Skip to the content
2 layers45 × 42.5 mmWhaap, the printed circuit board in 3D

Designing a custom wristband PCB in KiCad integrating an ESP32-C3 microcontroller, LSM6DS3 IMU (I2C), and LiPo battery/charging circuitry for real-time step counting, fall detection, and battery monitoring.

Size
45 × 42.5 mm
Copper layers
2
Thickness
1.6 mm
Parts
31
Nets
29
Pads
131
Tracks, vias
41, 4
Routed
Yes
KiCad
KiCad 10.0 (file 20260206)
Created
1 Sep 2026
Updated
9 Sep 2026

Overview

Whaap is an open-source printed circuit board by bardiasayyar, from the bardiasayyar/Custom-PCB-Wearable-Step-Fall-Tracker repository on GitHub. It is a 2-layer board of 45 × 42.5 mm with 31 parts on 29 nets, routed with 41 tracks and 4 vias.

It is built around the ESP32-C3-WROOM-02-H4, LSM6DS3 and TP4057. Its parts include 11 resistors, 10 capacitors, 4 ICs, 2 connectors and 1 diode. It belongs with the power boards and the ESP32 and RISC-V boards of this library.

Main components

3

README

README.md

Custom PCB Wearable Step & Fall Tracker

A wristband device built from a custom PCB (designed in KiCad) that performs step counting, fall/impact detection, and battery monitoring, with a browser-based dashboard for live data — no native app required.

This is a personal project built to demonstrate end-to-end hardware, firmware, and software integration: schematic design, PCB layout, embedded firmware, and BLE communication.

Features

  • Step counting — derived from accelerometer motion data
  • Fall/impact detection — threshold-based detection using IMU acceleration spikes
  • Battery monitoring — live battery percentage
  • Web Bluetooth dashboard — real-time data in-browser (Chrome/Edge) via BLE, no companion app

Deliberately excluded: GPS (unreliable indoors, poor for live demos) and heart rate (adds complexity without adding to the core demo).

Hardware

ComponentPartNotes
MCUESP32-C3-WROOM-02Analog inputs restricted to ADC1 (GPIO0–4); GPIO2 avoided (bootstrapping pin)
AccelerometerLSM6DS3I2C mode, address 0x6A (SDO/SA0 → GND), 4.7 kΩ pull-ups on SDA/SCL
BatteryAdafruit #42363.7 V, 420 mAh LiPo, JST-PH, built-in protection
Charger ICTP4057PROG = 3.9 kΩ (~250 mA charge rate), 1 µF VCC bypass
Voltage RegulatorMCP1700-3302ELDO; steps VBAT (3.0–4.2 V) down to a clean 3.3 V logic rail
USB-CUSB_C_Receptacle_PowerOnly_6PSingle 5.1 kΩ pull-down on CC (CC1/CC2 bridged on this part)

Key design decision: the battery/charger line is never wired directly to the 3.3 V rail — VBAT can hit 4.2 V, above the ESP32's rated supply. The MCP1700 LDO sits between VBAT and 3V3 to protect the MCU.

Software

  • Firmware: C/C++ (ESP32 Arduino framework)
  • Dashboard: HTML/JS using the Web Bluetooth API (BLE GATT), Chrome/Edge only

Repository Structure

text
├── hardware/         # KiCad project files (.kicad_pro, .kicad_sch, .kicad_pcb)
├── firmware/          # ESP32 firmware source
├── dashboard/         # Web Bluetooth dashboard (HTML/JS)
├── docs/              # Exported schematic PDF/PNG, notes
└── README.md

Project Status

  • Lock in hardware decisions (MCU, IMU, power architecture, USB-C)
  • Finish schematic in KiCad
  • Run ERC, resolve all warnings
  • Assign footprints
  • Order parts + PCB
  • Breadboard prototype — validate step/fall detection firmware before committing to custom board
  • Finish PCB layout
  • Solder + bring-up in stages (power → MCU → sensor)
  • Port firmware to custom PCB
  • BLE + dashboard integration
  • Enclosure/strap
  • Demo polish

Currently in finalizing PCB design.

Why This Project

Built to show practical hardware + firmware + software skills in a single, demoable device. Alined with my areas of interest and real world use.

whaap-1 tracker-flowchart

Parts

31
QtyValueFootprintReferences
41uFCapacitor_SMD:C_0603_1608MetricC4, C5, C6, C9
30.1uFCapacitor_SMD:C_0603_1608MetricC1, C2, C3
310kResistor_SMD:R_0603_1608MetricR9, R10, R11
2100kResistor_SMD:R_0603_1608MetricR1, R2
2100nFCapacitor_SMD:C_0603_1608MetricC7, C8
24.7kResistor_SMD:R_0603_1608MetricR3, R4
25.1kResistor_SMD:R_0603_1608MetricR5, R6
2SW_PushButton_Switch_SMD:SW_SPST_TL3342BUTB1, BUTR1
110uFCapacitor_SMD:C_0603_1608MetricC10
11kResistor_SMD:R_0603_1608MetricR8
13.3Connector_JST:JST_PH_S2B-PH-K_1x02_P2.00mm_HorizontalB1
13.9KResistor_SMD:R_0603_1608MetricR7
1Conn_01x04_PinConnector_PinHeader_2.54mm:PinHeader_1x04_P2.54mm_VerticalJ1
1ESP32-C3-WROOM-02RF_Module:ESP32-C3-WROOM-02U1
1LEDLED_SMD:LED_0603_1608MetricD1
1LSM6DS3Package_LGA:LGA-14_3x2.5mm_P0.5mm_LayoutBorder3x4yU3
1MCP1700x-330xxTTPackage_TO_SOT_SMD:SOT-23U4
1TP4057Package_TO_SOT_SMD:TSOT-23-6U2
1USB_CConnector_USB:USB_C_Receptacle_GCT_USB4125-xx-x_6P_TopMnt_HorizontalJ2

Similar boards

  • 2 layers85 × 85 mmCube display, the printed circuit board in 3D

    Cube display

    atomic14/cube-display

    I'm currently testing the first set of PCBs. There will be updates as I find issues!

    73 parts2
  • 2 layers18 × 14.4 mmBauble pcb, the printed circuit board in 3D

    Bauble pcb

    Spritetm/esp32c3-doom-bauble

    Christmas tree bauble with an ESP32C3 running Doom

    19 parts89
  • 2 layers29.8 × 49.8 mmGummySlime, the printed circuit board in 3D

    GummySlime

    gumorr/GummySlime

    Cheesecake compatible SlimeVR pcbs

    28 parts1
  • 4 layers51 × 33 mmSmolExG, the printed circuit board in 3D

    SmolExG

    matthewlai/SmolExG

    63 parts1
  • 2 layersShop guard, the printed circuit board in 3D

    Shop guard

    Aust1nke/Security_shop_guard

    I built this pcb using esp32, and lidar sensor to monitor and alert shop owner of intruders

    29 parts
  • 2 layers24 × 40 mmGps, the printed circuit board in 3D

    Gps

    louis-bourgault/gps

    This project is, first and foremost, a custom devboard made for macondo. It has a esp32-c3 chip on it. A main tenant of its design is to be as power efficient as possible, because of its secondary purpose as a GNSS…

    26 parts
  • 2 layers74 × 83.8 mmPCB Board, the printed circuit board in 3D

    PCB Board

    RunningJoke/reactionButton

    ReactPod: ESP32-C3 reaction buzzers – firmware, Config App (PWA), tools, hardware

    70 parts
  • 4 layers25.6 × 23.6 mmCANNONBALL, the printed circuit board in 3D

    CANNONBALL

    user-will/PCB_CANNONBALL

    An ESP32-C3 dev board with more sensors and features then you could know what to do with

    61 parts14

Questions

How big is the Whaap PCB?

It measures 45 × 42.5 mm and has 2 copper layers, 1.6 mm thick.

What parts does the Whaap use?

31 parts, built around the ESP32-C3-WROOM-02-H4, LSM6DS3 and TP4057. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the Whaap KiCad files?

From the bardiasayyar/Custom-PCB-Wearable-Step-Fall-Tracker repository on GitHub, at the commit this page was made from: the board is whaap.kicad_pcb and its schematic whaap.kicad_sch. PCBKit opens the board in the browser, with nothing to install.

Can I use the Whaap design in my own project?

Its repository states no licence, so its author keeps all rights: ask bardiasayyar before reusing the design.