

Shop guard
I built this pcb using esp32, and lidar sensor to monitor and alert shop owner of intruders
- Copper layers
- 2
- Thickness
- 1.6 mm
- Parts
- 29
- Nets
- 57
- Pads
- 184
- Tracks, vias
- 343, 52
- Routed
- Yes
- KiCad
- KiCad 8.0 (file 20240108)
- Created
- 13 Apr 2025
- Updated
- 8 Jul 2025
Overview
Shop guard is an open-source printed circuit board by Aust1nke, from the Aust1nke/Security_shop_guard repository on GitHub. It is a 2-layer board with 29 parts on 57 nets, routed with 343 tracks and 52 vias.
It is built around the ESP32-C3-WROOM-02-H4, LM2576HVS-3.3 and PAM8302AADCR, with the TP4057 among its other parts. Its parts include 7 capacitors, 6 resistors, 6 ICs, 6 diodes and 1 connector. It belongs with the ESP32 and RISC-V boards of this library.
Main components
4ESP32-C3-WROOM-02-H4
SMD,20x18mm-105dBm -40℃~+105℃ 2.4GHz 20.5dBm 345mA 3V~3.6V 82mA Bluetooth5.0 ESP32-C3 On-board PCB Antenna UART、SPI、I2C、I2S、USB SMD,20x18mm WiFi Modules ROHSEspressif SystemsWiFi ModulesLM2576HVS-3.3
TO-263-5-40℃~+125℃@(TJ) 1 10mA 3.3V 3A 4V~60V 52kHz Buck Buck Built-in Fixed No TO-263-5 DC-DC Converters ROHSTexas InstrumentsDC-DC ConvertersPAM8302AADCR
SOP-8-40℃~+85℃ 0.3% 1-Channel 2.5Wx1@4Ω 2V~5.5V 4mA 50dB 80dB 85% Class D Filterless architecture SOP-8 Audio Amplifiers ROHSDiodes IncorporatedAudio AmplifiersTP4057
SOT-23-6-40℃~+85℃ 1 25uA 4.24V 4V~6.5V Charging IC Lithium Battery Not supported SOT-23-6 Battery Management ROHSTECH PUBLICBattery Management
Parts
29| Qty | Value | Footprint | References |
|---|---|---|---|
| 5 | 1000uF | Capacitor_SMD:C_0201_0603Metric | C1, C2, C3, C4, C5 |
| 4 | D | Diode_SMD:D_0201_0603Metric | D2, D3, D4, D5 |
| 3 | 10k | Resistor_SMD:R_0201_0603Metric | R2, R3, R4 |
| 2 | 1k | Resistor_SMD:R_0201_0603Metric | R6, R7 |
| 2 | LM2576HVS-3.3 | Package_TO_SOT_SMD:TO-263-5_TabPin3 | U3, U5 |
| 1 | 100nF | Capacitor_SMD:C_0201_0603Metric | C6 |
| 1 | 100uF | Capacitor_SMD:C_0201_0603Metric | C7 |
| 1 | 5.1k | Resistor_SMD:R_0201_0603Metric | R5 |
| 1 | Battery | Battery:BatteryHolder_Keystone_2466_1xAAA | BT1 |
| 1 | ESP32-C3-WROOM-02 | RF_Module:ESP32-C3-WROOM-02 | U1 |
| 1 | L | Inductor_SMD:L_Neosid_SM-PIC0512H | L1 |
| 1 | LED 1 | LED_THT:LED_D3.0mm_Horizontal_O6.35mm_Z10.0mm | D1 |
| 1 | LED 2 | LED_THT:LED_D3.0mm_Horizontal_O6.35mm_Z10.0mm | D6 |
| 1 | PAM8302AAD | Package_TO_SOT_SMD:SOT-23-6 | U6 |
| 1 | Speaker | Buzzer_Beeper:Speaker_CUI_CMR-1206S-67 | LS1 |
| 1 | TP4057 | Package_TO_SOT_SMD:TSOT-23-5 | U4 |
| 1 | USB_C_Receptacle_USB2.0_14P | Connector_USB:USB_C_Receptacle_GCT_USB4105-xx-A_16P_TopMnt_Horizontal | J1 |
| 1 | VL53L0CXV0DH1 | Sensor_Distance:ST_VL53L1x | U2 |
Similar boards
- 2 layers76 × 22 mm

- 2 layers18 × 14.4 mm

- 2 layers29.8 × 49.8 mm

- 4 layers51 × 33 mm

- 2 layers45 × 42.5 mm

Whaap
bardiasayyar/Custom-PCB-Wearable-Step-Fall-Tracker
Designing a custom wristband PCB in KiCad integrating an ESP32-C3 microcontroller, LSM6DS3 IMU (I2C), and LiPo battery/charging circuitry for real-time step counting, fall detection, and battery monitoring.
31 parts - 2 layers24 × 40 mm

Gps
louis-bourgault/gps
This project is, first and foremost, a custom devboard made for macondo. It has a esp32-c3 chip on it. A main tenant of its design is to be as power efficient as possible, because of its secondary purpose as a GNSS…
26 parts - 2 layers74 × 83.8 mm

PCB Board
RunningJoke/reactionButton
ReactPod: ESP32-C3 reaction buzzers – firmware, Config App (PWA), tools, hardware
70 parts - 4 layers181.7 × 80 mm

Questions
What parts does the Shop guard use?
29 parts, built around the ESP32-C3-WROOM-02-H4, LM2576HVS-3.3, PAM8302AADCR and TP4057. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the Shop guard KiCad files?
From the Aust1nke/Security_shop_guard repository on GitHub, at the commit this page was made from: the board is shop guard.kicad_pcb and its schematic shop guard.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Can I use the Shop guard design in my own project?
Its repository states no licence, so its author keeps all rights: ask Aust1nke before reusing the design.