
TPS62A01ADRL
Texas InstrumentsExtended
-40℃~+125℃@(TJ) 1 1A 2.4MHz 2.5V~5.5V 20uA 600mV~5.5V Adjustable Buck Built-in Overcurrent Protection、Light load efficient mode、Output discharge、Operating status indication、Hiccup current limiting Step-down type Yes SOT-563 DC-DC Converters ROHS
- Part id
- ti/TPS62A01ADRL
- Category
- DC DC Converters
- Package
- SOT-563
- Pins
- 6
- In stock
- 6,571 at JLCPCB (C5181455)
- Used on
- 6 open-source boards
Overview
The TPS62A01ADRL is a DC DC Converter made by Texas Instruments in a SOT-563 package with 6 pins. -40℃~+125℃@(TJ) 1 1A 2.4MHz 2.5V~5.5V 20uA 600mV~5.5V Adjustable Buck Built-in Overcurrent Protection、Light load efficient mode、Output discharge、Operating status indication、Hiccup current limiting Step-down type Yes SOT-563 DC-DC Converters ROHS.
PCBKit's library has its KiCad symbol (Regulator_Switching:TPS62A01ADRL, from KiCad's library) and its footprint (Package_TO_SOT_SMD:SOT-563, from KiCad's library), ready for a KiCad board. 6,571 are in stock at JLCPCB (part C5181455). 6 open-source boards in 4 repositories on GitHub use it.
Symbol
Footprint
From the datasheet
11- Supply, least
- 2.5 V · VIN, recommended operating min · p. 4
- Supply, most
- 5.5 V · VIN, recommended operating max · p. 4
- Supply, absolute maximum
- 6 V · VIN, absolute maximum · p. 4
- Junction, hottest
- 150 °C · Operating junction temperature, absolute max · p. 4
- Takes asleep
- 10 nA · VIN shutdown supply current, typical, VEN low · p. 5
- Gives
- 1 A · TPS62A01A rated output current, max · p. 3
- Feedback reference
- 600 mV · FB voltage, typical, PWM mode · p. 5
- Switches at
- 2.4 MHz · FPWM switching frequency, typical, VIN = 5 V, VOUT = 1.8 V · p. 5
- Junction to air (DRL)
- 157.3 K/W · Junction-to-ambient thermal resistance · p. 5
- Junction to case (DRL)
- 92.2 K/W · Junction-to-case (top) thermal resistance · p. 5
- Junction to board (DRL)
- 45.6 K/W · Junction-to-board thermal resistance · p. 5
What it is and has
9- Operation mode
- FPWM · p. 3
- Adjustable output voltage
- 0.6 V to VIN · p. 1
- Feedback accuracy
- 1% (0°C to 125°C) · p. 1
- Duty cycle
- 100% mode operation · p. 1
- Protection
- Short circuit protection (HICCUP) · p. 1
- Protection
- Thermal shutdown · p. 1
- Soft start
- Internal · p. 1
- Output discharge
- Active · p. 1
- Package
- 6-pin DRL SOT-563 · p. 3
Around it
5- cap 4.7 µF
- between VIN and GND; Example C1: ceramic, 10 V, X7R, size 0805. · p. 11
- cap 22 µF
- between VOUT and GND; Example C2: ceramic, 10 V, X7R, size 0805. · p. 11
- ind 1 µH
- between SW and VOUT; Example L1; DFE252012F-1R0M for the 1-A design. · p. 11
- res ≤ 100 kΩ
- between FB and GND; R2 feedback divider resistor; upper bound for acceptable noise sensitivity. · p. 11
- cap 120 pF
- between VOUT and FB; Optional feedforward capacitor C3 for the 1.8-V example. · p. 11
Specifications
47| Parameter | Conditions | As printed | Page |
|---|---|---|---|
| Pin voltage | VIN, EN, PG | min -0.3 · max 6 V | 4 |
| Pin voltage | SW, DC | min -0.3 V | 4 |
| Pin voltage | SW, transient < 10 ns | min -3 · max 10 V | 4 |
| Pin voltage | FB | min -0.3 · max 3 V | 4 |
| Operating junction temperature TJ | min -40 · max 150 °C | 4 | |
| Storage temperature Tstg | min -55 · max 150 °C | 4 | |
| Electrostatic discharge V(ESD) | Human-body model (HBM), per ANSI/ESDA/JEDEC JS-001 | min -2000 · max 2000 V | 4 |
| Electrostatic discharge V(ESD) | Charged-device model (CDM), per JEDEC specification JESD22-C101 | min -500 · max 500 V | 4 |
| Input supply voltage range VIN | min 2.5 · max 5.5 V | 4 | |
| Output voltage range VOUT | min 0.6 V | 4 | |
| Output current range IOUT | TPS62A01 | min 0 · max 1 A | 4 |
| Effective inductance L | typ 1 uH | 4 | |
| Output capacitance COUT | VOUT < 1.2 V | typ 44 uF | 4 |
| Output capacitance COUT | 1.2 V ≤ VOUT < 1.8 V | typ 22 uF | 4 |
| Output capacitance COUT | VOUT ≥ 1.8 V | typ 10 uF | 4 |
| Power Good input current capability IPG | min 0 · max 1 mA | 4 | |
| Operating junction temperature TJ | min -40 · max 125 °C | 4 | |
| Junction-to-ambient thermal resistance RθJA | DRL, 6 pins | typ 157.3 °C/W | 5 |
| Junction-to-case (top) thermal resistance RθJC(top) | DRL, 6 pins | typ 92.2 °C/W | 5 |
| Junction-to-board thermal resistance RθJB | DRL, 6 pins | typ 45.6 °C/W | 5 |
| Junction-to-top characterization parameter ψJT | DRL, 6 pins | typ 4 °C/W | 5 |
| Junction-to-board characterization parameter ψJB | DRL, 6 pins | typ 45 °C/W | 5 |
| VIN quiescent current IQ(VIN) | TPS62A01; Non-switching, VEN = High, VFB = 610 mV | typ 20 uA | 5 |
| VIN shutdown supply current ISD(VIN) | VEN = Low | typ 0.01 · max 2 uA | 5 |
| VIN UVLO rising threshold VUVLO(R) | VIN rising | min 2.3 · typ 2.4 · max 2.5 V | 5 |
| VIN UVLO falling threshold VUVLO(F) | VIN falling | min 2.2 · typ 2.3 · max 2.4 V | 5 |
| EN voltage rising threshold VEN(R) | EN rising, enable switching | min 1.2 V | 5 |
| EN voltage falling threshold VEN(F) | EN falling, disable switching | max 0.4 V | 5 |
| EN Input leakage current VEN(LKG) | VEN = 5 V | max 100 nA | 5 |
| FB voltage VFB | TJ = 0°C to 125°C, PWM mode | min 594 · typ 600 · max 606 mV | 5 |
| FB voltage VFB | PWM mode | min 591 · typ 600 · max 609 mV | 5 |
| FB input leakage current IFB(LKG) | VFB = 0.6 V | max 100 nA | 5 |
| Switching frequency, FPWM operation fSW(FCCM) | VIN = 5 V, VOUT = 1.8 V | typ 2400 kHz | 5 |
| Internal fixed soft-start time | From EN = High to VFB = 0.56 V | max 1 ms | 5 |
| High-side MOSFET on-resistance RDSON(HS) | TPS62A01, VIN = 5V | typ 180 mΩ | 5 |
| Low-side MOSFET on-resistance RDSON(LS) | TPS62A01, VIN = 5V | typ 120 mΩ | 5 |
| High-side peak current limit IHS(OC) | TPS62A01 | min 1.3 · typ 1.8 A | 5 |
| Low-side valley current limit ILS(OC) | TPS62A01 | typ 1.8 A | 5 |
| Power-good threshold VPGTH | PG low, FB falling | typ 93.5 % | 5 |
| Power-good threshold VPGTH | PG high, FB rising | typ 96 % | 5 |
| PG delay falling | typ 35 us | 5 | |
| PG delay rising | typ 10 us | 5 | |
| PG pin Leakage current when open drain output is high IPG(LKG) | VPG = 5 V | max 100 nA | 6 |
| PG pin output low-level voltage | IPG = 1 mA | max 400 mV | 6 |
| Output discharge current on SW pin | TPS62A01; VIN = 3 V, VOUT = 2.0 V | typ 60 mA | 6 |
| Thermal shutdown threshold TJ(SD) | Temperature rising | typ 170 °C | 6 |
| Thermal shutdown hysteresis TJ(HYS) | typ 20 °C | 6 |
Pins, by the datasheet
6- 1 GND
- Ground pin. · p. 3
- 2 SW
- Switch pin connected to internal FET switches; connect the output filter inductor here. · p. 3
- 3 VIN
- Power supply voltage pin. · p. 3
- 4 EN
- High enables the device; low disables it into shutdown; do not leave floating. · p. 3
- 5 FB
- Feedback input for the internal control loop; connect to an external feedback divider. · p. 3
- 6 PG
- Power-good output; pull up to no more than 5.5 V; leave open or connect to GND if unused. · p. 3
Open-source boards using it
6- 4 layers117.5 × 30 mm

- 4 layers282 × 129 mm

- 4 layers80 × 50 mm

- 4 layers38 × 70 mm

Solar controller
lzptr/solar-controller
ESP32 Based PCB for Controlling a Solar System Light Chain
53 parts - 4 layers50 × 50 mm

- 4 layers88 × 33 mm

Parts like it
8TPS61023DRL
SOT-563-40℃~+125℃@(TJ) 1 1MHz 2.2V~5.5V 3A 3uA 500mV~5.5V Adjustable Boost Boost Built-in Overcurrent Protection、Light load efficient mode、Load disconnect Yes SOT-563 DC-DC Converters ROHSTexas InstrumentsDC-DC ConvertersTPS564247DRL
SOT-563-40℃~+125℃@(TJ) 1 1.2MHz 120uA 3V~16V 4A 600mV~7V Adjustable Buck Buck Built-in Yes SOT-563 DC-DC Converters ROHSTexas InstrumentsDC-DC ConvertersTLV62569ADRL
SOT-563-40℃~+125℃@(TJ) 1 1.5MHz 2.5V~5.5V 2A 600mV~5.5V Adjustable Buck Built-in Overcurrent Protection Step-down type Yes SOT-563 DC-DC Converters ROHSTexas InstrumentsDC-DC ConvertersTLV62585PDRL
SOT-563-40℃~+125℃@(TJ) 1 1.5MHz 2.5V~5.5V 35uA 3A 600mV~5.5V Adjustable Buck Buck Built-in Yes SOT-563 DC-DC Converters ROHSTexas InstrumentsDC-DC ConvertersTPS563203DRL
SOT-563-40℃~+125℃@(TJ) 110uA 3A 4.2V~17V 600kHz 600mV~7V Adjustable Buck Buck Built-in Yes SOT-563 DC-DC Converters ROHSTexas InstrumentsDC-DC ConvertersTPS62A01DRL
SOT-563-40℃~+125℃@(TJ) 1 1A 2.4MHz 2.5V~5.5V 20uA 600mV~5.5V Adjustable Buck Buck Built-in Yes SOT-563 DC-DC Converters ROHSTexas InstrumentsDC-DC ConvertersTPS562202DRL
SOT-6(3x5)-40℃~+125℃@(TJ) 1 2A 4.3V~17V 520uA 580kHz 804mV~7V Adjustable Buck Buck Built-in Yes SOT-6(3x5) DC-DC Converters ROHSTexas InstrumentsDC-DC ConvertersTPS562203DRL
SOT-563-40℃~+125℃@(TJ) 1 110uA 2A 4.2V~17V 600kHz 600mV~7V Adjustable Buck Buck Built-in Yes SOT-563 DC-DC Converters ROHSTexas InstrumentsDC-DC Converters
Questions
Is there a KiCad symbol and footprint for the TPS62A01ADRL?
Yes. The symbol is Regulator_Switching:TPS62A01ADRL and the footprint Package_TO_SOT_SMD:SOT-563, both drawn on this page. PCBKit places them on a board for you when you design with it.
What package is the TPS62A01ADRL?
SOT-563, with 6 pins. Its footprint is drawn on this page.
Where is the TPS62A01ADRL datasheet?
Texas Instruments publishes it: the Datasheet link on this page opens it.
Where can I order the TPS62A01ADRL?
JLCPCB lists it as part C5181455, with 6,571 in stock; the sellers' links on this page open their listings.
What can replace the TPS62A01ADRL?
Parts like it in the library: the TPS61023DRL by Texas Instruments, the TPS564247DRL by Texas Instruments, the TLV62569ADRL by Texas Instruments and the TLV62585PDRL by Texas Instruments. Check their datasheets: a part that fits the footprint may still differ in its ratings.
Which open-source boards use the TPS62A01ADRL?
6 boards in 4 repositories on GitHub; the most starred are listed on this page, with their KiCad files.