
TPS62933ODRL
Texas InstrumentsExtended
-40℃~+150℃@(TJ) 1 2.2MHz 3.8V~30V 3A 45uA 800mV~22V Adjustable Buck Built-in Light load efficient mode、Adjustable soft-start、Operating status indication、Cycle-by-cycle current limiting、Hiccup current limiting、EMI optimization (spread spectrum) Step-down type Yes SOT-583 DC-DC Converters ROHS
- Part id
- ti/TPS62933ODRL
- Category
- DC DC Converters
- Package
- SOT-583
- Pins
- 8
- In stock
- 3,335 at JLCPCB (C6290372)
- Used on
- 1 open-source board
Overview
The TPS62933ODRL is a DC DC Converter made by Texas Instruments in a SOT-583 package with 8 pins. -40℃~+150℃@(TJ) 1 2.2MHz 3.8V~30V 3A 45uA 800mV~22V Adjustable Buck Built-in Light load efficient mode、Adjustable soft-start、Operating status indication、Cycle-by-cycle current limiting、Hiccup current limiting、EMI optimization (spread spectrum) Step-down type Yes SOT-583 DC-DC Converters ROHS.
PCBKit's library has its KiCad symbol (Regulator_Switching:TPS62933, from KiCad's library) and its footprint (Package_TO_SOT_SMD:SOT-583-8, from KiCad's library), ready for a KiCad board. 3,335 are in stock at JLCPCB (part C6290372). 1 open-source board in 1 repository on GitHub use it.
Symbol
Footprint
From the datasheet
17- Supply, least
- 3.8 V · VIN, recommended operating minimum · p. 5
- Supply, most
- 30 V · VIN, recommended operating maximum · p. 5
- Supply, absolute maximum
- 32 V · VIN, absolute maximum · p. 5
- Junction, hottest
- 150 °C · Operating junction temperature maximum · p. 5
- Takes working
- 45 µA · VIN nonswitching quiescent current, typical, EN = 5 V, VFB = 1 V · p. 6
- Takes asleep
- 2 µA · VIN shutdown supply current, typical, VEN = 0 V · p. 6
- Gives
- 3 A · Continuous output current maximum, TPS62933O · p. 3
- Current limit
- 5 A · High-side MOSFET current limit, typical · p. 6
- Feedback reference
- 800 mV · FB reference voltage, typical, TJ = 25°C · p. 6
- Switches at
- 500 kHz · Switching center frequency, typical, RT floating · p. 7
- Switches at
- 1.2 MHz · Switching center frequency, typical, RT = GND · p. 7
- Switches at
- 310 kHz · Switching center frequency, typical, RT = 71.5 kΩ · p. 7
- Switches at
- 2.1 MHz · Switching center frequency, typical, RT = 9.09 kΩ · p. 7
- Junction to air (DRL (SOT583), 8 PINS)
- 112.2 K/W · Junction-to-ambient thermal resistance, JEDEC board · p. 6
- Junction to case (DRL (SOT583), 8 PINS)
- 29.1 K/W · Junction-to-case top thermal resistance, JEDEC board · p. 6
- Junction to board (DRL (SOT583), 8 PINS)
- 19.3 K/W · Junction-to-board thermal resistance, JEDEC board · p. 6
- Junction to air (DRL (SOT583), 8 PINS)
- 60.2 K/W · Junction-to-ambient thermal resistance on official EVM board · p. 6
What it is and has
8- Input voltage range
- 3.8 V to 30 V · p. 1
- Output voltage range
- 0.8 V to 22 V · p. 1
- Reference voltage
- 0.8 V ± 1% at 25°C · p. 1
- Maximum duty cycle
- 98% · p. 1
- Selectable switching frequency
- 200 kHz to 2.2 MHz · p. 1
- Light-load operation
- Out-of-audio (OOA) · p. 1
- Prebiased startup
- Supported · p. 1
- Package
- 1.6 mm × 2.1 mm SOT583 · p. 1
Around it
1- cap 100-nF
- between BST and SW; High-quality ceramic bootstrap capacitor for the high-side FET driver. · p. 3
Specifications
74| Parameter | Conditions | As printed | Page |
|---|---|---|---|
| Input voltage | VIN | min -0.3 · max 32 V | 5 |
| Input voltage | EN | min -0.3 · max 6 V | 5 |
| Input voltage | FB | min -0.3 · max 6 V | 5 |
| Output voltage | SW, DC | min -0.3 · max 32 V | 5 |
| Output voltage | SW, transient < 10 ns | min -3 · max 33 V | 5 |
| Output voltage | BST; maximum is SW + 6 V | min -0.3 V | 5 |
| Output voltage | BST–SW | min -0.3 · max 6 V | 5 |
| Output voltage | SS/PG; PG for TPS62933O | min -0.3 · max 6 V | 5 |
| Output voltage | RT | min -0.3 · max 6 V | 5 |
| Operating junction temperature(2) TJ | min -40 · max 150 °C | 5 | |
| Storage temperature Tstg | min -65 · max 150 °C | 5 | |
| Electrostatic discharge V(ESD) | Human body model (HBM), per ANSI/ESDA/JEDEC JS-001, all pins; ±2000 V | max 2000 V | 5 |
| Electrostatic discharge V(ESD) | Charged device model (CDM), per ANSI/ESDA/JEDEC JS-002, all pins; ±500 V | max 500 V | 5 |
| Input voltage | VIN | min 3.8 · max 30 V | 5 |
| Input voltage | EN | min -0.1 · max 5.5 V | 5 |
| Input voltage | FB | min -0.1 · max 5.5 V | 5 |
| Input voltage | PG | min -0.1 · max 5.5 V | 5 |
| Output voltage | VOUT | min 0.8 · max 22 V | 5 |
| Output voltage | SW, DC | min -0.1 · max 30 V | 5 |
| Output voltage | SW, transient < 10 ns | min -3 · max 32 V | 5 |
| Output voltage | BST; maximum is SW + 5.5 V | min -0.1 V | 5 |
| Output voltage | BST-SW | min -0.1 · max 5.5 V | 5 |
| Ouput current IOUT | TPS62933, TPS62933x; applies to TPS62933O | min 0 · max 3 A | 5 |
| Operating junction temperature, TJ TJ | min -40 · max 150 °C | 5 | |
| Junction-to-ambient thermal resistance RθJA | DRL (SOT583), 8 PINS; JEDEC | typ 112.2 °C/W | 6 |
| Junction-to-case (top) thermal resistance RθJC(top) | DRL (SOT583), 8 PINS; JEDEC | typ 29.1 °C/W | 6 |
| Junction-to-board thermal resistance RθJB | DRL (SOT583), 8 PINS; JEDEC | typ 19.3 °C/W | 6 |
| Junction-to-top characterization parameter ΨJT | DRL (SOT583), 8 PINS; JEDEC | typ 1.6 °C/W | 6 |
| Junction-to-board characterization parameter ΨJB | DRL (SOT583), 8 PINS; JEDEC | typ 19.2 °C/W | 6 |
| Junction-to-ambient thermal resistance on official EVM board RθJA_EVM | DRL (SOT583), 8 PINS; EVM | typ 60.2 °C/W | 6 |
| Operation input voltage VIN | min 3.8 · max 30 V | 6 | |
| Nonswitching quiescent current IQ | EN = 5 V, VFB = 1 V, TPS62933O | typ 45 uA | 6 |
| Shutdown supply current ISHDN | VEN = 0 V | typ 2 uA | 6 |
| Input undervoltage lockout thresholds VIN_UVLO | Rising threshold | min 3.4 · typ 3.6 · max 3.8 V | 6 |
| Input undervoltage lockout thresholds VIN_UVLO | Falling threshold | min 3.1 · typ 3.3 · max 3.5 V | 6 |
| Input undervoltage lockout thresholds VIN_UVLO | Hysteresis | typ 300 mV | 6 |
| Enable threshold VEN_RISE | Rising enable threshold | typ 1.21 · max 1.28 V | 6 |
| Disable threshold VEN_FALL | Falling disable threshold | min 1.1 · typ 1.17 V | 6 |
| EN pullup current Ip | VEN = 1.0 V | typ 0.7 uA | 6 |
| EN pullup hysteresis current Ih | VEN = 1.5 V | typ 1.4 uA | 6 |
| FB voltage VFB | TJ = 25°C | min 792 · typ 800 · max 808 mV | 6 |
| FB voltage VFB | TJ = 0°C to 85°C | min 788 · typ 800 · max 812 mV | 6 |
| FB voltage VFB | TJ = –40°C to 150°C | min 784 · typ 800 · max 816 mV | 6 |
| Input leakage current IFB | VFB = 0.8 V | max 0.15 uA | 6 |
| High-side MOSFET on-resistance RDSON_HS | TJ = 25°C, VBST – SW = 5 V | typ 76 mΩ | 6 |
| Low-side MOSFET on-resistance RDSON_LS | TJ = 25°C | typ 32 mΩ | 6 |
| High-side MOSFET current limit IHS_LIMIT | TPS62933 and TPS62933x; applies to TPS62933O | min 4.2 · typ 5 · max 5.8 A | 6 |
| Low-side MOSFET current limit ILS_LIMIT | TPS62933 and TPS62933x; applies to TPS62933O | min 2.9 · typ 3.8 · max 4.5 A | 7 |
| Minimum peak inductor current IPEAK_MIN | TPS62933, TPS62933P, and TPS62933O | typ 0.75 A | 7 |
| Fixed internal soft-start time TSS | TPS62933P and TPS62933O | typ 2 ms | 7 |
| PG threshold, VFB percentage VPGTH | VFB falling, PG high to low | typ 85 % | 7 |
| PG threshold, VFB percentage VPGTH | VFB rising, PG low to high | typ 90 % | 7 |
| PG threshold, VFB percentage VPGTH | VFB falling, PG low to high | typ 110 % | 7 |
| PG threshold, VFB percentage VPGTH | VFB rising, PG high to low | typ 115 % | 7 |
| PG delay time TPG_R | PG from low to high | typ 70 us | 7 |
| PG delay time TPG_F | PG from high to low | typ 18 us | 7 |
| Minimum VIN for valid PG output VIN_PG_VALID | Measured when PG < 0.5 V with 100-kΩ pullup to external 5 V | typ 2 · max 2.5 V | 7 |
| PG output low-level voltage VPG_OL | IPG = 0.5 mA | max 0.3 V | 7 |
| PG leakage current when open drain is high IPG_LK | VPG = 5.5 V | min -1 · max 1 uA | 7 |
| Switching center frequency fSW | RT = floating | min 450 · typ 500 · max 550 kHz | 7 |
| Switching center frequency fSW | RT = GND | min 1000 · typ 1200 · max 1350 kHz | 7 |
| Switching center frequency fSW | RT = 71.5 kΩ | typ 310 kHz | 7 |
| Switching center frequency fSW | RT = 9.09 kΩ | typ 2100 kHz | 7 |
| Minimum switching frequency fSW_min | TPS62933O | typ 30 kHz | 7 |
| Minimum ON pulse width tON_MIN | Not production tested, specified by design | typ 70 ns | 7 |
| Minimum OFF pulse width tOFF_MIN | Not production tested, specified by design | typ 140 ns | 7 |
| Maximum ON pulse width tON_MAX | Not production tested, specified by design | typ 7 us | 7 |
| Output OVP threshold VOVP | OVP detect (L→H) | min 112 · typ 115 · max 118 % | 7 |
| Output OVP threshold VOVP | Hysteresis | typ 5 % | 7 |
| Output UVP threshold VUVP | UVP detect (H→L) | typ 65 % | 7 |
| UV hiccup ON time before entering hiccup mode after soft start ends thiccup_ON | typ 256 us | 7 | |
| Thermal shutdown threshold TSHDN | Shutdown temperature; not production tested, specified by design | typ 165 °C | 7 |
| Hysteresis THYS | Thermal shutdown; not production tested, specified by design | typ 30 °C | 7 |
| Internal spread oscillator frequency fspread | Typical spread is ±6% | typ 6 % | 8 |
Pins, by the datasheet
8- 1 RT
- Frequency programming input; float for 500 kHz, tie to GND for 1.2 MHz, or connect a timing resistor. · p. 3
- 2 EN
- Drive high or leave floating to enable; an external resistor divider can implement adjustable VIN UVLO. · p. 3
- 3 VIN
- Supply input to internal LDO and high-side FET; connect bypass capacitors directly between VIN and GND. · p. 3
- 4 GND
- Connect to system ground and the ground sides of CIN and COUT; keep the path to CIN as short as possible. · p. 3
- 5 SW
- Switching output connected internally to the high-side FET source and low-side FET drain; connect to the power inductor. · p. 3
- 6 BST
- Bootstrap capacitor connection for the high-side FET driver; connect a high-quality 100-nF ceramic capacitor to SW. · p. 3
- 7 PG
- Power-good indicator. · p. 3
- 8 FB
- Feedback voltage input. · p. 3
Open-source boards using it
1- 8 layers136.9 × 155.9 mm

Parts like it
6TPS62933DRL
SOT-583-40℃~+150℃@(TJ) 1 12uA 2.2MHz 3.8V~30V 3A 800mV~22V Adjustable Buck Buck Built-in Yes SOT-583 DC-DC Converters ROHSTexas InstrumentsDC-DC ConvertersTPS62933FDRL
SOT-583-40℃~+150℃@(TJ) 1 125uA 2.2MHz 3.8V~30V 3A 800mV~22V Adjustable Buck Buck Built-in Yes SOT-583 DC-DC Converters ROHSTexas InstrumentsDC-DC ConvertersTPS62933PDRL
SOT-583-40℃~+150℃@(TJ) 1 125uA 200kHz~2.2MHz 3.8V~30V 3A 800mV~22V Adjustable Buck Buck Built-in Yes SOT-583 DC-DC Converters ROHSTexas InstrumentsDC-DC ConvertersTPS563300DRL
SOT-583-40℃~+150℃@(TJ) 1 20uA 3.8V~28V 3A 500kHz 800mV~22V Adjustable Buck Built-in Overcurrent Protection、Light load efficient mode、Cycle-by-cycle current limiting、Hiccup current limiting、EMI optimization (spread spectrum) Step-down type Yes SOT-583 DC-DC Converters ROHSTexas InstrumentsDC-DC ConvertersTPS628303ADRL
SOT-583-8-40℃~+125℃@(TJ) 1 2.25V~5.5V 2MHz 3A 500mV~4.5V 7uA Adjustable Buck Buck Built-in Yes SOT-583-8 DC-DC Converters ROHSTexas InstrumentsDC-DC ConvertersTPS610333DRL
SOT-583-8-40℃~+125℃@(TJ) 1 1.8V~5.5V 2.4MHz Boost Built-in Yes SOT-583-8 DC-DC Converters ROHSTexas InstrumentsDC-DC Converters
Questions
Is there a KiCad symbol and footprint for the TPS62933ODRL?
Yes. The symbol is Regulator_Switching:TPS62933 and the footprint Package_TO_SOT_SMD:SOT-583-8, both drawn on this page. PCBKit places them on a board for you when you design with it.
What package is the TPS62933ODRL?
SOT-583, with 8 pins. Its footprint is drawn on this page.
Where is the TPS62933ODRL datasheet?
Texas Instruments publishes it: the Datasheet link on this page opens it.
Where can I order the TPS62933ODRL?
JLCPCB lists it as part C6290372, with 3,335 in stock; the sellers' links on this page open their listings.
What can replace the TPS62933ODRL?
Parts like it in the library: the TPS62933DRL by Texas Instruments, the TPS62933FDRL by Texas Instruments, the TPS62933PDRL by Texas Instruments and the TPS563300DRL by Texas Instruments. Check their datasheets: a part that fits the footprint may still differ in its ratings.
Which open-source boards use the TPS62933ODRL?
1 board in 1 repository on GitHub; the most starred are listed on this page, with their KiCad files.