
B VNH5019ATR W ENC ELITE BRK R1.0
Boardoza/Boardoza_VNH5019ATR_w-Enc_Elite_Breakout_Board
High-power H-bridge motor driver breakout board based on STMicroelectronics VNH5019A-E with integrated encoder interface and thermal heatsink design.

B-VNH5019-BRK is a high-current full H-bridge motor driver module based on the VNH5019A-E for 5.5V–24V DC motor control.
B VNH5019-BRK R1.0 is an open-source printed circuit board by Boardoza, from the Boardoza/Boardoza_VNH5019_H_Bridge_Motor_Driver_Module repository on GitHub, published under the CC-BY-SA-4.0 licence. It is a 4-layer board of 80 × 40 mm with 22 parts on 20 nets, routed with 99 tracks and 313 vias.
It is built around the VNH5019ATR-E and BUK962R5-60E,118-VB. Its parts include 11 resistors, 4 capacitors, 3 connectors, 1 IC and 1 transistor. It belongs with the robots and motor control and interfaces and adapters boards of this library.
The Boardoza VNH5019 is a high-current H-Bridge DC motor driver module based on the STMicroelectronics VNH5019A-E full-bridge motor driver IC. Designed for demanding automotive and industrial applications, this board integrates dual high-side and two low-side MOSFET switches using ST’s proprietary VIPower® M0 technology, delivering high efficiency, robust protection, and reliable motor control.
With support for PWM control up to 20 kHz and integrated current sensing, this module is ideal for robotics, automation systems, battery-powered vehicles, smart mobility projects, and industrial motor control applications where high current and protection features are essential.
| Front Side | Back Side |
|---|---|
![]() | ![]() |
Model: VNH5019
Manufacturer: Boardoza
Manufacturer IC: STMicroelectronics
Functions: Full H-Bridge DC Motor Driver
Input Voltage (VIN): 5.5V – 24V DC
Continuous Output Current: 12A
Peak Output Current: 30A (non-repetitive)
Logic Input Compatibility: 3V3 CMOS compatible
PWM Frequency: Up to 20 kHz
Current Sense Ratio: Proportional analog output
Operating Temperature: -40°C to +150°C
Board Dimensions: 80mm x 40mm
| Pin Number | Pin Name | Description |
|---|---|---|
| 1 | VCC | Internally connected to VIN. Used for reverse battery protection. Leave open unless bypassing protection. |
| 2 | PWM | PWM input (CMOS compatible) |
| 3 | INB | Counter-clockwise control input (CMOS compatible) |
| 4 | ENB | Status output for half-bridge B (open-drain, pull-up to VDD required) |
| 5 | VDD | Pull-up supply for ENA/ENB (CMOS/TTL compatible) |
| 6 | CS | Current sense output (proportional to motor current) |
| 7 | ENA | Status output for half-bridge A (open-drain, pull-up to VDD required) |
| 8 | INA | Clockwise control input (CMOS compatible) |
| 9 | GND | Ground |
| 10 | GND | Ground |
| Pin Number | Pin Name | Description |
|---|---|---|
| 1 | OUTB | Motor output B (High-side source / Low-side drain) |
| 2 | OUTA | Motor output A (High-side source / Low-side drain) |
| Pin Number | Pin Name | Description |
|---|---|---|
| 1 | VIN | Power input (5.5V – 24V DC) |
| 2 | GND | Ground |
This repository contains both hardware and software components:
All hardware design files are licensed under Creative Commons Attribution-ShareAlike 4.0 International License.
All software and firmware are licensed under BSD 3-Clause License.
| Qty | Value | Footprint | References |
|---|---|---|---|
| 6 | 1K | Resistor_SMD:R_0603_1608Metric | R3, R4, R5, R6, R7, R11 |
| 3 | 10K | Resistor_SMD:R_0603_1608Metric | R8, R9, R10 |
| 2 | 100nF | Capacitor_SMD:C_0603_1608Metric | C3, C4 |
| 2 | Conn_01x02_Pin | Connector_PinHeader_2.54mm:PinHeader_1x02_P2.54mm_Vertical | J2, J3 |
| 1 | 33nF | Capacitor_SMD:C_0603_1608Metric | C1 |
| 1 | 4,7K | Resistor_SMD:R_0603_1608Metric | R2 |
| 1 | 4.7K | Resistor_SMD:R_0603_1608Metric | R1 |
| 1 | 47UF | Capacitor_SMD:CP_Elec_6.3x7.7 | C2 |
| 1 | Conn_01x10_Pin | Connector_PinSocket_2.54mm:PinSocket_1x10_P2.54mm_Vertical | J1 |
| 1 | NMOS | Package_TO_SOT_SMD:TO-263-2 | Q1 |
| 1 | VNH5019ATR-E | VNH5019ATR-E:IC_VNH5019ATR-E | U1 |
The 20 most common of 22 parts.

Boardoza/Boardoza_VNH5019ATR_w-Enc_Elite_Breakout_Board
High-power H-bridge motor driver breakout board based on STMicroelectronics VNH5019A-E with integrated encoder interface and thermal heatsink design.


Accessibilita/recline-controls
Hardware project for open source wheel chair recline control electronics



senrobo/open
. │ ├── l1 │ ├── 3dmodels │ │ ├── .DSStore │ │ ├── 0603Inductor.step │ │ ├── 1040Inductor.step │ │ ├── ALS-PT19.step │ │ ├── C0603.step │ │ ├── CAPPRD750W80D1600H2500.stp │ │ ├── CD74HC4067M.step │ │…

vyrubaev/TV-Lift-Controller
TVLift Controller is an intelligent controller for TV lift and lower mechanisms, based on the ESP32 microcontroller.

It measures 80 × 40 mm and has 4 copper layers, 1.6 mm thick.
22 parts, built around the VNH5019ATR-E and BUK962R5-60E,118-VB. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
From the Boardoza/Boardoza_VNH5019_H_Bridge_Motor_Driver_Module repository on GitHub, at the commit this page was made from: the board is hardware files/B-VNH5019-BRK-R1.0.kicad_pcb and its schematic hardware files/B-VNH5019-BRK-R1.0.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Its repository publishes it under the CC-BY-SA-4.0 licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).