2 layers178.2 × 110.9 mm
LegRobotBoardTeensy
01binary/str1ker
A human-scale mech integrated with Robot Operating System
179 parts20
2 layers87.5 × 55 mm
ArmRobotBoardTeensy
01binary/str1ker20A human-scale mech integrated with Robot Operating System
- Size
- 87.5 × 55 mm
- Copper layers
- 2
- Thickness
- 1.6 mm
- Parts
- 53
- Nets
- 87
- Pads
- 201
- Tracks, vias
- 573, 59
- Pours
- 2
- Routed
- Yes
- KiCad
- KiCad 9.0 (file 20241229)
- Created
- 15 Feb 2020
- Updated
- 18 Aug 2026
Overview
ArmRobotBoardTeensy is an open-source printed circuit board by 01binary, from the 01binary/str1ker repository on GitHub. It is a 2-layer board of 87.5 × 55 mm with 53 parts on 87 nets, routed with 573 tracks and 59 vias.
It is built around the SN74HC08DR(LX), B4B-XH-A and B3B-XH-A, with the B2B-XH-A, B5B-XH-AM and SMMBT3904LT1G-HXY among its other parts. Its parts include 20 resistors, 11 diodes, 11 connectors, 4 ICs and 2 capacitors. It belongs with the NXP (LPC, Kinetis, i.MX RT) boards of this library.
Main components
6
SN74HC08DR(LX)
SOP-14Logic Gateslingxingic
B4B-XH-A
插件,P=2.5mm,4PUncategorisedJST
B3B-XH-A
UncategorisedJST Automotive Connectors
B2B-XH-A
插件,P=2.5mm-25℃~+85℃ 1 1x2P 2 2.5mm 250V 2P 3A 5.75mm 7.4mm 7mm Brass K Pin PA66 Through Hole Tin UL94V-0 White XH 插件,P=2.5mm Wire To Board Connector ROHSJSTWire To Board Connector
B5B-XH-AM
插件,P=2.5mm-25℃~+85℃ 1 14.9mm 1x5P 2.5mm 250V 3A 5 5.75mm 5P 7mm Brass K Pin、With post PA66 Through Hole Tin UL94V-0 White XH 插件,P=2.5mm Wire To Board Connector ROHSJSTWire To Board Connector
SMMBT3904LT1G-HXY
SOT-23Bipolar (BJT)HXY MOSFET
README
boards/LegRobotBoardTeensy/readme.mdLeg Robot Board
A board that controls the mobile platform with four mecanum wheels:
- Leg Actuators
- Leg Actuator Potentiometers
- Leg Wheels
- Leg Wheel Encoders
- 9-DOF IMU
- Enabled and PWM activity LEDs
- Wheel Speed 7-Segment LED Indicators
Modules
The following components are placed onto the board as modules:
| Module | Function |
|---|---|
| Teensy 4.1 | ROS Node |
| Adafruit 9-DOF IMU | TF2 Transform |
Devices
The following external components are connected to the board via JST-XH locking connectors:
| Device | Function |
|---|---|
| 8x IBT2 Motor Drivers | Wheel Motor Drivers, Leg Actuator Drivers (8 pin IDC connector: 3V3, GND, L_EN, R_EN, LPWM, RPWM, L_IS, R_IS) |
| 4x Feedback Rod Linear Actuator Potentiometers | Leg Actuator Potentiometers (3 pin JST-XH connector: 3V3, SIG, GND) |
| 4x Leg (Wheel) Encoder Board | Wheel Encoders (8 pin IDC connector: A, B, I, 3V3, and four GND's |
Functionality
PWM
There are four legs and each has two motors: a linear lift actuator and a brushed DC motor that runs the wheel.
Each PWM channel gets its own EN (Enabled) signal. The current sense signals (L_IS, R_IS) are included in the connector layout and sent over the wire, but not used anywhere on the board because there aren't enough pins for them. A multiplexer can be added later if the signals are desired.
ADC
The linear lift actuators have built-in multi-turn potentiometers. These are routed to Teensy ADC pins.
Quadrature
The wheel encoders are connected to each of the four wheels, outputting A, B, and I pulses counting rotations (1000 pulses per revolution).
Number Displays
Four 7-segment common anode LED number displays with decimal points display the speed of each wheel from 0.0 to 1.0. They are driven by an LED multiplexer.
The LED multiplexer is mapped to four 2-digit LED displays with decimal point as follows:
| Display function | IS31FL3730 pins |
|---|---|
| Digit common anodes | SW1–SW8 |
| Segments A, B, C, D, E, F, G, DP | CS1–CS8 |
The 3621BH common-anode LED displays have the following pin footprint:
| 1 | 2 | 3 | 4 | 5 | |
|---|---|---|---|---|---|
| 1 | COM0 | B | C | E | D |
| 2 | G | DP | A | F | COM1 |
The digit segments are mapped as follows:
| Digit | Segments |
|---|---|
 | A - Top of upper squareF - Left of upper squareB - Right of upper squareG - Link of both squaresE - Left of lower squareC - Right of lower squareD - Bottom of lower squareDP - Decimal point |
Pin Mapping
This board is essentially a shield. Labeled locking connectors are provided for all of the devices, PWM enabled/activity is indicated by LEDs, and wheel speeds are indicated by number displays.
| Pin | Function | Group |
|---|---|---|
A16 | Actuator 1 Potentiometer SIG | Front Left Leg (Actuator) |
D32 | Quadrature Encoder 1 A | Front Left Leg (Wheel) |
D33 | Quadrature Encoder 1 B | Front Left Leg (Wheel) |
D22 | Quadrature Encoder 1 Index | Front Left Leg (Wheel) |
D26 | Motor Driver 1 EN | Front Left Leg (Wheel) |
D27 | Motor Driver 2 EN | Front Left Leg (Actuator) |
D0 | Motor Driver 1 RPWM | Front Left Leg (Wheel) |
D1 | Motor Driver 1 LPWM | Front Left Leg (Wheel) |
D2 | Motor Driver 2 RPWM | Front Left Leg (Actuator) |
D3 | Motor Driver 2 LPWM | Front Left Leg (Actuator) |
A17 | Actuator 2 Potentiometer SIG | Front Right Leg (Actuator) |
D34 | Quadrature Encoder 2 A | Front Right Leg (Wheel) |
D35 | Quadrature Encoder 2 B | Front Right Leg (Wheel) |
D23 | Quadrature Encoder 2 Index | Front Right Leg (Wheel) |
D28 | Motor Driver 3 EN | Front Right Leg (Wheel) |
D29 | Motor Driver 4 EN | Front Right Leg (Actuator) |
D4 | Motor Driver 3 RPWM | Front Right Leg (Wheel) |
D5 | Motor Driver 3 LPWM | Front Right Leg (Wheel) |
D6 | Motor Driver 4 RPWM | Front Right Leg (Actuator) |
D7 | Motor Driver 4 LPWM | Front Right Leg (Actuator) |
A2 | Actuator 3 Potentiometer SIG | Rear Left Leg (Actuator) |
D36 | Quadrature Encoder 3 A | Rear Left Leg (Wheel) |
D37 | Quadrature Encoder 3 B | Rear Left Leg (Wheel) |
D24 | Quadrature Encoder 3 Index | Rear Left Leg (Wheel) |
D30 | Motor Driver 5 EN | Rear Left Leg (Wheel) |
D31 | Motor Driver 6 EN | Rear Left Leg (Actuator) |
D8 | Motor Driver 5 RPWM | Rear Left Leg (Wheel) |
D9 | Motor Driver 5 LPWM | Rear Left Leg (Wheel) |
D10 | Motor Driver 6 RPWM | Rear Left Leg (Actuator) |
D11 | Motor Driver 6 LPWM | Rear Left Leg (Actuator) |
A3 | Actuator 4 Potentiometer SIG | Rear Right Leg (Actuator) |
D38 | Quadrature Encoder 4 A | Rear Right Leg (Wheel) |
D39 | Quadrature Encoder 4 B | Rear Right Leg (Wheel) |
D25 | Quadrature Encoder 4 Index | Rear Right Leg (Wheel) |
D20 | Motor Driver 7 EN | Rear Right Leg (Wheel) |
D21 | Motor Driver 8 EN | Rear Right Leg (Actuator) |
D12 | Motor Driver 7 RPWM | Rear Right Leg (Wheel) |
D13 | Motor Driver 7 LPWM | Rear Right Leg (Wheel) |
D14 | Motor Driver 8 RPWM | Rear Right Leg (Actuator) |
D15 | Motor Driver 8 LPWM | Rear Right Leg (Actuator) |
A5 | I2C SCL | IMU, LED Driver |
A4 | I2C SDA | IMU, LED Driver |
Buses
| Device | Bus | Address |
|---|---|---|
| IMU | I2C | 0x28 (ADR tied to GND to set address) |
| IS31FL3730 | I2C | 0x74 |
Bill of Materials
| Component | Description |
|---|---|
| IS31FL3730 | LED Driver/Multiplexer |
| CL3621BH | LED Displays (2-Digit, 7-Segment, 10-Pin Common Anode) for Wheel Speeds |
| XL-1608SURC-06 | Red LED for EN signals |
| 150080BS75000 | Blue LED for LPWM/RPWM signals |
| RC0603FR-07150RL | 150 Ohm LED Resistor |
| RC0603FR-07470RL | 470R Red LED Resistor |
| RCG06031K00FKEA | 1K LED Resistor |
| RC0603FR-072K2L | 2.2K Series Resistor (ADC channels) |
| CR0603-FX-4701ELF | 4.7K Pull-Up Resistor for LED Multiplexer |
| CRCW060310K0FKEA | 10K 555 Timer Pull-Up Resistor, Transistor Base Resistor |
| HoAR0603-1/10W-20KR-1%-TCR25 | 20K LED Driver Current Setting Resistor |
| CRCW0603100KFKEA | 100K Transistor Base Pull-Down Resistor |
| RC0603FR-07360KL | 360K 555 Timer Resistor |
| C0402C103J4RACTU | 10nF 555 Timer Capacitor |
| CL10B473KB8NNNC | 47nF Decoupling Capacitor (ADC channels) |
| CC0603KRX7R9BB104 | 100nF IMU Capacitor |
| CC0603JRX7R7BB105 | 1uF 555 Timer Capacitor |
| SN74HC08DR | IC Gate |
| MMBT3904LT1G | LED Transistor |
| TLC555CDR | 555 Timer |
| JST_XH_B3B-XH-A | Actuator Potentiometers (3V3, SIG, GND) |
| Molex 0702460802 | Motor Drivers (LPWM, RPWM, L_EN, R_EN, L_IS, R_IS, 3V3, GND) |
| Teensy 4.1 | Teensy 4.1 without Headers |
| ICM-648-1-GT-HT | Teensy IC DIP Socket, 48P |
| Needle Headers | Teensy Needle Headers for DIP Socket |
| DIP Socket 10 pin | LED number displays IC socket |
Parts
53| Qty | Value | Footprint | References |
|---|---|---|---|
| 7 | 150R | RCG06031K00FKEA:RCG06031K00FKEA | R1, R2, R3, R4, R6, R7, R11 |
| 7 | BLUE LED | 150080BS75000:150080BS75000_Modified | D1, D2, D3, D4, D6, D7, D9 |
| 5 | B4B-XH-A | Connector_JST:JST_XH_B4B-XH-A_1x04_P2.50mm_Vertical | J2, J5, J8, J9, J10 |
| 4 | 1K | RCG06031K00FKEA:RCG06031K00FKEA | R5, R10, R12, R13 |
| 4 | MountingHole_Pad | MountingHole:MountingHole_3.2mm_M3_ISO7380_Pad | MH1, MH2, MH3, MH4 |
| 4 | RED LED | NCD0603R1:NCD0603R1 | D5, D8, D10, D11 |
| 3 | 100K | CRCW0603100KFKEA:CRCW0603100KFKEA | R9, R14, R17 |
| 3 | 5.1K | RC0603FR-075K1L:RC0603FR-075K1L | R18, R19, R20 |
| 3 | B3B-XH-A | Connector_JST:JST_XH_B3B-XH-A_1x03_P2.50mm_Vertical | J3, J4, J11 |
| 2 | 10K | CRCW060310K0FKEA:CRCW060310K0FKEA | R8, R15 |
| 2 | B2B-XH-A | Connector_JST:JST_XH_B2B-XH-A_1x02_P2.50mm_Vertical | J6, J7 |
| 2 | SN74HC08DR | SN74HC08DR:SN74HC08DR | U3, U4 |
| 1 | 0.01uF | C0402C103J4RACTU:C0402C103J4RACTU | C2 |
| 1 | 1uF | CC0603JRX7R7BB105:CC0603JRX7R7BB105 | C1 |
| 1 | 360K | RC0603FR-07360KL:RC0603FR-07360KL | R16 |
| 1 | B5B-XH-A | Connector_JST:JST_XH_B5B-XH-A_1x05_P2.50mm_Vertical | J1 |
| 1 | SMMBT3904LT1G | SMMBT3904LT1G:SMMBT3904LT1G | Q1 |
| 1 | TLC555CDR | TLC555CDR:TLC555CDR | U2 |
| 1 | Teensy4.0 | Teensy:Teensy40_SMT | U1 |
Questions
How big is the ArmRobotBoardTeensy PCB?
It measures 87.5 × 55 mm and has 2 copper layers, 1.6 mm thick.
What parts does the ArmRobotBoardTeensy use?
53 parts, built around the SN74HC08DR(LX), B4B-XH-A, B3B-XH-A and B2B-XH-A. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the ArmRobotBoardTeensy KiCad files?
From the 01binary/str1ker repository on GitHub, at the commit this page was made from: the board is boards/ArmRobotBoardTeensy/ArmRobotBoardTeensy.kicad_pcb and its schematic boards/ArmEncoderBoard/ArmEncoderBoard.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Can I use the ArmRobotBoardTeensy design in my own project?
Its repository states no licence, so its author keeps all rights: ask 01binary before reusing the design.
More from 01binary/str1ker
6- 2 layers174 × 121.1 mm
MainRobotBoardTeensy
01binary/str1ker
A human-scale mech integrated with Robot Operating System
163 parts20 - 2 layers44.1 × 18.4 mm
- 2 layers34 × 34 mm
- 2 layers58.4 × 46.5 mm
- 2 layers54.5 × 33 mm
Similar boards
- 2 layers100 × 100 mm
Motherboard
Luca-Jones/enph-253-pet-rescue
The mechanical design was done with Onshape as our CAD tool. It is simple to use and allows for collaboration and version control.
31 parts - 2 layers85.5 × 92.4 mm
Actuator board
nawalhussein/Actuation-Node-PCB-for-Autonomous-Car-using-KiCad
This project contains the complete hardware design (schematics and PCB layout) and associated software for a custom-built STM32-based actuator control system to be put in the autonomous car.
36 parts - 4 layers50 × 80 mm
ARGOS DEMO
CNES/argos-demo-board
Demo board designed to use the ARRIBADA SMD module via USB to send ARGOS messages to the Kineis constellation.
91 parts7CERN-OHL-S-2.0 - 4 layers113.4 × 56 mm
- 2 layers116.9 × 75.6 mm
- 4 layers62.2 × 75.6 mm
ElectronicsPCBv1
CUSail-Navigation/PCB-FA25-SP26
This is a repository containing the PCBs designed during the FA25-SP26 academic year. Due to high compatibility and relative ease of use, all of these files are made with KiCad.
17 parts - 2 layers
- 2 layers49.8 × 80.8 mm
FDRPCB
Samalmeida1028/sdp-team-12
This is the repository for Team 12's Senior Design Project (SDP)
42 parts1