
VNH5019ATR-E
STMicroelectronicsExtended
-40℃~+150℃ 10uA 18mΩ 30A 5.5V~24V 70A Yes MultiPowerSO-30 Brushed DC Motor Drivers ROHS
- Part id
- st/VNH5019ATR-E
- Category
- Brushed DC Motor Drivers
- Package
- MultiPowerSO-30
- Pins
- 33
- In stock
- 834 at JLCPCB (C2653552)
- Used on
- 9 open-source boards
Overview
The VNH5019ATR-E is a brushed DC Motor Driver made by STMicroelectronics in a MultiPowerSO-30 package with 33 pins. -40℃~+150℃ 10uA 18mΩ 30A 5.5V~24V 70A Yes MultiPowerSO-30 Brushed DC Motor Drivers ROHS.
PCBKit's library has its KiCad symbol (EasyEDA_Cloud:VNH5019ATR-E, from EasyEDA) and its footprint (EasyEDA_Cloud:MULTIPOWERSO-30_L17.2-W16.0-P1.00-LS19.0-BL, from EasyEDA), ready for a KiCad board. 834 are in stock at JLCPCB (part C2653552). 9 open-source boards in 8 repositories on GitHub use it.
Symbol
Footprint
From the datasheet
12- Supply, least
- 5.5 V · VCC, recommended operating min · p. 11
- Supply, most
- 24 V · VCC, recommended operating max · p. 11
- Supply, absolute maximum
- 41 V · VCC, absolute max bridge supply · p. 9
- Junction, hottest
- 150 °C · junction operating max · p. 11
- Takes working
- 4 mA · VCC, typical ON-state, INA or INB = 5 V, no PWM · p. 11
- Takes at most
- 8 mA · VCC, max ON-state, INA or INB = 5 V, PWM = 20 kHz · p. 11
- Takes asleep
- 10 µA · VCC, typical standby, inputs = 0, Tj = 25 °C, VCC = 13 V · p. 11
- Gives
- 30 A · max continuous output current · p. 9
- Current limit
- 50 A · typical high-side current limitation · p. 12
- Junction to case (MultiPowerSO-30)
- 1.7 K/W · max junction-case HSD · p. 10
- Junction to case (MultiPowerSO-30)
- 3.2 K/W · max junction-case LSD · p. 10
- Edge
- 1 µs · typical LSD rise time, VCC = 13 V, RLOAD = 0.87 Ω, Tj = 25 °C · p. 12
What it is and has
13- Device type
- Automotive fully integrated H-bridge motor driver · p. 1
- Qualification
- AEC-Q100 qualified · p. 1
- Environmental compliance
- ECOPACK, lead free and RoHS compliant · p. 1
- Output current
- 30 A · p. 1
- Logic inputs
- 3 V CMOS compatible · p. 1
- Protection
- Undervoltage and overvoltage shutdown · p. 1
- Protection
- High-side and low-side thermal shutdown · p. 1
- Protection
- Cross-conduction protection · p. 1
- Protection
- Current limitation · p. 1
- PWM operation
- Up to 20 kHz · p. 1
- Protection
- Loss of ground and loss of VCC · p. 1
- Current sense
- Output proportional to motor current · p. 1
- Charge pump
- Output for reverse polarity protection · p. 1
Around it
5- cap 500 μF per 10 A load current
- between supply line and GND; Blocking capacitor C; basic recommendation, size for application ripple and motor energy returned when the bridge enters 3-state. · p. 16
- other N-channel Power MOSFET, BVdss > 20 V
- between VBAT and VCC; Reverse battery protection for a reverse battery of -16 V; source to VBAT, drain to VCC, gate to CP; standard logic gate driving; RDS(on) less than one third of total H-bridge RDS(on). · p. 15
- res external pull-up resistor
- between ENA/DIAGA and pull-up supply; Required for half-bridge A enable and diagnostic status. · p. 6
- res external pull up resistor
- between ENB/DIAGB and pull-up supply; Required for half-bridge B enable and diagnostic status. · p. 7
- res series resistor
- between microcontroller I/O and driver I/O; Required to limit current sunk from microcontroller I/Os during reverse battery conditions; size using the stated I/O reverse current limit. · p. 19
Specifications
113| Parameter | Conditions | As printed | Page |
|---|---|---|---|
| Maximum battery voltage VBAT | With n-channel MOSFET used for reverse battery protection | min -16 V | 9 |
| Maximum battery voltage VBAT | With n-channel MOSFET used for reverse battery protection | max 41 V | 9 |
| Maximum bridge supply voltage VCC | max 41 V | 9 | |
| Maximum output current (continuous) Imax | max 30 A | 9 | |
| Reverse output current (continuous) IR | min -30 A | 9 | |
| Input current (INA and INB pins) IIN | min -10 · max 10 mA | 9 | |
| Enable input current (DIAGA/ENA and DIAGB/ENB pins) IEN | min -10 · max 10 mA | 9 | |
| PWM input current Ipw | min -10 · max 10 mA | 9 | |
| CP output current ICP | min -10 · max 10 mA | 9 | |
| CS_DIS input current ICS_DIS | min -10 · max 10 mA | 9 | |
| Electrostatic discharge (human body model: R = 1.5 k, C = 100 pF) VESD | max 2 kV | 10 | |
| Case operating temperature Tc | min -40 · max 150 °C | 10 | |
| Storage temperature TSTG | min -55 · max 150 °C | 10 | |
| Thermal resistance junction-case HSD Rthj-case | MultiPowerSO-30 | max 1.7 °C/W | 10 |
| Thermal resistance junction-case LSD Rthj-case | MultiPowerSO-30 | max 3.2 °C/W | 10 |
| Operating bridge supply voltage VCC | min 5.5 · max 24 V | 11 | |
| Supply current IS | OFF-state with all fault cleared and ENx = 0 V (standby); INA = INB = PWM = 0; Tj = 25 °C; VCC = 13 V | typ 10 · max 15 uA | 11 |
| Supply current IS | OFF-state with all fault cleared and ENx = 0 V (standby); INA = INB = PWM = 0 | max 60 uA | 11 |
| Supply current IS | OFF-state (no standby); INA = INB = PWM = 0; ENx = 5 V | max 6 mA | 11 |
| Supply current IS | ON-state; INA or INB = 5 V, no PWM | typ 4 · max 8 mA | 11 |
| Supply current IS | ON-state; INA or INB = 5 V, PWM = 20 kHz | max 8 mA | 11 |
| Static high-side resistance RONHS | IOUT = 15 A; Tj = 25 °C | typ 12 m | 11 |
| Static high-side resistance RONHS | IOUT = 15 A; Tj = - 40 °C to 150 °C | max 26.5 m | 11 |
| Static low-side resistance RONLS | IOUT = 15 A; Tj = 25 °C | typ 6 m | 11 |
| Static low-side resistance RONLS | IOUT = 15 A; Tj = - 40 °C to 150 °C | max 11.5 m | 11 |
| High-side free-wheeling diode forward voltage Vf | If = 15 A, Tj = 150 °C | typ 0.6 · max 0.8 V | 11 |
| High-side OFF-state output current (per channel) IL(off) | Tj = 25 °C; VOUTX = ENX = 0 V; VCC = 13 V | max 3 uA | 11 |
| High-side OFF-state output current (per channel) IL(off) | Tj = 125 °C; VOUTX = ENX = 0 V; VCC = 13 V | max 5 uA | 11 |
| Low-level input voltage VIL | Normal operation (DIAGX/ENX pin acts as an input pin) | max 0.9 V | 11 |
| High-level input voltage VIH | Normal operation (DIAGX/ENX pin acts as an input pin) | min 2.1 V | 11 |
| Low-level input current IINL | VIN = 0.9 V | min 1 uA | 11 |
| High-level input current IINH | VIN = 2.1 V | max 10 uA | 11 |
| Input hysteresis voltage VIHYST | Normal operation (DIAGX/ENX pin acts as an input pin) | min 0.15 V | 11 |
| Input clamp voltage VICL | IIN = 1 mA | min 5.5 · typ 6.3 · max 7.5 V | 12 |
| Input clamp voltage VICL | IIN = -1 mA | min -1 · typ -0.7 · max -0.3 V | 12 |
| Enable low-level output voltage VDIAG | Fault operation (DIAGX/ENX pin acts as an output pin); IEN = 1 mA | max 0.4 V | 12 |
| PWM frequency f | VCC = 13 V, RLOAD = 0.87 , Tj = 25 °C | min 0 · max 20 kHz | 12 |
| HSD rise time td(on) | Input rise time < 1us; see Figure 9; VCC = 13 V, RLOAD = 0.87 , Tj = 25 °C | max 250 us | 12 |
| HSD fall time td(off) | Input rise time < 1us; see Figure 9; VCC = 13 V, RLOAD = 0.87 , Tj = 25 °C | max 250 us | 12 |
| LSD rise time tr | See Figure 8; VCC = 13 V, RLOAD = 0.87 , Tj = 25 °C | typ 1 · max 2 us | 12 |
| LSD fall time tf | See Figure 8; VCC = 13 V, RLOAD = 0.87 , Tj = 25 °C | typ 1 · max 2 us | 12 |
| Delay time during change of operating mode tDEL | See Figure 7; VCC = 13 V, RLOAD = 0.87 , Tj = 25 °C | min 200 · typ 400 · max 1600 us | 12 |
| High-side free wheeling diode reverse recovery time trr | See Figure 10; VCC = 13 V, RLOAD = 0.87 , Tj = 25 °C | typ 110 ns | 12 |
| Dynamic cross-conduction current IRM | IOUT = 15 A; see Figure 10; VCC = 13 V, RLOAD = 0.87 , Tj = 25 °C | typ 2 A | 12 |
| VCC undervoltage shutdown VUSD | typ 4.5 · max 5.5 V | 12 | |
| VCC undervoltage shutdown hysteresis VUSDhyst | typ 0.5 V | 12 | |
| VCC overvoltage shutdown VOV | min 24 · typ 27 · max 30 V | 12 | |
| High-side current limitation ILIM_H | min 30 · typ 50 · max 70 A | 12 | |
| Low-side shutdown current ISD_LS | min 70 · typ 115 · max 160 A | 12 | |
| High-side clamp voltage (VCC to OUTA = 0 or OUTB = 0) VCLPHS | IOUT = 15 A | min 43 · typ 48 · max 54 V | 12 |
| Low-side clamp voltage (OUTA = VCC or OUTB = VCC to GND) VCLPLS | IOUT = 15 A | min 27 · typ 30 · max 33 V | 12 |
| Thermal shutdown temperature TTSD | VIN = 2.1 V; minimum threshold temperature between HS and LS | min 150 · typ 175 · max 200 °C | 12 |
| Low-side thermal shutdown temperature TTSD_LS | VIN = 0 V | min 150 · typ 175 · max 200 °C | 13 |
| Thermal reset temperature TTR | Valid for both HSD and LSD | min 135 °C | 13 |
| Thermal hysteresis THYST | Valid for both HSD and LSD | min 7 · typ 15 °C | 13 |
| IOUT/ISENSE K0 | IOUT = 3 A, VSENSE = 0.5 V, Tj = - 40 °C to 150°C | min 4670 · typ 7110 · max 10110 | 13 |
| Analog current sense ratio drift dK0/K0 | IOUT = 3 A; VSENSE = 0.5 V, Tj = -40 °C to 150 °C | min -19 · max 19 % | 13 |
| IOUT/ISENSE K1 | IOUT = 8 A, VSENSE = 1.3V, Tj = - 40 °C to 150°C | min 6060 · typ 7030 · max 8330 | 13 |
| Analog current sense ratio drift dK1/K1 | IOUT = 8 A; VSENSE = 1.3V, Tj = -40 °C to 150 °C | min -14 · max 14 % | 13 |
| IOUT/ISENSE K2 | IOUT = 15 A, VSENSE = 2.4 V, Tj = - 40 °C to 150°C | min 6070 · typ 6990 · max 7810 | 13 |
| Analog current sense ratio drift dK2/K2 | IOUT = 15 A; VSENSE = 2.4 V, Tj = -40 °C to 150 °C | min -12 · max 12 % | 13 |
| IOUT/ISENSE K3 | IOUT = 25 A, VSENSE = 4 V, Tj = - 40 °C to 150°C | min 6000 · typ 6940 · max 7650 | 13 |
| Analog current sense ratio drift dK3/K3 | IOUT =25 A; VSENSE = 4 V, Tj = -40 °C to 150 °C | min -12 · max 12 % | 13 |
| Max analog sense output voltage VSENSE | IOUT = 15 A, RSENSE = 1.1 k | min 5 V | 13 |
| Analog sense leakage current ISENSEO | IOUT = 0 A, VSENSE = 0 V, VCSD = 5 V, VIN = 0 V, Tj = - 40 to 150°C | min 0 · max 5 uA | 13 |
| Analog sense leakage current ISENSEO | IOUT = 0 A, VSENSE = 0 V, VCSD = 0 V, VIN = 5 V, Tj = - 40 to 150°C | min 0 · max 100 uA | 13 |
| Delay response time from falling edge of CS_DIS pin tDSENSEH | VIN = 5 V, VSENSE < 4 V, IOUT = 8 A, ISENSE = 90% of ISENSEmax; see Figure 13 | max 50 us | 13 |
| Delay response time from rising edge of CS_DIS pin tDSENSEL | VIN = 5 V, VSENSE < 4 V, IOUT = 8 A, ISENSE = 10% of ISENSEmax; see Figure 13 | max 20 us | 13 |
| R1 = R7 R1 = R7 | Area/island: Footprint | typ 0.1 °C/W | 29 |
| R2 = R8 R2 = R8 | Area/island: Footprint | typ 0.3 °C/W | 29 |
| R3 = R10 = R16 R3 = R10 = R16 | Area/island: Footprint | typ 0.5 °C/W | 29 |
| R4 R4 | Area/island: Footprint | typ 6 °C/W | 29 |
| R5 R5 | Area/island: Footprint | typ 30 °C/W | 29 |
| R5 R5 | Area/island: 4 cm2 | typ 24 °C/W | 29 |
| R5 R5 | Area/island: 8 cm2 | typ 24 °C/W | 29 |
| R5 R5 | Area/island: 16 cm2 | typ 24 °C/W | 29 |
| R6 R6 | Area/island: Footprint | typ 56 °C/W | 29 |
| R6 R6 | Area/island: 4 cm2 | typ 52 °C/W | 29 |
| R6 R6 | Area/island: 8 cm2 | typ 42 °C/W | 29 |
| R6 R6 | Area/island: 16 cm2 | typ 32 °C/W | 29 |
| R9 = R15 R9 = R15 | Area/island: Footprint | typ 0.05 °C/W | 29 |
| R11 = R17 R11 = R17 | Area/island: Footprint | typ 0.7 °C/W | 29 |
| R12 = R18 R12 = R18 | Area/island: Footprint | typ 10 °C/W | 29 |
| R13 = R19 R13 = R19 | Area/island: Footprint | typ 36 °C/W | 29 |
| R13 = R19 R13 = R19 | Area/island: 4 cm2 | typ 26 °C/W | 29 |
| R13 = R19 R13 = R19 | Area/island: 8 cm2 | typ 26 °C/W | 29 |
| R13 = R19 R13 = R19 | Area/island: 16 cm2 | typ 26 °C/W | 29 |
| R14 = R20 R14 = R20 | Area/island: Footprint | typ 56 °C/W | 29 |
| R14 = R20 R14 = R20 | Area/island: 4 cm2 | typ 42 °C/W | 29 |
| R14 = R20 R14 = R20 | Area/island: 8 cm2 | typ 36 °C/W | 29 |
| R14 = R20 R14 = R20 | Area/island: 16 cm2 | typ 28 °C/W | 29 |
| R21 = R22 R21 = R22 | Area/island: Footprint | typ 35 °C/W | 29 |
| R21 = R22 R21 = R22 | Area/island: 4 cm2 | typ 25 °C/W | 29 |
| R21 = R22 R21 = R22 | Area/island: 8 cm2 | typ 25 °C/W | 29 |
| R21 = R22 R21 = R22 | Area/island: 16 cm2 | typ 25 °C/W | 29 |
| R23 R23 | Area/island: Footprint | typ 160 °C/W | 29 |
| R23 R23 | Area/island: 4 cm2 | typ 150 °C/W | 29 |
| R23 R23 | Area/island: 8 cm2 | typ 150 °C/W | 29 |
| R23 R23 | Area/island: 16 cm2 | typ 150 °C/W | 29 |
| C1 = C7 = C9 = C15 C1 = C7 = C9 = C15 | Area/island: Footprint | typ 0.005 W.s/°C | 29 |
| C2 = C8 C2 = C8 | Area/island: Footprint | typ 0.01 W.s/°C | 29 |
| C3 C3 | Area/island: Footprint | typ 0.03 W.s/°C | 29 |
| C4 C4 | Area/island: Footprint | typ 0.4 W.s/°C | 29 |
| C5 C5 | Area/island: Footprint | typ 1.5 W.s/°C | 29 |
| C5 C5 | Area/island: 4 cm2 | typ 2 W.s/°C | 29 |
| C5 C5 | Area/island: 8 cm2 | typ 2 W.s/°C | 29 |
| C5 C5 | Area/island: 16 cm2 | typ 2 W.s/°C | 29 |
| C6 C6 | Area/island: Footprint | typ 3 W.s/°C | 29 |
| C6 C6 | Area/island: 4 cm2 | typ 4 W.s/°C | 29 |
| C6 C6 | Area/island: 8 cm2 | typ 5 W.s/°C | 29 |
| C6 C6 | Area/island: 16 cm2 | typ 6 W.s/°C | 29 |
| C10 = C16 C10 = C16 | Area/island: Footprint | typ 0.015 W.s/°C | 29 |
| C11 = C17 C11 = C17 | Area/island: Footprint | typ 0.05 W.s/°C | 29 |
Pins, by the datasheet
33- 1 OUTA
- High-side A source and low-side A drain; power connection to the motor. · p. 6
- 2 N.C.
- Not connected. · p. 6
- 3 VCC
- High-side switch drains; connect to the drain of the external reverse battery protection PowerMOS. · p. 6
- 4 INA
- Clockwise input; CMOS compatible. · p. 7
- 5 ENA/DIAGA
- Half-bridge A enable and fault status; requires an external pull-up resistor; pulling low disables half-bridge A. · p. 6
- 6 CS_DIS
- Active high CMOS compatible input that disables current sense. · p. 7
- 7 PWM
- PWM input; CMOS compatible. · p. 7
- 8 CS
- Current output proportional to motor current when CS_DIS is low or open; use an external resistor to read an analog voltage. · p. 7
- 9 ENB/DIAGB
- Half-bridge B enable and fault status; requires an external pull-up resistor; pulling low disables half-bridge B. · p. 7
- 10 INB
- Counter clockwise input; CMOS compatible. · p. 7
- 11 CP
- Connect to the gate of the external reverse battery protection MOS. · p. 7
- 12 VBAT
- Battery connection; connect to the source of the external reverse battery protection PowerMOS. · p. 6
- 13 VCC
- High-side switch drains; connect to the drain of the external reverse battery protection PowerMOS. · p. 6
- 14 N.C.
- Not connected. · p. 6
- 15 OUTB
- High-side B source and low-side B drain; power connection to the motor. · p. 7
- 16 OUTB
- High-side B source and low-side B drain; power connection to the motor. · p. 7
- 17 N.C.
- Not connected. · p. 6
- 18 GNDB
- Low-side B source and power ground; externally connect GNDA and GNDB together. · p. 7
- 19 GNDB
- Low-side B source and power ground; externally connect GNDA and GNDB together. · p. 7
- 20 GNDB
- Low-side B source and power ground; externally connect GNDA and GNDB together. · p. 7
- 21 OUTB
- High-side B source and low-side B drain; power connection to the motor. · p. 7
- 22 N.C.
- Not connected. · p. 6
- 23 VCC
- High-side switch drains; connect to the drain of the external reverse battery protection PowerMOS. · p. 6
- 24 N.C.
- Not connected. · p. 6
- 25 OUTA
- High-side A source and low-side A drain; power connection to the motor. · p. 6
- 26 GNDA
- Low-side A source and power ground; externally connect GNDA and GNDB together. · p. 7
- 27 GNDA
- Low-side A source and power ground; externally connect GNDA and GNDB together. · p. 7
- 28 GNDA
- Low-side A source and power ground; externally connect GNDA and GNDB together. · p. 7
- 29 N.C.
- Not connected. · p. 6
- 30 OUTA
- High-side A source and low-side A drain; power connection to the motor. · p. 6
- Heat Slug1 VCC
- High-side switch drains and connection to the drain of the external reverse battery protection PowerMOS. · p. 6
- Heat Slug2 OUTA
- High-side A source and low-side A drain; power connection to the motor. · p. 6
- Heat Slug3 OUTB
- High-side B source and low-side B drain; power connection to the motor. · p. 7
Ordering codes, by the datasheet
1- VNH5019ATR-E
- MultiPowerSO-30 · Tape and reel · p. 35
- 4 layers81.3 × 52.8 mm

- 4 layers60 × 60 mm

B VNH5019ATR W ENC ELITE BRK R1.0
Boardoza/Boardoza_VNH5019ATR_w-Enc_Elite_Breakout_Board
High-power H-bridge motor driver breakout board based on STMicroelectronics VNH5019A-E with integrated encoder interface and thermal heatsink design.
32 parts1CC-BY-SA-4.0 - 4 layers140 × 100 mm

Recline actuator controller
Accessibilita/recline-controls
Hardware project for open source wheel chair recline control electronics
181 partsCERN-OHL-S-2.0 - 4 layers80 × 40 mm

B VNH5019-BRK R1.0
Boardoza/Boardoza_VNH5019_H_Bridge_Motor_Driver_Module
B-VNH5019-BRK is a high-current full H-bridge motor driver module based on the VNH5019A-E for 5.5V–24V DC motor control.
22 partsCC-BY-SA-4.0 - 2 layers150 × 180 mm

- 4 layers55 × 100 mm

- 2 layers150 × 160.8 mm

ProcessingUnit
senrobo/open
. │ ├── l1 │ ├── 3dmodels │ │ ├── .DSStore │ │ ├── 0603Inductor.step │ │ ├── 1040Inductor.step │ │ ├── ALS-PT19.step │ │ ├── C0603.step │ │ ├── CAPPRD750W80D1600H2500.stp │ │ ├── CD74HC4067M.step │ │…
136 partsMIT - 4 layers70 × 157.5 mm

Controller Tv Lift
vyrubaev/TV-Lift-Controller
TVLift Controller is an intelligent controller for TV lift and lower mechanisms, based on the ESP32 microcontroller.
103 parts
Parts like it
2Questions
Is there a KiCad symbol and footprint for the VNH5019ATR-E?
Yes. The symbol is EasyEDA_Cloud:VNH5019ATR-E and the footprint EasyEDA_Cloud:MULTIPOWERSO-30_L17.2-W16.0-P1.00-LS19.0-BL, both drawn on this page. PCBKit places them on a board for you when you design with it.
What package is the VNH5019ATR-E?
MultiPowerSO-30, with 33 pins. Its footprint is drawn on this page.
Where is the VNH5019ATR-E datasheet?
STMicroelectronics publishes it: the Datasheet link on this page opens it.
Where can I order the VNH5019ATR-E?
JLCPCB lists it as part C2653552, with 834 in stock; the sellers' links on this page open their listings.
What can replace the VNH5019ATR-E?
Parts like it in the library: the VNH3SP30TR-E by STMicroelectronics and the VNH3SP30-E by STMicroelectronics. Check their datasheets: a part that fits the footprint may still differ in its ratings.
Which open-source boards use the VNH5019ATR-E?
9 boards in 8 repositories on GitHub; the most starred are listed on this page, with their KiCad files.