Skip to the content
2 layers75 × 75 mmCheetoTile, the printed circuit board in 3D

an attiny based rgb led tiling system

Size
75 × 75 mm
Copper layers
2
Thickness
1.6 mm
Parts
41
Nets
48
Pads
164
Tracks, vias
652, 139
Pours
5
Routed
Yes
KiCad
KiCad 9.0 (file 20241229)
Created
14 Dec 2025
Updated
14 Dec 2025

Overview

CheetoTile is an open-source printed circuit board by Cheet0sDelet0s, from the Cheet0sDelet0s/cheetoTile repository on GitHub, published under the GPL-3.0 licence. It is a 2-layer board of 75 × 75 mm with 41 parts on 48 nets, routed with 652 tracks and 139 vias.

It is built around the ATTINY1616-MN and WS2812B. Its parts include 25 diodes, 9 connectors, 3 capacitors, 3 resistors and 1 IC. It belongs with the AVR (ATmega, ATtiny) boards of this library.

Main components

2

README

README.md

cheetoTile

an attiny based rgb led tiling system

Parts

41
QtyValueFootprintReferences
25WS2812BLED_SMD:LED_WS2812B_PLCC4_5.0x5.0mm_P3.2mmD1, D2, D10, D11, D12, D13, D14, D15, D16, D17, D18, D19, D20, D21, D22, D23 +9
4Conn_01x01TestPoint:TestPoint_Pad_1.0x1.0mmJ6, J7, J8, J9
3470Capacitor_SMD:C_0805_2012Metric_Pad1.18x1.45mm_HandSolderR1, R2, R3
2Conn_01x04_PinConnector_PinHeader_2.54mm:PinHeader_1x04_P2.54mm_HorizontalJ1, J3
2Conn_01x04_SocketConnector_PinHeader_2.54mm:PinHeader_1x04_P2.54mm_HorizontalJ2, J4
10.1 µFCapacitor_SMD:C_0805_2012Metric_Pad1.18x1.45mm_HandSolderC1
1100µFCapacitor_SMD:C_1206_3216Metric_Pad1.33x1.80mm_HandSolderC2
110µFCapacitor_SMD:C_0805_2012Metric_Pad1.18x1.45mm_HandSolderC3
1ATtiny1616-MPackage_DFN_QFN:VQFN-20-1EP_3x3mm_P0.4mm_EP1.7x1.7mmU1
1Conn_01x07_PinConnector_PinHeader_2.54mm:PinHeader_1x07_P2.54mm_VerticalJ5

Similar boards

  • 2 layers16 × 43 mmNrf24 remote, the printed circuit board in 3D

    Nrf24 remote

    dragonlock2/kicadboards

    Offsite backup for the miscellaneous KiCad boards that don't fit elsewhere

    72 parts14Apache-2.0
  • 4 layers62.1 × 83.8 mmSs main board, the printed circuit board in 3D

    Ss main board

    loopj/short-stack

    World's Smallest Nintendo Wii, using a trimmed motherboard and custom stacked PCBs

    69 parts804
  • 2 layers80 × 50 mmSiliCa, the printed circuit board in 3D

    SiliCa

    19AJ137/SiliCa

    FeliCa®互換カード「SiliCa」

    14 parts47Unlicense
  • 4 layers100 × 68 mmDevKit, the printed circuit board in 3D

    DevKit

    kaminaris/GigaESC

    209 parts47
  • 2 layers56.9 × 23.6 mmHexagon, the printed circuit board in 3D

    Hexagon

    kieraneglin/hexagon-art

    A passive breakout board: two lever-terminal inputs, three JST XH outputs, all six conductors (RX bus, two spares, +12V, GND, +5V) paralleled straight across. No active components, no regulation, nothing to configure.

    24 parts19
  • 4 layers44.5 × 44.5 mmFlashlight, the printed circuit board in 3D

    Flashlight

    engineerbo/flashlight-dev-hw

    This repository contains design files for the development board for a flashlight boost driver. The test firmware can be found in the firmware repository.

    73 parts15MIT
  • 2 layers29 × 36 mmFlux Capacitor Micro Pin Badge, the printed circuit board in 3D

    Flux Capacitor Micro Pin Badge

    hojadurdy/Flux_Capacitor_Micro

    A tiny (36mm x 29mm) pin badge and keychain PCB version of Flux Capacitor featuring 25 animated LEDs that animate to create the “fluxxing” effect.

    48 parts6
  • 4 layers50.3 × 21.5 mmStormbreaker, the printed circuit board in 3D

    Stormbreaker

    VoxelTek/Stormbreaker

    PMS companion board for Thundervolt.

    49 parts4

Questions

How big is the CheetoTile PCB?

It measures 75 × 75 mm and has 2 copper layers, 1.6 mm thick.

What parts does the CheetoTile use?

41 parts, built around the ATTINY1616-MN and WS2812B. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the CheetoTile KiCad files?

From the Cheet0sDelet0s/cheetoTile repository on GitHub, at the commit this page was made from: the board is pcb/cheetoTile.kicad_pcb and its schematic pcb/cheetoTile.kicad_sch. PCBKit opens the board in the browser, with nothing to install.

Can I use the CheetoTile design in my own project?

Its repository publishes it under the GPL-3.0 licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).