2 layers129.9 × 63.6 mm
Traeger rev 2.3.0.kicad pro
jazzmonger/Traeger-PID-Controller
Traeger Smoker/Grill Controller based on an
45 parts36
2 layers48 × 47 mm
ReflowOvenPCB
7FM/ReflowOvenControl1with the focus of using the UI schemes of the first two projects and using the profile management & control algorithms from Controleo3.
- Size
- 48 × 47 mm
- Copper layers
- 2
- Thickness
- 1.6 mm
- Parts
- 26
- Nets
- 30
- Pads
- 97
- Tracks, vias
- 96, 0
- Pours
- 11
- Routed
- Yes
- KiCad
- KiCad 5 (file 20171130)
- Created
- 7 Nov 2020
- Updated
- 16 Oct 2026
Overview
ReflowOvenPCB is an open-source printed circuit board by 7FM, from the 7FM/ReflowOvenControl repository on GitHub, published under the GPL-3.0 licence. It is a 2-layer board of 48 × 47 mm with 26 parts on 30 nets, routed with 96 tracks and 0 vias.
It is built around the MAX6675ISA+. Its parts include 9 connectors, 3 resistors, 3 ICs, 1 capacitor and 1 transistor.
Main components
1README
README.mdReflowOvenControl
This repo is a combination of the following great projects:
- https://github.com/dasaki/nanoReflowController
- https://github.com/0xPIT/reflowOvenController
- https://github.com/engineertype/Controleo3.git
with the focus of using the UI schemes of the first two projects and using the profile management & control algorithms from Controleo3.
The whole project targets an Arduino Nano and therefore almost all used Libraries where optimized for space and sometimes for performance too.
Profiles
As mentiened before this projects uses the Controleo Profile Management but with a reduced Token set (see: src/read_profiles.cpp or include/read_profiles.hpp). A good overview for all tokens(also non supported ones) with explanation can be found here.
Hardware
- Arduino Nano
- 1.8'' Color TFT display (ST7735R) as from Adafruit: https://www.adafruit.com/product/358 (can be replaced with serial UI only)
- Rotary Encoder (can be replaced with serial UI only)
- SD Card reader
- Thermocouple reader (MAX6675)
- Buzzer (optional)
- Servo (optional)
- SSR or something to control the oven
- oven to be controlled
- cooling fan (optional)
- convection fan (optional)
For convenience a custom PCB was created using KiCad but is not mandatory. Please note that I am no professional (resistors & transistor were arbitrarily chosen by own availability) so any use of the PCB at your own risk! I also designed some 3D Models using FreeCAD for mounting the hardware.
Building
Clone the repository with git clone --recursive as submodules are used.
If already cloned, the submodules can also be downloaded afterwards using: git submodule update --init --recursive.
For compiling simply use PlatformIO.
Configuration
Features, Pins & more can be configured in src/config.h. Feel free to ask if the impact of certain options is unclear.
Useful ressources
Parts
26| Qty | Value | Footprint | References |
|---|---|---|---|
| 3 | 220 | Resistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P7.62mm_Horizontal | R1, R2, R3 |
| 2 | Jumper_3_Open | Connector_PinHeader_2.54mm:PinHeader_1x03_P2.54mm_Vertical | JP1, JP2 |
| 1 | Analog | Socket_Arduino_Nano:Socket_Strip_Arduino_1x15 | P2 |
| 1 | Analog Pins | Connector_PinHeader_2.54mm:PinHeader_1x02_P2.54mm_Vertical | J3 |
| 1 | Barrel_Jack_MountingPin | Connector_BarrelJack:BarrelJack_Horizontal | J1 |
| 1 | Buzzer | Buzzer_Beeper:Buzzer_12x9.5RM7.6 | LS1 |
| 1 | CP | Capacitor_THT:CP_Radial_D8.0mm_P3.50mm | C1 |
| 1 | Digital | Socket_Arduino_Nano:Socket_Strip_Arduino_1x15 | P1 |
| 1 | Free Pins | Connector_PinHeader_2.54mm:PinHeader_1x02_P2.54mm_Vertical | J4 |
| 1 | GND Outs | Connector_PinSocket_2.54mm:PinSocket_1x04_P2.54mm_Vertical | J5 |
| 1 | KY-040 | Connector_PinHeader_2.54mm:PinHeader_1x05_P2.54mm_Vertical | S1 |
| 1 | MAX6675 | Connector_PinHeader_2.54mm:PinHeader_1x05_P2.54mm_Vertical | U3 |
| 1 | MicroSDReader | Connector_PinHeader_2.54mm:PinHeader_1x06_P2.54mm_Vertical | U1 |
| 1 | Motor_Servo | Connector_PinHeader_2.54mm:PinHeader_1x03_P2.54mm_Vertical | M1 |
| 1 | Q_PNP_CBE | Package_TO_SOT_THT:TO-92_Inline_Wide | Q1 |
| 1 | SSR | Connector_PinHeader_2.54mm:PinHeader_1x02_P2.54mm_Vertical | U2 |
| 1 | Serial Pins | Connector_PinHeader_2.54mm:PinHeader_1x02_P2.54mm_Vertical | J2 |
| 1 | TFT | Connector_PinHeader_2.54mm:PinHeader_1x07_P2.54mm_Vertical | DS1 |
| 1 | VCC Out1 | Connector_PinSocket_2.54mm:PinSocket_1x02_P2.54mm_Vertical | J6 |
| 1 | VCC Out2 | Connector_PinSocket_2.54mm:PinSocket_1x02_P2.54mm_Vertical | J7 |
The 23 most common of 26 parts.
Questions
How big is the ReflowOvenPCB PCB?
It measures 48 × 47 mm and has 2 copper layers, 1.6 mm thick.
What parts does the ReflowOvenPCB use?
26 parts, built around the MAX6675ISA+. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the ReflowOvenPCB KiCad files?
From the 7FM/ReflowOvenControl repository on GitHub, at the commit this page was made from: the board is hardware/reflowOvenPCB/reflowOvenPCB.kicad_pcb. PCBKit opens the board in the browser, with nothing to install.
Can I use the ReflowOvenPCB design in my own project?
Its repository publishes it under the GPL-3.0 licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).
Similar boards
- 2 layers176 × 82.6 mm
- 2 layers73.7 × 61 mm
- 2 layers60 × 75 mm
- 2 layers77.5 × 42.3 mm
- 2 layers70 × 100 mm
BREAD Slice
FHafting/BREAD
This project is fully documented in the paper: Shane Oberloier, Nicholas G. Whisman, Finn Hafting, Joshua M. Pearce, Open Source Framework for a Broadly Expandable and Reconfigurable Data Acquisition and Automation…
48 parts5 - 2 layers
- 2 layers71.1 × 35.1 mm
Brilliant Reflow v0.1
LKbrilliant/Brilliant-Reflow
A complete DIY solution for converting a consumer oven into a temperature controlled reflow oven for PCB soldering
28 parts4MIT