1 | DM-OLED096-636 | OLED:MODULE_DM-OLED096-636 | J1 |
| 1 | SW_Push | Button_Switch_THT:SW_PUSH_6mm_H5mm | SW1 |
| 1 | Speaker | Buzzer_Beeper:Speaker_CUI_CMR-1206S-67 | LS1 |
| 1 | XIAO-ESP32-S3-SMD | Xiao:XIAO-ESP32-S3-SMD | U1 |

kennySzhucheng/EnvMonitor
🌡️ 智能环境监测站 | STM32F103C8T6 + FreeRTOS + ESP8266 | 温湿度/光照/测距/OLED菜单/ThingSpeak上云 | 从裸机到RTOS到KiCad PCB全流程


NikolaiRadke/Noko_2
The do-it-yourself Arduino-based Noko monster. Version 2 with PCB and 3D printed casing.

billtsol/Maze
This project demonstrates how to use an Arduino board, IR sensors, and a motor driver shield to create a maze-solving robot.

c-lydia/ESP-ROS2
A tiny robot with IMU (MPU5060) and an ultrasonic sensor (HC-SR04), running on micro-ROS, communicating over UDP.

dbrgn/crazyflie2-hcsr04
Ultrasonic sensor (HC-SR04) extension board for the Crazyflie 2.0

YousefAliAicha/aegis-embedded-system
Networked rotating ultrasonic radar system built on the Deneyap Kart 1A (ESP32-S3), with a real-time web dashboard served directly from the board.

YousefAliAicha/sentinel-arduino-firmware
Adaptive traffic-light FSM on the Arduino UNO R3 — pedestrian preemption, LDR-gated night mode with HC-SR04 vehicle detection, and a multiplexed 7-segment countdown. Fully non-blocking.
It measures 70 × 100.1 mm and has 2 copper layers, 1.6 mm thick.
30 parts, built around the HC-SR04 and 1N4148WS. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
From the Claclou3012/123soleil_pcb repository on GitHub, at the commit this page was made from: the board is 123Soleil.kicad_pcb and its schematic 123Soleil.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Its repository states no licence, so its author keeps all rights: ask Claclou3012 before reusing the design.