
TPS62933FDRL
Texas InstrumentsExtended
-40℃~+150℃@(TJ) 1 125uA 2.2MHz 3.8V~30V 3A 800mV~22V Adjustable Buck Buck Built-in Yes SOT-583 DC-DC Converters ROHS
- Part id
- ti/TPS62933FDRL
- Category
- DC DC Converters
- Package
- SOT-583
- Pins
- 8
- In stock
- 3,178 at JLCPCB (C5219272)
- Used on
- 4 open-source boards
Overview
The TPS62933FDRL is a DC DC Converter made by Texas Instruments in a SOT-583 package with 8 pins. -40℃~+150℃@(TJ) 1 125uA 2.2MHz 3.8V~30V 3A 800mV~22V Adjustable Buck Buck Built-in Yes SOT-583 DC-DC Converters ROHS.
PCBKit's library has its KiCad symbol (Regulator_Switching:TPS62933, from KiCad's library) and its footprint (Package_TO_SOT_SMD:SOT-583-8, from KiCad's library), ready for a KiCad board. 3,178 are in stock at JLCPCB (part C5219272). 4 open-source boards in 3 repositories on GitHub use it.
Symbol
Footprint
From the datasheet
17- Supply, least
- 3.8 V · VIN, recommended operating min · p. 5
- Supply, most
- 30 V · VIN, recommended operating max · p. 5
- Supply, absolute maximum
- 32 V · VIN, absolute max · p. 5
- Junction, hottest
- 150 °C · Operating junction temperature max · p. 5
- Takes working
- 125 µA · VIN nonswitching quiescent current, EN = 5 V, VFB = 1 V, typical · p. 6
- Takes asleep
- 2 µA · Shutdown supply current, VEN = 0 V, typical · p. 6
- Gives
- 3 A · Continuous output current max · p. 3
- Current limit
- 5 A · High-side MOSFET current limit, typical · p. 6
- Feedback reference
- 800 mV · FB reference voltage, TJ = 25°C, typical · p. 6
- Switches at
- 500 kHz · RT floating, typical · p. 7
- Switches at
- 1.2 MHz · RT = GND, typical · p. 7
- Switches at
- 310 kHz · RT = 71.5 kΩ, typical · p. 7
- Switches at
- 2.1 MHz · RT = 9.09 kΩ, typical · p. 7
- Junction to air (DRL (SOT583), 8 PINS)
- 112.2 K/W · JEDEC board, typical; comparison only · p. 6
- Junction to air (DRL (SOT583), 8 PINS)
- 60.2 K/W · Official EVM board, typical · p. 6
- Junction to case (DRL (SOT583), 8 PINS)
- 29.1 K/W · Junction-to-case top, JEDEC, typical · p. 6
- Junction to board (DRL (SOT583), 8 PINS)
- 19.3 K/W · Junction-to-board, JEDEC, typical · p. 6
What it is and has
13- Input voltage range
- 3.8 V to 30 V · p. 1
- Output voltage range
- 0.8 V to 22 V · p. 1
- Integrated MOSFETs
- 76 mΩ high-side, 32 mΩ low-side · p. 1
- Reference accuracy
- 0.8 V ± 1% at 25°C · p. 1
- Maximum duty cycle
- 98% · p. 1
- Operating mode
- Forced continuous current modulation (FCCM), 3 A output, SS pin · p. 3
- Switching frequency
- 200 kHz to 2.2 MHz selectable · p. 1
- Prebiased startup
- Supported · p. 1
- Protection
- Non-latched OTP, OCP, OVP, UVP, UVLO · p. 1
- Package
- 1.6 mm × 2.1 mm SOT583 · p. 1
- Integrated MOSFETs
- 76 mΩ and 32 mΩ · p. 1
- Light-load operation
- forced continuous conduction mode (FCCM) · p. 26
- Enable
- Precision EN threshold · p. 1
Around it
10- cap 100-nF
- between BST and SW; High-quality ceramic bootstrap capacitor for the high-side FET driver. · p. 3
- res 10 kΩ
- between FB and GND; RFBB, bottom feedback divider resistor; use 1% tolerance and low temperature coefficient. · p. 19
- res 10 kΩ to 300 kΩ
- between VOUT and FB; RFBT, top feedback divider resistor; select for the desired output voltage with RFBB = 10 kΩ. · p. 19
- cap 6.8 nF minimum
- between SS and GND; SS must not float; place the capacitor close to the IC. · p. 29
- cap 33 nF
- between SS and GND; Example C4 sets soft-start time to approximately 5 ms. · p. 29
- cap 0.1 µF
- between BST and SW; Ceramic, X5R or better dielectric, rated at least 16 V; place close to BST and SW. · p. 29
- res < 10 Ω
- between BST and bootstrap capacitor; Series bootstrap resistor R4 reduces SW voltage spikes. · p. 29
- cap 10 μF
- between VIN and GND; Typical recommended input decoupling capacitance; account for DC bias and use X5R or X7R ceramic dielectric. · p. 32
- cap 100 nF
- between VIN and GND; Connect directly to the device pins for high frequency filtering. · p. 38
- cap 10 pF
- between VOUT and FB; Optional example feedforward capacitor C9 across the upper feedback resistor to improve load transient performance. · p. 33
Specifications
62| Parameter | Conditions | As printed | Page |
|---|---|---|---|
| Input voltage VIN | min -0.3 · max 32 V | 5 | |
| Input voltage EN | min -0.3 · max 6 V | 5 | |
| Input voltage FB | min -0.3 · max 6 V | 5 | |
| Output voltage SW | DC | min -0.3 · max 32 V | 5 |
| Output voltage SW | transient < 10 ns | min -3 · max 33 V | 5 |
| Output voltage BST | Maximum is SW + 6 V | min -0.3 V | 5 |
| Output voltage BST–SW | min -0.3 · max 6 V | 5 | |
| Output voltage SS | TPS62933F; SS/PG row | min -0.3 · max 6 V | 5 |
| Output voltage RT | min -0.3 · max 6 V | 5 | |
| Operating junction temperature TJ | min -40 · max 150 °C | 5 | |
| Storage temperature Tstg | min -65 · max 150 °C | 5 | |
| Electrostatic discharge V(ESD) | Human body model (HBM), per ANSI/ESDA/JEDEC JS-001, all pins; ±2000 V | max 2000 V | 5 |
| Electrostatic discharge V(ESD) | Charged device model (CDM), per ANSI/ESDA/JEDEC JS-002, all pins; ±500 V | max 500 V | 5 |
| Input voltage VIN | min 3.8 · max 30 V | 5 | |
| Input voltage EN | min -0.1 · max 5.5 V | 5 | |
| Input voltage FB | min -0.1 · max 5.5 V | 5 | |
| Output voltage VOUT | min 0.8 · max 22 V | 5 | |
| Output voltage SW | DC | min -0.1 · max 30 V | 5 |
| Output voltage SW | transient < 10 ns | min -3 · max 32 V | 5 |
| Output voltage BST | Maximum is SW + 5.5 V | min -0.1 V | 5 |
| Output voltage BST-SW | min -0.1 · max 5.5 V | 5 | |
| Ouput current IOUT | TPS62933, TPS62933x | min 0 · max 3 A | 5 |
| Temperature TJ | Operating junction temperature | min -40 · max 150 °C | 5 |
| Junction-to-ambient thermal resistance RθJA | DRL (SOT583), 8 PINS; JEDEC | typ 112.2 °C/W | 6 |
| Junction-to-case (top) thermal resistance RθJC(top) | DRL (SOT583), 8 PINS; JEDEC | typ 29.1 °C/W | 6 |
| Junction-to-board thermal resistance RθJB | DRL (SOT583), 8 PINS; JEDEC | typ 19.3 °C/W | 6 |
| Junction-to-top characterization parameter ΨJT | DRL (SOT583), 8 PINS; JEDEC | typ 1.6 °C/W | 6 |
| Junction-to-board characterization parameter ΨJB | DRL (SOT583), 8 PINS; JEDEC | typ 19.2 °C/W | 6 |
| Junction-to-ambient thermal resistance on official EVM board RθJA_EVM | DRL (SOT583), 8 PINS; EVM | typ 60.2 °C/W | 6 |
| Operation input voltage VIN | min 3.8 · max 30 V | 6 | |
| Nonswitching quiescent current IQ | EN = 5 V, VFB = 1 V, TPS62933F | typ 125 uA | 6 |
| Shutdown supply current ISHDN | VEN = 0 V | typ 2 uA | 6 |
| Input undervoltage lockout thresholds VIN_UVLO | Rising threshold | min 3.4 · typ 3.6 · max 3.8 V | 6 |
| Input undervoltage lockout thresholds VIN_UVLO | Falling threshold | min 3.1 · typ 3.3 · max 3.5 V | 6 |
| Input undervoltage lockout thresholds VIN_UVLO | Hysteresis | typ 300 mV | 6 |
| Enable threshold VEN_RISE | Rising enable threshold | typ 1.21 · max 1.28 V | 6 |
| Disable threshold VEN_FALL | Falling disable threshold | min 1.1 · typ 1.17 V | 6 |
| EN pullup current Ip | VEN = 1.0 V | typ 0.7 uA | 6 |
| EN pullup hysteresis current Ih | VEN = 1.5 V | typ 1.4 uA | 6 |
| FB voltage VFB | TJ = 25°C | min 792 · typ 800 · max 808 mV | 6 |
| FB voltage VFB | TJ = 0°C to 85°C | min 788 · typ 800 · max 812 mV | 6 |
| FB voltage VFB | TJ = –40°C to 150°C | min 784 · typ 800 · max 816 mV | 6 |
| Input leakage current IFB | VFB = 0.8 V | max 0.15 uA | 6 |
| High-side MOSFET on-resistance RDSON_HS | TJ = 25°C, VBST – SW = 5 V | typ 76 mΩ | 6 |
| Low-side MOSFET on-resistance RDSON_LS | TJ = 25°C | typ 32 mΩ | 6 |
| High-side MOSFET current limit IHS_LIMIT | TPS62933 and TPS62933x | min 4.2 · typ 5 · max 5.8 A | 6 |
| Low-side MOSFET current limit ILS_LIMIT | TPS62933 and TPS62933x | min 2.9 · typ 3.8 · max 4.5 A | 7 |
| Reverse current limit ILS_NOC | TPS62933F | min 1.2 · typ 2.4 · max 3.6 A | 7 |
| Soft-start charge current ISS | TPS62932, TPS62933, and TPS62933F | min 4.5 · typ 5.5 · max 6.5 uA | 7 |
| Switching center frequency fSW | RT = floating | min 450 · typ 500 · max 550 kHz | 7 |
| Switching center frequency fSW | RT = GND | min 1000 · typ 1200 · max 1350 kHz | 7 |
| Switching center frequency fSW | RT = 71.5 kΩ | typ 310 kHz | 7 |
| Switching center frequency fSW | RT = 9.09 kΩ | typ 2100 kHz | 7 |
| Minimum ON pulse width tON_MIN | Not production tested, specified by design | typ 70 ns | 7 |
| Minimum OFF pulse width tOFF_MIN | Not production tested, specified by design | typ 140 ns | 7 |
| Maximum ON pulse width tON_MAX | Not production tested, specified by design | typ 7 us | 7 |
| Output OVP threshold VOVP | OVP detect (L→H) | min 112 · typ 115 · max 118 % | 7 |
| Output OVP threshold VOVP | Hysteresis | typ 5 % | 7 |
| Output UVP threshold VUVP | UVP detect (H→L) | typ 65 % | 7 |
| UV hiccup ON time before entering hiccup mode after soft start ends thiccup_ON | typ 256 us | 7 | |
| Thermal shutdown threshold TSHDN | Shutdown temperature; not production tested, specified by design | typ 165 °C | 7 |
| Hysteresis THYS | Thermal shutdown; not production tested, specified by design | typ 30 °C | 7 |
Pins, by the datasheet
8- 1 RT
- Frequency programming input; float for 500 kHz, tie to GND for 1.2 MHz, or connect an RT timing resistor. · p. 3
- 2 EN
- Drive high or leave floating to enable; an external resistor divider can implement adjustable VIN undervoltage lockout. · p. 3
- 3 VIN
- Supply input to internal LDO and high-side FET; connect input bypass capacitors directly between VIN and GND. · p. 3
- 4 GND
- Controller and low-side FET ground; connect to system ground and CIN and COUT grounds, with the shortest possible path to CIN. · p. 3
- 5 SW
- Switching output connected internally to the high-side FET source and low-side FET drain; connect to the power inductor. · p. 3
- 6 BST
- High-side FET driver bootstrap connection; connect a high-quality 100-nF ceramic capacitor to SW. · p. 3
- 7 SS
- External capacitor adjusts soft-start time. · p. 3
- 8 FB
- Voltage reference feedback pin. · p. 3
Ordering codes, by the datasheet
2- TPS62933FDRLR
- SOT-5X3 (DRL) · 8 pins; 4000-piece LARGE T&R; lead finish Call TI | Sn; marking 933F · p. 44
- TPS62933FDRLR.A
- SOT-5X3 (DRL) · 8 pins; 4000-piece LARGE T&R; lead finish SN; marking 933F · p. 44
Open-source boards using it
4- 2 layers168 × 44 mm

- 4 layers

RasterGenerator
LukasReil/SEM_Dev
This project describes a fully open-source electron microscope.
15 parts - 2 layers60 × 50 mm

ESP32-P4-CAM MAIN
momszx/esp32-p4-cam
ESP32-P4 compact WiFi streaming camera - KiCad 10 hardware (MAIN rev A, 4-layer 45x45 mm) and design docs
127 parts - 4 layers45 × 45 mm

ESP32-P4-CAM MAIN
momszx/esp32-p4-cam
ESP32-P4 compact WiFi streaming camera - KiCad 10 hardware (MAIN rev A, 4-layer 45x45 mm) and design docs
120 parts
Parts like it
6TPS62933DRL
SOT-583-40℃~+150℃@(TJ) 1 12uA 2.2MHz 3.8V~30V 3A 800mV~22V Adjustable Buck Buck Built-in Yes SOT-583 DC-DC Converters ROHSTexas InstrumentsDC-DC ConvertersTPS62933ODRL
SOT-583-40℃~+150℃@(TJ) 1 2.2MHz 3.8V~30V 3A 45uA 800mV~22V Adjustable Buck Built-in Light load efficient mode、Adjustable soft-start、Operating status indication、Cycle-by-cycle current limiting、Hiccup current limiting、EMI optimization (spread spectrum) Step-down type Yes SOT-583 DC-DC Converters ROHSTexas InstrumentsDC-DC ConvertersTPS62933PDRL
SOT-583-40℃~+150℃@(TJ) 1 125uA 200kHz~2.2MHz 3.8V~30V 3A 800mV~22V Adjustable Buck Buck Built-in Yes SOT-583 DC-DC Converters ROHSTexas InstrumentsDC-DC ConvertersTPS563300DRL
SOT-583-40℃~+150℃@(TJ) 1 20uA 3.8V~28V 3A 500kHz 800mV~22V Adjustable Buck Built-in Overcurrent Protection、Light load efficient mode、Cycle-by-cycle current limiting、Hiccup current limiting、EMI optimization (spread spectrum) Step-down type Yes SOT-583 DC-DC Converters ROHSTexas InstrumentsDC-DC ConvertersTPS628303ADRL
SOT-583-8-40℃~+125℃@(TJ) 1 2.25V~5.5V 2MHz 3A 500mV~4.5V 7uA Adjustable Buck Buck Built-in Yes SOT-583-8 DC-DC Converters ROHSTexas InstrumentsDC-DC ConvertersTPS610333DRL
SOT-583-8-40℃~+125℃@(TJ) 1 1.8V~5.5V 2.4MHz Boost Built-in Yes SOT-583-8 DC-DC Converters ROHSTexas InstrumentsDC-DC Converters
Questions
Is there a KiCad symbol and footprint for the TPS62933FDRL?
Yes. The symbol is Regulator_Switching:TPS62933 and the footprint Package_TO_SOT_SMD:SOT-583-8, both drawn on this page. PCBKit places them on a board for you when you design with it.
What package is the TPS62933FDRL?
SOT-583, with 8 pins. Its footprint is drawn on this page.
Where is the TPS62933FDRL datasheet?
Texas Instruments publishes it: the Datasheet link on this page opens it.
Where can I order the TPS62933FDRL?
JLCPCB lists it as part C5219272, with 3,178 in stock; the sellers' links on this page open their listings.
What can replace the TPS62933FDRL?
Parts like it in the library: the TPS62933DRL by Texas Instruments, the TPS62933ODRL by Texas Instruments, the TPS62933PDRL by Texas Instruments and the TPS563300DRL by Texas Instruments. Check their datasheets: a part that fits the footprint may still differ in its ratings.
Which open-source boards use the TPS62933FDRL?
4 boards in 3 repositories on GitHub; the most starred are listed on this page, with their KiCad files.