

Wideband v2
O2 Sensor visualizer
- Size
- 50 × 40 mm
- Copper layers
- 4
- Thickness
- 4.69 mm
- Parts
- 111
- Nets
- 96
- Pads
- 384
- Tracks, vias
- 947, 87
- Pours
- 2
- Routed
- Yes
- KiCad
- KiCad 6 (file 20211014)
- Created
- 3 Mar 2022
- Updated
- 20 Aug 2024
Overview
Wideband v2 is an open-source printed circuit board by Churrosoft, from the Churrosoft/OpenEFI-Wideband repository on GitHub, published under the MIT licence. It is a 4-layer board of 50 × 40 mm with 111 parts on 96 nets, routed with 947 tracks and 87 vias.
It is built around the RP2040, TJA1042T-3,118-TD and MCP6004-E/P, with the W25Q128JVSIQ, L7805 and OPA388IDR-TP among its other parts. Its parts include 37 capacitors, 37 resistors, 12 ICs, 7 diodes and 5 connectors. It belongs with the RP2040 boards of this library.
Main components
9RP2040
LQFN-56(7x7)12bit 133MHz 30 LQFN-56(7x7) Microcontrollers (MCU/MPU/SOC) ROHSRaspberry PiMicrocontrollers (MCU/MPU/SOC)TJA1042T-3,118-TD
SOIC-8-40℃~+125℃ 1Mbps 4.5V~5.5V 400nA 70mA CAN Transceiver Low-power mode、Wake-up function、TXD dominant timeout、ESD protection、Undervoltage Protection、Thermal shutdown protection、Bus fault protection、Integrated level shifting、Enable SOIC-8 CAN Transceivers ROHSTDSEMICCAN TransceiversMCP6004-E/P
PDIP-14-40℃~+125℃ 1.8V~6V 100uA 1MHz 1pA 1pA 23mA 28nV/√Hz@1kHz 2uV/℃ 4 4.5mV 600V/ms 76dB ESD protection Rail-to-Rail Input, Rail-to-Rail Output PDIP-14 Operational Amplifier ROHSMicrochip TechnologyOperational AmplifierW25Q128JVSIQ
SOIC-8-208mil-40℃~+85℃ 100,000 cycles 120ms@(32KB) 128Mbit 133MHz 1uA 2.7V~3.6V 20 Years 3ms Power-on reset、Hardware write protection、Software write protection、Write enable latch、Absolute write protection SPI SOIC-8-208mil NOR FLASH ROHSWinbondNOR FLASHL7805
TO-220ST0℃~+125℃@(Tj) 1 1.2A 20V 2V@(1A) 42uV 500uA 5V 73dB@(120Hz) Fixed Positive Short Circuit Protection TO-220ST Voltage Regulators - Linear, Low Drop Out (LDO) Regulators ROHSOSENVoltage Regulators - Linear, Low Drop Out (LDO) RegulatorsOPA388IDR-TP
SOP-8SOP-8 Precision Op Amps ROHSTECH PUBLICPrecision Op AmpsTXS0102DCU
TSSOP82-Bit Bidirectionnal Voltage-Level Translator for Open-Drain and Push-Pull ApplicationsTexas InstrumentsUncategorisedXC6206P332MR
SOT-23-40℃~+85℃@(Ta) 1 1uA 200mA 3.3V 6V Fixed Over Current Protection Positive SOT-23-3L Voltage Regulators - Linear, Low Drop Out (LDO) Regulators ROHSTorex SemiconductorVoltage Regulators - Linear, Low Drop Out (LDO) RegulatorsWSF60N06
TO-252-55℃~+150℃ 1 N-channel 136pF 15mΩ@4.5V 2.578nF 203pF 20W 3V 60A 60V 9nC@4.5V N-Channel TO-252 MOSFETs ROHSWinsok SemiconMOSFETs
README
README.mdOpenEFI-Wideband
O2 Sensor visualizer
Parts
111| Qty | Value | Footprint | References |
|---|---|---|---|
| 10 | 100nF | Capacitor_SMD:C_0603_1608Metric | C11, C12, C13, C14, C15, C18, C19, C21, C22, C23 |
| 10 | 1k | Resistor_SMD:R_0603_1608Metric | R1, R2, R3, R7, R9, R10, R26, R28, R29, R34 |
| 9 | 10k | Resistor_SMD:R_0603_1608Metric | R4, R8, R13, R14, R18, R19, R22, R23, R35 |
| 6 | 100nF | Resistor_SMD:R_0603_1608Metric | C25, C27, C29, C30, C33, C34 |
| 5 | 10uF | Capacitor_SMD:C_1206_3216Metric | C1, C2, C3, C4, C6 |
| 4 | 30pF | Capacitor_SMD:C_0603_1608Metric | C16, C17, C36, C37 |
| 4 | MountingHole | MountingHole:MountingHole_2.2mm_M2 | H1, H2, H3, H4 |
| 3 | 1uF | Resistor_SMD:R_0603_1608Metric | C24, C28, C32 |
| 3 | 2.2uF | Capacitor_SMD:C_0603_1608Metric | C8, C9, C20 |
| 3 | 20k | Resistor_SMD:R_0603_1608Metric | R31, R32, R33 |
| 3 | RED | LED_SMD:LED_0603_1608Metric | D4, D6, D7 |
| 2 | 100k | Resistor_SMD:R_0603_1608Metric | R20, R21 |
| 2 | 12MHz | Crystal:Crystal_SMD_3225-4Pin_3.2x2.5mm | Y1, Y2 |
| 2 | 1uF | Capacitor_SMD:C_0603_1608Metric | C5, C7 |
| 2 | 27R | Resistor_SMD:R_0603_1608Metric | R5, R6 |
| 2 | 27k | Resistor_SMD:R_0603_1608Metric | R24, R27 |
| 2 | 30R | Resistor_SMD:R_1206_3216Metric | R36, R37 |
| 2 | 68k | Resistor_SMD:R_0603_1608Metric | R11, R12 |
| 2 | DAC5571IDBVR | Package_TO_SOT_SMD:SOT-23-6 | U1, U3 |
| 1 | 10 | Resistor_SMD:R_0603_1608Metric | R16 |
| 1 | 1u | Resistor_SMD:R_0603_1608Metric | C31 |
| 1 | 22k | Resistor_SMD:R_0603_1608Metric | R30 |
| 1 | 3.3k | Resistor_SMD:R_0603_1608Metric | R25 |
| 1 | 33nF | Resistor_SMD:R_0603_1608Metric | C26 |
| 1 | 4.7nF | Capacitor_SMD:C_0805_2012Metric | C38 |
| 1 | 4.7uF | Capacitor_SMD:C_0603_1608Metric | C35 |
| 1 | 47 | Resistor_SMD:R_0603_1608Metric | R15 |
| 1 | 61.9 | Resistor_SMD:R_0603_1608Metric | R17 |
| 1 | BLUE | LED_SMD:LED_0603_1608Metric | D3 |
| 1 | BOOTSEL | Jumper:SolderJumper-2_P1.3mm_Open_TrianglePad1.0x1.5mm | JP4 |
| 1 | CF_CONF0 | Jumper:SolderJumper-2_P1.3mm_Open_TrianglePad1.0x1.5mm | JP1 |
| 1 | CF_CONF1 | Jumper:SolderJumper-2_P1.3mm_Open_TrianglePad1.0x1.5mm | JP2 |
| 1 | CF_CONF2 | Jumper:SolderJumper-2_P1.3mm_Open_TrianglePad1.0x1.5mm | JP3 |
| 1 | DISPLAY | Connector_PinHeader_2.54mm:PinHeader_1x04_P2.54mm_Vertical | J1 |
| 1 | D_Schottky | Diode_SMD:D_SMA | D5 |
| 1 | D_TVS | Diode_SMD:D_SMC | D1 |
| 1 | GPIO | Connector_PinHeader_2.00mm:PinHeader_1x10_P2.00mm_Vertical | J2 |
| 1 | GREEN | LED_SMD:LED_0603_1608Metric | D2 |
| 1 | L7805 | Package_TO_SOT_THT:TO-220-3_Vertical | U2 |
| 1 | LSU | Connector_Molex:Molex_Mini-Fit_Jr_5566-12A2_2x06_P4.20mm_Vertical | J3 |
| 1 | MCP2515-xSO | Package_SO:SOIC-18W_7.5x11.6mm_P1.27mm | U11 |
| 1 | MCP6004 | Package_SO:TSSOP-14_4.4x5mm_P0.65mm | U7 |
| 1 | OPA388IDR | Package_TO_SOT_SMD:TSOT-23-5 | U8 |
| 1 | REF3033 | Package_TO_SOT_SMD:SOT-23 | U9 |
| 1 | RP2040 | wideband:RP2040-QFN-56 | U4 |
| 1 | SW_Push | Button_Switch_THT:SW_Tactile_SPST_Angled_PTS645Vx83-2LFS | SW1 |
| 1 | SYM_Hot_Large | OpenEFI-STM32F_rev3:churro_new_v4 | Churrosoft |
| 1 | TJA1042T3118 | Package_SO:HTSOP-8-1EP_3.9x4.9mm_P1.27mm_EP2.4x3.2mm | U12 |
| 1 | TXS0102DCU | Package_SO:VSSOP-8_2.3x2mm_P0.5mm | U6 |
| 1 | Tag connect | Connector:Tag-Connect_TC2030-IDC-NL_2x03_P1.27mm_Vertical | J4 |
| 1 | USB | Connector_PinHeader_2.00mm:PinHeader_1x02_P2.00mm_Vertical | J5 |
| 1 | W25Q128JVS | Package_SO:SOIC-8_5.23x5.23mm_P1.27mm | U5 |
| 1 | WSF60N06 | Package_TO_SOT_SMD:TO-252-2 | Q1 |
| 1 | XC6206P332MR | Package_TO_SOT_SMD:SOT-23 | U10 |
More from Churrosoft/OpenEFI-Wideband
3- 2 layers54.1 × 40 mm

- 2 layers80 × 50 mm

- 2 layers80 × 50 mm

Similar boards
- 4 layers85.4 × 50.1 mm

Dashdashv2
Churrosoft/Dashdash
tablero de instrumentos por can para integrar con OpenEFI, cuando se nos ocurra algo mas original cambiamos el nombre
94 parts1MIT - 4 layers100 × 100 mm

- 4 layers99.9 × 99.3 mm

ΜEFI rev2
Churrosoft/OpenEFI-PCB
Coleccion de PCB y planos recomendados para montar una OpenEFI
169 parts8CERN-OHL-S-2.0 - 2 layers120 × 102.5 mm

Dsug cctv BOARD
LucasLHenry/spelltwister
This is the third version of the code for the Spelltwister module with CCTV. This version uses the Arduino platform and the RP2040, a chip developed by Raspberry Pi for their RPi Pico board.
251 partsMIT - 4 layers19.8 × 50.9 mm

Zigbee air quality monitor
nobodyguy/zigbee_air_quality_monitor_hardware
Opensource HA compatible air quality monitor with CO2, temperature and humidity measurements
35 parts2Apache-2.0 - 2 layers26.5 × 34.4 mm

PicoLoaderNSB
makeo/PicoLoader
A cheap and easy to install modchip for the Nintendo GameCube!
45 parts320GPL-2.0 - 2 layers35.9 × 62.7 mm

Rp2040-memcard
sd2psx/pcb
The PCB must be produced in 0.8mm thickness. Production files are provided under the "Releases" tab. These do not include the through-hole OLED module.
60 parts241 - 4 layers51.4 × 60.6 mm

Gb rp2040 cart
deltabeard/DBGC
A Game Boy cartridge using the Raspberry Pi RP2040 with RTC and MBC support.
67 parts57
Questions
How big is the Wideband v2 PCB?
It measures 50 × 40 mm and has 4 copper layers, 4.69 mm thick.
What parts does the Wideband v2 use?
111 parts, built around the RP2040, TJA1042T-3,118-TD, MCP6004-E/P and W25Q128JVSIQ. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the Wideband v2 KiCad files?
From the Churrosoft/OpenEFI-Wideband repository on GitHub, at the commit this page was made from: the board is pcb/wideband_v2/wideband_v2.kicad_pcb and its schematic pcb/wideband_v1/untitled.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Can I use the Wideband v2 design in my own project?
Its repository publishes it under the MIT licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).