

Motherboard 4layer
Open source 3D printer
- Size
- 113.4 × 56 mm
- Copper layers
- 4
- Thickness
- 1.6 mm
- Parts
- 57
- Nets
- 160
- Pads
- 371
- Tracks, vias
- 1,041, 125
- Routed
- Yes
- KiCad
- KiCad 8.0 (file 20240108)
- Created
- 4 Sep 2024
- Updated
- 16 Oct 2026
Overview
Motherboard 4layer is an open-source printed circuit board by hackclub, from the hackclub/forge-printer repository on GitHub, published under the GPL-3.0 licence. It is a 4-layer board of 113.4 × 56 mm with 57 parts on 160 nets, routed with 1,041 tracks and 125 vias.
It is built around the TMC2209SILENTSTEPSTICK, LM2576HVS-5 and AMS1117-3.3, with the B2B-XH-A, B4B-XH-A and EEEFT1V101AP among its other parts. Its parts include 10 capacitors, 8 resistors, 7 ICs, 3 diodes and 2 transistors. It belongs with the robots and motor control and computers and single-board computers boards and the STM32 boards of this library.
Main components
12TMC2209SILENTSTEPSTICK
-Power Management - Modules ROHSTRINAMIC Motion Control GmbHModulesLM2576HVS-5
TO-263-5-40℃~+125℃ 1 4V~60V 52kHz Buck Buck TO-263-5 DC-DC Converters ROHSTexas InstrumentsDC-DC ConvertersAMS1117-3.3
SOT-223-40℃~+125℃ 0.003%Vout 1 1.1V@(800mA) 15V 1A 3.3V 5mA 72dB@(120Hz) Fixed Over Current Protection、Short Circuit Protection、Thermal shutdown Positive SOT-223 Voltage Regulators - Linear, Low Drop Out (LDO) Regulators ROHSAdvanced Monolithic SystemsVoltage Regulators - Linear, Low Drop Out (LDO) RegulatorsB2B-XH-A
插件,P=2.5mm-25℃~+85℃ 1 1x2P 2 2.5mm 250V 2P 3A 5.75mm 7.4mm 7mm Brass K Pin PA66 Through Hole Tin UL94V-0 White XH 插件,P=2.5mm Wire To Board Connector ROHSJSTWire To Board ConnectorB4B-XH-A
插件,P=2.5mm,4PUncategorisedJSTEEEFT1V101AP
SMD,D6.3xL5.8mm-55℃~+105℃ 100uF 2000hrs@105℃ 260mΩ@100kHz 300mA@100kHz 35V 6.1mm 6.3mm Polarized ±20% SMD,D6.3xL5.8mm Aluminum Electrolytic Capacitors - SMD ROHSPanasonicAluminum Electrolytic Capacitors - SMDAO3400A
SOT-23-55℃~+150℃ 1 N-channel 1.45V 1.4W 30V 48mΩ@2.5V 5.7A 50pF 630pF 75pF 7nC@10V N-Channel SOT-23 MOSFETs ROHSAlpha & Omega SemiconductorMOSFETsWS2812
SMD5050-4P1.57mm 1000mcd 110mcd 120us 2kHz 3.7V~5.3V 300ns 320mcd 451nm 523nm 5mm 5mm 623nm 800Kbit/s Built-in power-on reset circuit、Built-in power-on reset circuit Top-mount SMD5050-4P RGB LEDs(Built-in IC) ROHSWorldsemiRGB LEDs(Built-In IC)RMCF0805JT5K10
0805-55℃~+155℃ 125mW 150V 5.1kΩ Thick Film Resistor ±200ppm/℃ ±5% 0805 Chip Resistor - Surface Mount ROHSStackpole Electronics (SEI)Chip Resistor - Surface MountB3B-XH-A
UncategorisedJST Automotive ConnectorsDX07S024JJ3R1300
SMD-30℃~+80℃ 1 24P 250mA、1.25A 48V Black Female Surface Mount, Right Angle Type-C USB 3.2 SMD USB Connectors ROHSJAE ElectronicsUSB ConnectorsEEEFN1C221XP
SMD,D6.3xL7.7mm-55℃~+105℃ 16V 2000hrs@105℃ 220uF 280mA@100kHz 340mΩ@100kHz Polarized ±20% SMD,D6.3xL7.7mm Aluminum Electrolytic Capacitors - SMD ROHSPanasonicAluminum Electrolytic Capacitors - SMD
README
README.mdWIP Disclaimers
- This is an potential upcoming Hack Club You Ship, We Ship (YSWS) program.
This project is semi-endorsed by Hack Club and isn't fully an official program yet.
- Things are still under heavy development as the Forge Printer are WIP (Work in Progress) projects
- All information on this README is subject to change at any moment
- Submission requirements, images, and links are not final. Website URLs are placeholders and may not be functional
- If you have any questions about the Development of Forge (and are a teen under 18), feel free to visit #forge-dev on the Hack Club Slack!
Forge, Hack Club's 3D Printer
2nd Place Finalist of the Hack Club Arcade Showcase 2024, out of over 2000 projects.
Find problems in the world and use programmatic 3D modeling to solve them. Submit your solutions to the Gallery and get a Forge 3D Printer Forge is planned to be a You Ship, We Ship project from Hack Club.
Forge is fully open source. We encourage all to submit to the gallery through PRs! However, you must be a teenager or younger to receive a free printer.
About the Forge Printer
The Forge Printer is a fast, inexpensive, and compact cantilevered 3D Printer. More details soon!
Specifications
These are Forge's specifications as of June 10, 2025. We're currently still in the process of building MK2. More details will be published soon.
- STM32F405RGT6 32-Bit MCU
- TMC2209 Stepper Drivers
- Reduced Motor Noise
- Sensorless XY homing
- TZ-E3 Hotend
- 300°C Maximum Temperature
- Designed around the Bambu Lab X1C hotend
- 30mm³/s max flow rate
- 120x120x140mm Build Volume
- Up to 100°C heated bed temperature
- Magnetic Textured PEI Plate
- MGN9C Linear Rails
- ProtoXtruder Direct Drive Extruder (DDE)
- Fully Automatic Bed Leveling using BLTouch (ABL)
- Meanwell RPS-200-24 PSU (Integrated) with a protected C14 Inlet (used on the majority of consumer 3D printers)
- PLA, PETG, TPU capable
- ABS and ASA are possible but require an enclosure and active ventilation
- Aluminum and 3D Printed ASA frame
- DragonBurner Toolhead
- Up to 500mm/s Print Velocity* *This number is an estimate, real print speeds will be updated as Forge's development continues
Firmware
-
The Forge Mainboard will run on Marlin Firmware. (Custom, open source Forge Firmware had been planned but development has been halted as as of right now it is unrealistic)
-
The Forge Mainboard is supported by Klipper
- Using the Forge Printer with Klipper will be possible! The latest revision of the Forge Mainboard (2 layer PCB version) runs a STM32F405 which is fully compatible with Klipper! Additionally, we'll be providing a Klipper WiP configuration file and OrcaSlicer profiles (Coming Soon) for you!
- SBC Info:
- A Raspberry Pi Zero 2W will be required for Klipper. You can also use another SBC (that can run MainSailOS or Fluidd) with the same form factor. However, the Zero W (1st Gen) is highly not recommended due to performance limitations. Larger SBCs like the Raspberry Pi 1/2/3/4/5 boards are not compatible due to size limitations. We'll be providing a Raspberry Pi Zero Bracket available to print closer to MK2's launch! The Forge Mainboard connects to the SBC via GPIO to GPIO, therefore, SPI touchscreens are not recommended.
Additional notes
- The full Forge Printer and Mainboard BOM will soon be at the bottom of this doc. The Forge Printer BOM will not be available until we begin prototyping. However, the BOM for the Forge Mainboard is currently available as a CSV in
Electronics/Motherboard/billofmaterials.csv. - The estimated value of the Forge Printer is $200-$300, but this estimate will change over time (Additionally, tariffs may impact this cost in the future).
- However, our goal is to offer Forge for free for teens 18 and under (details on how will come out soon) **
- Currently, Forge's parts and components are planned to be manufactured by Siboor, a well-established supplier of 3D Printing components.
- Forge is designed in Onshape. Check out the 3D model!
Licensing
- Currently, the Forge Project is GPLV3 (General Public License)
- Anybody is allowed to freely use, advertise, modify, copy, or distribute any Forge designs or software as needed, with the condition that any public distribution or use of Forge software/design must also be open source and use GPL.
- For more information about this license, check out this link
Support the Project!
- Forge's banking is fully transparent: Check it out now!
- Donate to the Forge Project, any dollar counts!
- **Forge is now offically fiscally sponsored by Hack Club (a 501(c)(3) NPO with EIN 81-2908499)!
Forge Project Credits:
Forge Team:
- Krishna Meda (@EmperorNumerius) - Project Lead, Communications, Promotional Materials
- Arnnav Kudale (@blazecoding2009) - Project Lead, Sourcing, Electrical Engineering, Forge Firmware/Klipper Config Dev
- Evan Le (@lolwutboi987) - Design Engineering
- Michael Panait (@mikeymascatu) - Design Engineering, Promotional Materials
- Malav Patel (@astro-develops) - Design Engineer, Forge Landing Page Frontend Developer, Promotional Materials
Note that we all kind of work on everything, listed above is just what we generally do
Special Thanks:
- Viv (@VivIsBee) - Forge Firmware Dev and PCB designer (MK1-MK2)
- Brendan Conover (@AGB556) - Former Design Engineer (MK2)
- Aaron Wong (@aaronw-dev) - Former Project Lead, Firmware Dev, Artist, Electrical Engineer (MK1)
- Engineering and Sales teams at Siboor
- Polymaker for sponsoring $100 of filament!
- Patricio (@Patcybermind) - Former Forge Editor Developer
- Max Wofford (@maxwofford) - Hack Club HQ Representative, Forge Benefactor
- Alex Ren (@qcoral) - Thanks for the help with licensing!
- Jonathan Dong (@Dongathan-Jong) - Forge Art, Promotional Materials
- Beenana (@Beenana02) - Promotional Materials
- And the community for supporting this project!!
Credits!
Parts
57| Qty | Value | Footprint | References |
|---|---|---|---|
| 8 | B2B-XH-A | B2B-XH-A:JST_B2B-XH-A | ABL1, FAN1, FAN2, FAN3, THM1, THM2, THM3, Z_END1 |
| 5 | RC1206JR-134K7L | RC1206JR-134K7L:RESC3216X65 | R1, R2, R3, R4, R6 |
| 4 | B4B-XH-A | B4B-XH-A:JST_B4B-XH-A | MOTOR_E1, MOTOR_X1, MOTOR_Y1, MOTOR_Z1 |
| 4 | EEEFT1V101AP | EEEFT1V101AP:CAP_EEEFT1V101AP | C1, C2, C3, C4 |
| 4 | TMC2209_SILENTSTEPSTICK | TMC2209_SILENTSTEPSTICK:MODULE_TMC2209_SILENTSTEPSTICK | U2, U3, U4, U5 |
| 3 | AO3400A | AO3400A:SOT95P280X125-3N | M1, M2, M3 |
| 3 | GCM155R71H104KE02J | GCM155R71H104KE02J:CAPC1005X55N | C5, C6, C7 |
| 3 | WS2812 | LED_SMD:LED_WS2812_PLCC6_5.0x5.0mm_P1.6mm | D1, D2, D3 |
| 2 | 1751248 | Phoenix 1751248:PHOENIX_1751248 | BED1, HOTEND1 |
| 2 | LOGO | LOGO | G***, G*** |
| 2 | RMCF0805JT5K10 | RMCF0805JT5K10:RESC2012X65N | R8, R9 |
| 2 | ~ | IRFH7440TRPBF:TRANS_FDMS86202 | Q1, Q2 |
| 1 | AMS1117-3.3 | Package_TO_SOT_SMD:SOT-223-3_TabPin2 | U1 |
| 1 | B3B-XH-A | b3b-xh-a:JST_B3B-XH-A | RGB1 |
| 1 | Conn_01x04_Pin | PinHeader:PinHeader_1x04_P2.54mm_Vertical | DEBUG1 |
| 1 | Conn_02x10_Odd_Even | 2x10_tht:PinBox-2.54-02x10-THT | J2 |
| 1 | DX07S024JJ3R1300 | DX07S024JJ3R1300:JAE_DX07S024JJ3R1300 | J1 |
| 1 | EEEFN1C221XP | EEEFN1C221XP:CAP_EEEFN1C221XP | C10 |
| 1 | LM2576HVS-5 | Package_TO_SOT_SMD:TO-263-5_TabPin3 | U6 |
| 1 | PEC11H-4015F-S0016 | PinHeader:PinHeader_1x04_P2.54mm_Vertical | REN1 |
| 1 | PJ-102B | PJ-102B:CUI_PJ-102B | PWR1 |
| 1 | RC0603FR-131KL | RC0603FR-131KL:0603 | R7 |
| 1 | RUEF900 | RUEF900:FUSRR1015W81L2410T300H2900 | F1 |
| 1 | SSD1306 | PinHeader:PinHeader_1x04_P2.54mm_Vertical | SCRN1 |
| 1 | STM32G0B1VETx | Package_QFP:LQFP-100_14x14mm_P0.5mm | U7 |
| 1 | UWT1V101MCL1GS | UWT1V101MCL1GS:CAPAE830X1000N | C8 |
| 1 | UWT1V331MNL1GS | UWT1V101MCL1GS:CAPAE830X1000N | C9 |
More from hackclub/forge-printer
3- 2 layers113.4 × 55.3 mm

- 2 layers113.4 × 56 mm

- 2 layers65 × 29 mm

Similar boards
- 4 layers166.6 × 77.8 mm

- 4 layers16.6 × 16.6 mm

Foc pcb
avaninder/GimbalFOC
A pcb that integrates an ESP32S3 with a DRV8313 for BLDC FOC control in a 3-axis camera gimbal
35 parts5 - 2 layers260.4 × 118.7 mm

- 4 layers114.3 × 108 mm

Pellet
Mouse-GYM/auto-trainer-hardware
Repository for hardware, firmware, and software related to the Mouse-GYM modules
202 parts - 6 layers18.3 × 36.1 mm

- 4 layers40 × 35 mm

SensWear V1R1-Debug
HeyPCB/senswear-kicad
Sens Wear's SensWear smart ring hardware, converted from their Altium design to KiCad 10. Design by Sens Wear (github.com/Sens-Wear/hardware), MIT.
25 partsMIT - 2 layers76.2 × 25.4 mm

- 4 layers65 × 71.8 mm

Questions
How big is the Motherboard 4layer PCB?
It measures 113.4 × 56 mm and has 4 copper layers, 1.6 mm thick.
What parts does the Motherboard 4layer use?
57 parts, built around the TMC2209SILENTSTEPSTICK, LM2576HVS-5, AMS1117-3.3 and B2B-XH-A. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the Motherboard 4layer KiCad files?
From the hackclub/forge-printer repository on GitHub, at the commit this page was made from: the board is Electronics/Motherboard/OldVersions/4l1/motherboard_4layer.kicad_pcb and its schematic Electronics/Motherboard/CurrentVersion/motherboard_2layers_v2.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Can I use the Motherboard 4layer design in my own project?
Its repository publishes it under the GPL-3.0 licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).