

DroneV1
- Size
- 167.8 × 167.8 mm
- Copper layers
- 2
- Thickness
- 1.6 mm
- Parts
- 54
- Nets
- 40
- Pads
- 216
- Tracks, vias
- 0, 0
- Routed
- Not yet
- KiCad
- KiCad 5 (file 20171130)
- Created
- 22 Dec 2019
- Updated
- 24 Dec 2019
Overview
DroneV1 is an open-source printed circuit board by 15jgme, from the 15jgme/Drone-project repository on GitHub. It is a 2-layer board of 167.8 × 167.8 mm with 54 parts on 40 nets.
It is built around the ESP8266EX, BMP280 and W25Q32JVSSIQ, with the RT9193-33GB and MPU-6050 among its other parts. Its parts include 20 resistors, 15 capacitors, 8 ICs, 4 diodes and 1 connector. It belongs with the ESP8266 boards of this library.
Main components
5ESP8266EX
QFN-32-EP(5x5)-40℃~+125℃ -91dBm 120mA 2.4GHz 2.4GHz~2.4835GHz 2.5V~3.6V 21.5dBm 50mA 72.2Mbps SPI、UART、I2C、I2S WiFi transceiver QFN-32-EP(5x5) RF Transceiver ICs ROHSEspressif SystemsRF Transceiver ICsBMP280
LGA-8(2x2.5)-40℃~+85℃ 0.12hpa 1.5pa/K 1.71V~3.6V 1hpa 300nA 30Kpa~1.1bar I2C、SPI Integrated ADC and digital interface、On-chip calibration and non-volatile storage、Standby mode、On-chip temperature output LGA-8(2x2.5) Pressure Sensors ROHSBoschPressure SensorsW25Q32JVSSIQ
SOIC-8-208mil-40℃~+85℃ 100,000 cycles 133MHz 1uA 2.7V~3.6V 20 Years 32Mbit 3ms SPI SOIC-8-208mil NOR FLASH ROHSWinbondNOR FLASHRT9193-33GB
SOT-23-5-40℃~+125℃@(Tj) -50dB@(10kHz) 1 100uVrms 220mV@(300mA) 3.3V 300mA 5.5V 90uA Fixed Over Current Protection、Over Temperature Protection、Enable Positive SOT-23-5 Voltage Regulators - Linear, Low Drop Out (LDO) Regulators ROHSRICHTEKVoltage Regulators - Linear, Low Drop Out (LDO) RegulatorsMPU-6050
QFN-24-EP(4x4)-40℃~+85℃ 16bit 1KB 2.375V~3.46V 5uA Accelerometer Gyroscope I2C X,Y,Z X,Y,Z ±16g ±2000dps QFN-24-EP(4x4) Accelerometers ROHSTDK InvenSenseAccelerometers
README
README.mdDrone project
Parts
54| Qty | Value | Footprint | References |
|---|---|---|---|
| 8 | 1k | Resistor_SMD:R_0603_1608Metric | R1, R2, R3, R4, R5, R6, R7, R8 |
| 4 | 100nF | Capacitor_SMD:C_0603_1608Metric | C10, C11, C13, C14 |
| 4 | 1uF | Capacitor_SMD:C_0603_1608Metric | C4, C5, C8, C9 |
| 4 | LED | LED_SMD:LED_0201_0603Metric | D1, D2, D3, D4 |
| 4 | Motor_DC | Connector_PinHeader_2.54mm:PinHeader_1x02_P2.54mm_Vertical | M1, M2, M3, M4 |
| 3 | 10k | Resistor_SMD:R_0603_1608Metric | R11, R15, R17 |
| 3 | C | Capacitor_SMD:C_0603_1608Metric | C1, C2, C3 |
| 2 | 1R | Resistor_SMD:R_0603_1608Metric | R9, R10 |
| 2 | 22nF | Capacitor_SMD:C_0603_1608Metric | C6, C7 |
| 2 | 47R | Resistor_SMD:R_0603_1608Metric | R16, R18 |
| 2 | 75R | Resistor_SMD:R_0402_1005Metric | R12, R14 |
| 2 | RT9193-33GB | RT9193-33GB:SOT94P279X130-5N | IC2, IC3 |
| 1 | 10k | Resistor_SMD:R_0201_0603Metric | R13 |
| 1 | 10nF | Capacitor_SMD:C_0603_1608Metric | C12 |
| 1 | 2.2nF | Capacitor_SMD:C_0603_1608Metric | C15 |
| 1 | 200R | Resistor_SMD:R_0603_1608Metric | R19 |
| 1 | 4.7k | Resistor_SMD:R_0603_1608Metric | R20 |
| 1 | 74HC14D,652 | Package_DIP:DIP-14_W7.62mm | IC1 |
| 1 | BMP280 | Package_LGA:Bosch_LGA-8_2x2.5mm_P0.65mm_ClockwisePinNumbering | U3 |
| 1 | Conn_01x02_Male | Connector_JST:JST_PH_S2B-PH-K_1x02_P2.00mm_Horizontal | J1 |
| 1 | Crystal_GND24 | Crystal:Crystal_SMD_3225-4Pin_3.2x2.5mm | Y1 |
| 1 | DroneOutline | DroneV1:DroneOutlineOLD | U5 |
| 1 | ESP8266EX | Package_DFN_QFN:QFN-32-1EP_5x5mm_P0.5mm_EP3.45x3.45mm | U1 |
| 1 | MPU-6050 | Sensor_Motion:InvenSense_QFN-24_4x4mm_P0.5mm | U4 |
| 1 | R_Pack04 | Package_DIP:DIP-8-16_W7.62mm | RN1 |
| 1 | W25Q32JVSS | Package_SO:SOIC-8_5.23x5.23mm_P1.27mm | U2 |
Similar boards
- 4 layers52 × 25 mm

- 4 layers38 × 38 mm

- 2 layers161.3 × 76.1 mm

Stm32 timer app
ymhtwe/stm32_timer_app
general purpose control applications using stm32 timer module
117 parts - 2 layers37.8 × 21.5 mm

- 6 layers158 × 158 mm

Fpv drone
zeodotdev/zeo-boards
ESP32-S3 development board with onboard BME280 (temperature, humidity, pressure) and LSM6DS3 (6-axis IMU) sensors. This repo contains the designs, ESP-IDF firmware, and a Python plotter for visualization.
158 parts3 - 2 layers40 × 10 mm

- 2 layers

- 2 layers57.2 × 57.2 mm

Questions
How big is the DroneV1 PCB?
It measures 167.8 × 167.8 mm and has 2 copper layers, 1.6 mm thick.
What parts does the DroneV1 use?
54 parts, built around the ESP8266EX, BMP280, W25Q32JVSSIQ and RT9193-33GB. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the DroneV1 KiCad files?
From the 15jgme/Drone-project repository on GitHub, at the commit this page was made from: the board is DroneV1/DroneV1.kicad_pcb. PCBKit opens the board in the browser, with nothing to install.
Can I use the DroneV1 design in my own project?
Its repository states no licence, so its author keeps all rights: ask 15jgme before reusing the design.