Skip to the content
4 layers90 × 98 mmConvention badge pcb v2, the printed circuit board in 3D

Convention badge pcb v2

BrandonFors/convention_pcb_badge

Design for a custom pcb badge for opensauce convention and maybe other conventions in the future.

Size
90 × 98 mm
Copper layers
4
Thickness
1.6 mm
Parts
57
Nets
42
Pads
210
Tracks, vias
398, 58
Pours
4
Routed
Yes
KiCad
KiCad 9.0 (file 20241229)
Created
25 May 2026
Updated
27 Jul 2026

Overview

Convention badge pcb v2 is an open-source printed circuit board by BrandonFors, from the BrandonFors/convention_pcb_badge repository on GitHub. It is a 4-layer board of 90 × 98 mm with 57 parts on 42 nets, routed with 398 tracks and 58 vias.

It is built around the ESP32-C3-WROOM-02-H4, DW01A and FS8205A, with the TLV75733PDBV, TP4056 and AO3401A among its other parts. Its parts include 13 resistors, 12 capacitors, 6 diodes, 6 switches and 5 ICs. It belongs with the lEDs and displays boards and the ESP32 and RISC-V boards of this library.

Main components

7

README

README.md

Convention Badge Project

The Idea

To create a custom and interactive badge for conventions. The badge would have at least a display and a lipo power supply and some cool designs on the pcb. It would also probably have buttons for interactivity and other fun things.

Design

ESP32C3 microcontroller. PCB designed in KiCad. Programming done with espressif

V1

This design features a basic form factor supporting the XIAO esp32c3 devboard along with a 2.9 inch display module. The design was never actually manufactured.

V2

The V2 board was designed to serve as both a badge and a dev board. It hosts the esp32c3, has support for USB power and flashing, has a battery managment circuit, and various peripherals. The display circuitry still lies on a breakout board which is attached through header pins. It is designed to resemble a satelite.

This design experience was particularly new/challenging because it was the first PCB design I made where I had to consider how parts and integrated circuits interact rather than wiring pin headers together. I also had to consider manufacturing requirements, part availability, and cost.

After manufacturing this board through JLCPCB, I was able to flash the ESP32C3 over USBC and get my display, buttons, and leds working. However, there were a few mistakes within the battery managment circuit that made LiPo power unusable for this version. I was able to fix one to get battery charging working, but a misconfigured mosfet connection made powering the uC with the battery impossible without some reworking which I don't have the tools for.

Code at this stage is pretty scrappy as the main focus was on PCB design and just getting a prototype working.

Overall, I consider this version great progress and a great step towards improving my PCB design skills. Even though the main complexity of the battery managment circuitry doesn't work, I know what to fix in my next revision. This was my first project where programming wasn't really the main focus and I feel that I have a solid understanding of what to expect the design process to look like in my next KiCad project.

V3

Not Started.

This version will ideally look more like a sattelite or whatever form factor represents my interests. It also may switch to a digital display to enable more interactivity than an e-ink offers.

Things that I had to rework/need to be fixed from V2:

  • N-Mosfet for power source switching must align with datasheet
  • Bulk capacitor added to display's power and GND.
  • S1 on FS8205A must be connected to ground.
  • Make lanyard hole a little smaller.
  • Research general rules on where to put bulk/decoupling capacitors in a design and what type of capacitors are needed in various scenarios.

KiCad

All relevant kicad files can be found in convention_badge_kicad. We'll probably start by designing a basic board that would just serve as a platform for the esp32-c3 xiao and an e-paper breakoutboard with pin headers. After that, we can scale up complexity and embed the uC on the pcb badge and choose whether or not to design the badge with an FCC connection.

One reference we are using is Notre Dame's build-a-board workshop pcb design which features a working esp32-c3 breakout board design.

Build-A-Board Credits: https://engineering.nd.edu/news/electrical-engineering-students-create-circuit-boards-in-inaugural-build-a-board-workshop/

Design Notes

Everything below here is scattered notes from my dev process.

Display options

ESP32C3

Datasheet (contains schematics): https://documentation.espressif.com/esp32-c3-wroom-02_datasheet_en.pdf

  • could go with xiao module as a backup
  • could break out all available gpios to exposed vias to double as a breakout board for future use

2.13 inch e-Paper Display Module

https://www.buydisplay.com/black-2-13-inch-e-paper-122x250-display-module-for-arduino-raspberry-pi

Datasheet: https://www.buydisplay.com/download/manual/ER-EPD0213-2-5076_Datasheet.pdf

UC8251 Controller: https://www.buydisplay.com/download/ic/UC8251.pdf

  • is a breakout board and would be good for development on a breadboard.
  • has mounting holes that would be easy to use for the badge
  • tutorial exists online for developing an entire display driver for this specific board.

The raw pannel: https://www.buydisplay.com/graphic-2-13-inch-122x250-electronic-paper-display-manufacturers

2.9 inch e-Paper Display Module

  • probably the best considering size and scalability

https://www.buydisplay.com/black-2-9-inch-e-paper-display-module-for-arduino-raspberry-pi#

Datasheet: https://www.buydisplay.com/download/manual/ER-EPD029-2-5073_Datasheet.pdf

SSD1680 Controller: https://www.buydisplay.com/download/ic/SSD1680.pdf

  • development board that is slightly larger and probably better for display purposes
  • option for a breakout board and raw board if we decide to integrate pannel regulation into badge

The raw pannel: https://www.buydisplay.com/serial-2-9-inch-e-paper-screen-128x296-for-electronic-shelf-label-lcd

2.6 inch e-Paper Display Pannel

https://www.buydisplay.com/2-6-inch-e-ink-152x296-e-paper-display-panel-red-white-black-spi

Datasheet: https://www.buydisplay.com/download/manual/ER-EPD026A1-1_Datasheet.pdf

SSD1675A Controller: https://www.buydisplay.com/download/ic/SSD1675A.pdf

FCC Cable: https://www.buydisplay.com/download/connector/ER-CON24HT-1.pdf

  • doesn't have breakout board
  • slightly larger
  • requires 24 pin fcc ribbon cable and a connector

Manufacturing

Most likely JLCPCB

Will likely have to pay for at least partial assembly.

Price Estimate

Claude session resulted in price estimate of ~$32 per board including assembly and shipping on an order of 5.

To minimize price, we can design a one sided board (the back) and hand solder buttons and attach the scren on the front. I don't think that prevents solder mask designs on the front.

Design Notes

PCB_BadgeV1

This board will utilize the XIAO ESP32 C3 and an 2.9 inch e-Paper Display Module for functionality. Both will be soldered to the badge using header pins. A 3.7V lipo battery will be soldered to the underside of the xiao module as I don't have a way to solder the pads directly to the badge board. The board will also have some buttons on remaining usable gpio pins.

This board is largely complete and contains support for a 2.9 inch epaper breakout and and esp32 c3 xiao soldered to the board using male header pins. One pin is wired to a voltage divider for battery power readings. The board also has support for 3 standard 6mm buttons which use internal pull up resistors on the esp32-c3. Footprints are mostly for through hole breadboard components purely because I am not space constrained and wanted to design the board for components that I already had on hand to avoid shipping/assembly costs.

The odds are that this board is never manufactured just because the next one will feature more peripherals as it won't be constrained by the pinout of the xiao. V2 will support the esp32-c3 directly on the pcb, based largely on the Build-A-Board pcb mentioned above.

Note: This board does not have decoupling capacitors between the e paper display and the 3.3V xiao supply.

Notable Resources

XIAO Getting Started: https://wiki.seeedstudio.com/XIAO_ESP32C3_Getting_Started/

Display Datasheet: Datasheet: https://www.buydisplay.com/download/manual/ER-EPD029-2-5073_Datasheet.pdf

PCB_BadgeV2

This board will be 4 layers with support for the esp32-c3 directly on the pcb. Whether or not the board supports the e-paper display directly with no breakout is TBD. I might opt for a hybrid board that supports both the breakout board and the raw screen with solder bridges to enable/disable either set of connections.

Section 13 of the SSD1680 Datasheet has a diagram of exactly what the 24 pin connector should be wired to.

10k PU with a 1uF capacitor on the EN line creates a RC time constant of 10ms, allowing EN to stay low on to 3.3V stabalizes so the chip boots properly.

I need some way to handle the battery managment of this design. I think I might need a battery charging IC.

Need to make sure that parts are in stock in jlcpcb

https://jlcpcb.com/parts

Going to create a charging/bms circuit using:

  • TP4056
  • DW10A
  • FS8205A

Then I can use TLV75733P for voltage regulation and hook everything to the output 3.3V from there.

Added breakout pins for debugging purposes

Main section is 54 tall and 90 wide -> top and bottom pannels can be 19 tall w/ 3mm gaps between board and pannels

Hex design is 17.5mm tall and 88.1 mm wide

Code Development

Notable E-Paper Sections:

  • 9: Operation Flow
  • 8: Command Description
  • 12.1: Timing table and diagram

Using EastRising's example code and the SD1680 documentation, I've got a working program that prints out an example image onto the screen. The display is electronically configured to be used vertically, but horizontal use is easily fixed with some clever frame buffer software. I'm just going to make it cycle through preconfigured bitmaps with the buttons to control the cycle.

Bitmap Img Converter: https://javl.github.io/image2cpp/

LUT Experiment Notes: Refresh by default is pretty slow at 1.5 sec

  • May be able to cut down with custom lut -> tradeoff is quality bc OTP lut does a full cycle on all pixels to fully clear them Custom lut provided by east rising results in 0.9 sec refresh but leaves a faded img of the previous frame

In the future I can diff two frame buffers to find the changed pixels/sections and then use the xram and yram start/end points to selectively update the screen to avoid some of the anoying refresh.

Parts

57
QtyValueFootprintReferences
8LOGOLOGOG***, G***, G***, G***, G***, G***, G***, G***
61kPCM_JLCPCB:R_0603R5, R6, R9, R11, R12, R13
40.1uFCapacitor_SMD:C_0603_1608MetricC2, C5, C9, C11
310kResistor_SMD:R_0805_2012MetricR3, R4, R10
310uFPCM_JLCPCB:C_CASE-A-3216-18(mm)C3, C4, C10
3SW4X2PCM_JLCPCB:SW-SMD_4P-L5.1-W5.1-P3.70-LS6.5-TL-2SW1, SW2, SW6
3SW_PushButton_Switch_THT:SW_PUSH_6mmSW3, SW4, SW5
2100uFPCM_JLCPCB:C_CASE-B-3528-21(mm)C7, C12
22.2uFCapacitor_SMD:C_0603_1608MetricC6, C8
25.1kPCM_JLCPCB:R_0603R1, R2
2Conn_01x07_PinConnector_PinHeader_2.54mm:PinHeader_1x07_P2.54mm_VerticalJ4, J5
2LEDLED_THT:LED_D5.0mmD4, D5
2RED_LEDPCM_JLCPCB:D_0603D2, D7
1100PCM_JLCPCB:R_0603R8
11uFCapacitor_SMD:C_0603_1608MetricC1
12.2kPCM_JLCPCB:R_0603R7
13.7V BatteryConnector_JST:JST_PH_S2B-PH-K_1x02_P2.00mm_HorizontalJ3
1AO3401APackage_TO_SOT_SMD:SOT-23Q1
1Conn_01x03_PinConnector_PinHeader_2.54mm:PinHeader_1x03_P2.54mm_VerticalJ2
1DW01APackage_TO_SOT_SMD:SOT-23-6U4
1EPaper Breakout2_Displays:2.9_e_paper_ER-EPD029-2-5073DISP1
1ESP32-C3-WROOM-02RF_Module:ESP32-C3-WROOM-02U1
1FS8205APackage_TO_SOT_SMD:SOT-23-6U2
1SS14PCM_JLCPCB:D_DO-214AC(SMA)D3
1TLV75733PDBVPackage_TO_SOT_SMD:SOT-23-5U5
1TP4056PCM_JLCPCB:ESOP-8_L4.9-W3.9-P1.27-LS6.0-BL-EPU3
1USBCConnector_USB:USB_C_Receptacle_GCT_USB4105-xx-A_16P_TopMnt_HorizontalJ1
1YEL_LEDPCM_JLCPCB:D_0603D1

More from BrandonFors/convention_pcb_badge

2
  • 2 layers68.5 × 25.4 mmC3revK7USB, the printed circuit board in 3D

    C3revK7USB

    BrandonFors/convention_pcb_badge

    Design for a custom pcb badge for opensauce convention and maybe other conventions in the future.

    38 parts
  • 2 layers92 × 70 mmConvention badge pcb, the printed circuit board in 3D

    Convention badge pcb

    BrandonFors/convention_pcb_badge

    Design for a custom pcb badge for opensauce convention and maybe other conventions in the future.

    19 parts

Similar boards

  • 2 layers150 × 40 mmBicopter, the printed circuit board in 3D

    Bicopter

    InputBlackBoxOutput/Bicopter

    Design files for a PCB Bicopter

    79 parts1MIT
  • 4 layers38 × 65 mmFelineWatchdog, the printed circuit board in 3D

    FelineWatchdog

    Paschalis/FelineWatchdog

    An ESP32-based system to alert you when your cat goes missing. Monitors Wi-Fi connection between your cat's collar-mounted ESP32 device and an embedded system.

    33 partsGPL-3.0
  • 2 layers78 × 37 mmAkku 3V3 Versorgung, the printed circuit board in 3D

    Akku 3V3 Versorgung

    yvolodym/18650-3v3-supply

    KiCad: stabile 3,3-V-Versorgung aus 18650-Li-Ion-Akku – TP4056-Ladung, DW01A/FS8205A-Schutz, MT3608-Boost, AP2112K-LDO

    32 partsCERN-OHL-S-2.0
  • 2 layers35 × 100 mmWalkieTalkie, the printed circuit board in 3D

    WalkieTalkie

    GuzziFlipFlops/ESP32-Walkie-Talkie

    An open source ESPNOW based walkie talkie with a 600 meter tested distance, with an OLED and multiple buttons to interact with

    66 parts7MIT
  • 2 layers151 × 95 mmDeneme, the printed circuit board in 3D

    Deneme

    g210101021/OpenStylophone-RP2040

    Overview • Technical Summary • Architecture • Hardware Audit & Remediation • Schematic Subsystems • PCB Layout • Firmware Roadmap • Bill of Materials • Author

    143 parts
  • 2 layers50 × 35 mmController module, the printed circuit board in 3D

    Controller module

    InputBlackBoxOutput/INGAME

    Virtual reality controller for playing FPS games

    73 partsMIT
  • 2 layers62 × 6 mmTableLight, the printed circuit board in 3D

    TableLight

    jonny190/TableLight

    A 3D-printable, battery-powered, USB-C rechargeable table lamp in the classic "Poldina" shape - honeycomb disc base, thin stem, down-firing cone shade with a white top - running WLED on an ESP32, with a capacitive touch…

    72 partsMIT
  • 4 layers32.4 × 40.2 mmSmartwatch, the printed circuit board in 3D

    Smartwatch

    Pedro-Seixas/Smartwatch

    A custom-designed smartwatch built around the ESP32-S3, combining BLE connectivity, a rectangular touch display, recharge capability, IMU and temperature sensors. Designed from the ground up in KiCad.

    55 partsMIT

Questions

How big is the Convention badge pcb v2 PCB?

It measures 90 × 98 mm and has 4 copper layers, 1.6 mm thick.

What parts does the Convention badge pcb v2 use?

57 parts, built around the ESP32-C3-WROOM-02-H4, DW01A, FS8205A and TLV75733PDBV. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the Convention badge pcb v2 KiCad files?

From the BrandonFors/convention_pcb_badge repository on GitHub, at the commit this page was made from: the board is convention_badge_kicad/convention_badge_pcb_v2/convention_badge_pcb_v2.kicad_pcb and its schematic convention_badge_kicad/BuildABoard/C3revK7USB.kicad_sch. PCBKit opens the board in the browser, with nothing to install.

Can I use the Convention badge pcb v2 design in my own project?

Its repository states no licence, so its author keeps all rights: ask BrandonFors before reusing the design.