Skip to the content
12345

TPS2051CDBV

Texas InstrumentsExtended

-40℃~+125℃ 1 4.5V~5.5V 500mA 97mΩ Active High Low Side Switch Short-Circuit Protection(SCP)、Overcurrent Protection(OCP)、Overtemperature protection (OTP) SOT-23-5 Power Distribution Switches ROHS

Part id
ti/TPS2051CDBV
Category
Power Distribution Switches
Package
SOT-23-5
Pins
5
In stock
15,916 at JLCPCB (C129581)
Used on
18 open-source boards

Overview

The TPS2051CDBV is a power Distribution Switche made by Texas Instruments in a SOT-23-5 package with 5 pins. -40℃~+125℃ 1 4.5V~5.5V 500mA 97mΩ Active High Low Side Switch Short-Circuit Protection(SCP)、Overcurrent Protection(OCP)、Overtemperature protection (OTP) SOT-23-5 Power Distribution Switches ROHS.

PCBKit's library has its KiCad symbol (Power_Management:TPS2051CDBV, from KiCad's library) and its footprint (Package_TO_SOT_SMD:SOT-23-5, from KiCad's library), ready for a KiCad board. 15,916 are in stock at JLCPCB (part C129581). 18 open-source boards in 16 repositories on GitHub use it.

Symbol

1OUT2GND3FLT4EN5IN
Power_Management:TPS2051CDBVFrom KiCad's library

Footprint

12345
Package_TO_SOT_SMD:SOT-23-5From KiCad's library

From the datasheet

14
Supply, least
4.5 V · IN, recommended operating min · p. 5
Supply, most
5.5 V · IN, recommended operating max · p. 5
Supply, absolute maximum
6 V · IN, absolute maximum · p. 5
Works from
-40 °C · Ambient temperature min · p. 1
Works up to
85 °C · Ambient temperature max · p. 1
Junction, hottest
125 °C · Operating junction temperature max · p. 5
Gives
500 mA · Continuous output current max, TPS2051C · p. 5
Current limit
850 mA · Current limit typical, 0.5-A rated output · p. 8
Takes working
65 µA · IN, switch enabled typical, no load · p. 8
Takes at most
90 µA · IN, switch enabled max, no load · p. 8
Takes asleep
10 nA · IN, switch disabled typical, no load · p. 8
Junction to air (DBV (SOT-23))
224.9 K/W · Junction-to-ambient thermal resistance, 0.5-A rated device · p. 6
Junction to case (DBV (SOT-23))
95.2 K/W · Junction-to-case top thermal resistance, 0.5-A rated device · p. 6
Junction to board (DBV (SOT-23))
51.4 K/W · Junction-to-board thermal resistance, 0.5-A rated device · p. 6

What it is and has

9
Power switches
Single · p. 1
Current limit accuracy
±20%, fixed, constant current limit · p. 1
Overcurrent response
2µs · p. 1
Fault reporting
Deglitched · p. 1
Protection
Reverse current blocking · p. 1
Soft start
Built-in · p. 1
Approvals
UL Listed and CB-File No. E169910 · p. 1
Enable
Active high · p. 3
Output discharge
Yes · p. 3

Around it

1
cap 0.1-µF or greater
between IN and GND; Ceramic; place close to the IC. · p. 4

Specifications

48
ParameterConditionsAs printedPage
Voltage on IN, OUT, EN or EN, FLT (4)Over operating free-air temperature range; referenced to GNDmin -0.3 · max 6 V5
Voltage from IN to OUTOver operating free-air temperature rangemin -6 · max 6 V5
Storage temperature, Tstg Tstgmin -60 · max 150 °C5
Electrostatic discharge V(ESD)Human-body model (HBM), per ANSI/ESDA/JEDEC JS-001min -2000 · max 2000 V5
Electrostatic discharge V(ESD)Charged-device model (CDM), per JEDEC specification JESD22-C101min -500 · max 500 V5
Electrostatic discharge V(ESD)IEC 61000-4-2 contact dischargemin -8000 · max 8000 V5
Electrostatic discharge V(ESD)IEC 61000-4-2 air-gap dischargemin -15000 · max 15000 V5
Input voltage, IN VINmin 4.5 · max 5.5 V5
Input voltage, EN or EN VENmin 0 · max 5.5 V5
High-level input voltage, EN or EN VIHmin 2 V5
Low-level input voltage, EN or EN VILmax 0.7 V5
Continuous output current, OUT(1) IOUTTPS2051Cmax 0.5 A5
Operating junction temperature TJmin -40 · max 125 °C5
Sink current into FLT IFLTmin 0 · max 5 mA5
Junction-to-ambient thermal resistance RθJADBV (SOT-23), 5 pins, rated at 0.5 A or 1 Atyp 224.9 °C/W6
Junction-to-case (top) thermal resistance RθJCtopDBV (SOT-23), 5 pins, rated at 0.5 A or 1 Atyp 95.2 °C/W6
Junction-to-board thermal resistance RθJBDBV (SOT-23), 5 pins, rated at 0.5 A or 1 Atyp 51.4 °C/W6
Junction-to-top characterization parameter ψJTDBV (SOT-23), 5 pins, rated at 0.5 A or 1 Atyp 6.6 °C/W6
Junction-to-board characterization parameter ψJBDBV (SOT-23), 5 pins, rated at 0.5 A or 1 Atyp 50.3 °C/W6
See Power Dissipation and Junction Temperature RθJACustomDBV (SOT-23), 5 pins, rated at 0.5 A or 1 Atyp 139.3 °C/W6
Input – output resistance RDS(on)TPS2051C, DBV, 0.5-A rated output, 25°C; VIN = 5 Vtyp 97 · max 110 mΩ7
Input – output resistance RDS(on)TPS2051C, DBV, 0.5-A rated output, –40°C ≤ (TJ , TA) ≤ 85°C; VIN = 5 Vtyp 96 · max 130 mΩ7
Current limit, See Figure 6-6 IOSTPS2051C, 0.5-A rated output, TPS20xxC; VIN = 5 Vmin 0.67 · typ 0.85 · max 1.01 A7
Supply current, switch disabled ISDVIN = 5 V, IOUT = 0 Atyp 0.01 · max 1 uA7
Supply current, switch disabled ISD–40°C ≤ (TJ , TA) ≤ 85°C, VIN = 5.5 V, IOUT = 0 Amax 2 uA7
Supply current, switch enabled ISEVIN = 5 V, IOUT = 0 Atyp 60 · max 70 uA7
Supply current, switch enabled ISE–40°C ≤ (TJ , TA) ≤ 85°C, VIN = 5.5 V, IOUT = 0 Amax 85 uA7
Reverse leakage current IREVVOUT = 5 V, VIN = 0 V, measure IVOUTtyp 0.1 · max 1 uA7
Output pulldown resistance(2) RPDVIN = VOUT = 5 V, disabled; TPS2051C, TPS20xxCmin 400 · typ 470 · max 600 Ω7
Input – output resistance RDS(ON)TPS2051C, DBV, 0.5-A rated output; 4.5 V ≤ VIN ≤ 5.5 Vtyp 97 · max 154 mΩ8
ThresholdENABLE INPUT (EN or EN), input risingmin 1 · typ 1.45 · max 2 V8
HysteresisENABLE INPUT (EN or EN)min 0.07 · typ 0.13 · max 0.2 V8
Leakage currentENABLE INPUT (EN or EN), (VEN or VEN ) = 0 V or 5.5 Vmin -1 · typ 0 · max 1 uA8
Current limit, See Figure 8-1 IOSTPS2051C, 0.5-A rated output, TPS20xxCmin 0.65 · typ 0.85 · max 1.05 A8
Short-circuit response time(2) tIOSVIN = 5 V; one-half full load → RSHORT = 50 mΩ; measure from application to when current falls below 120% of final valuetyp 2 us8
Supply current, switch disabled ISDIOUT = 0 Atyp 0.01 · max 10 uA8
Supply current, switch enabled ISEIOUT = 0 Atyp 65 · max 90 uA8
Reverse leakage current IREVVOUT = 5.5 V, VIN = 0 V, measure IVOUTtyp 0.2 · max 20 uA8
Rising threshold VUVLOUNDERVOLTAGE LOCKOUT, VIN↑min 3.5 · typ 3.75 · max 4 V8
Hysteresis(2)UNDERVOLTAGE LOCKOUT, VIN↓typ 0.14 V8
Output low voltage, FLTIFLT = 1 mAmax 0.2 V8
OFF-state leakageVFLT = 5.5 Vmax 1 uA8
FLT deglitch tFLTFLT assertion or deassertion deglitchmin 6 · typ 9 · max 12 ms8
Output pulldown resistance RPDVIN = 4 V, VOUT = 5 V, disabled; TPS2051C, TPS20XXCmin 350 · typ 560 · max 1200 Ω8
Output pulldown resistance RPDVIN = 5 V, VOUT = 5 V, disabled; TPS2051C, TPS20XXCmin 300 · typ 470 · max 800 Ω8
Rising threshold (TJ)THERMAL SHUTDOWN, in current limitmin 135 °C8
Rising threshold (TJ)THERMAL SHUTDOWN, not in current limitmin 155 °C8
Hysteresis (2)THERMAL SHUTDOWNtyp 20 °C8

Pins, by the datasheet

5
1 OUT
Power-switch output, connect to load. · p. 4
2 GND
Ground connection. · p. 4
3 FLT
Active-low open-drain output, asserted during overcurrent or overtemperature conditions. · p. 4
4 EN/ EN
Enable input, logic high turns on power switch. · p. 4
5 IN
Input voltage and power-switch drain; connect a 0.1-uF or greater ceramic capacitor from IN to GND close to the IC. · p. 4

Open-source boards using it

18See all 18
  • 4 layers161.6 × 100 mmNubus to ztex, the printed circuit board in 3D

    Nubus to ztex

    MelkhiorVintageComputing/NuBusFPGA

    Stuff to put a FPGA in a NuBus Macintosh

    103 parts63
  • 4 layers99.7 × 83.8 mmSbus to ztex, the printed circuit board in 3D

    Sbus to ztex

    MelkhiorVintageComputing/SBusFPGA

    Stuff to put a FPGA in a SBus system (SPARCstation)

    64 parts54
  • 2 layers55 × 35 mmBaconbits, the printed circuit board in 3D

    Baconbits

    e-ale/BaconBitsCapeHW

    Design files for the Bacon Bits MiniCape for the PocketBeagle

    64 parts23
  • 2 layers50.8 × 22.9 mmHostess Feather, the printed circuit board in 3D

    Hostess Feather

    wntrblm/Hostess_FeatherWing

    Hostess is a FeatherWing that provides a USB host co-processor. The FeatherWing handles all USB Host related tasks, including enumeration and running the device drivers, and communicates with the primary processor over…

    33 parts16
  • 4 layers100 × 74 mmBeaglelogic standalone, the printed circuit board in 3D

    Beaglelogic standalone

    abhishek-kakkar/beaglelogic-standalone

    BeagleLogic implemented as a turnkey and standalone logic analyzer

    260 parts15
  • 6 layers119.8 × 96.8 mmTdt4295, the printed circuit board in 3D

    Tdt4295

    fredrikr79/TDT4295-datamaskinprosjekt

    a noita-like made with hardware acceleration via an FPGA, controlled by an MCU and implemented physically on a PCB

    158 parts3
  • 4 layers128 × 79 mmBMS, the printed circuit board in 3D

    BMS

    eChook/BMS-Comms-Board

    [PCB][KiCad] PCB Files for BMS Comms Master Board

    229 parts2
  • 4 layers70 × 100 mmNeural Edge, the printed circuit board in 3D

    Neural Edge

    rithylim/ESP32-P4-Neural-Edge-PCB

    140 parts1

Parts like it

8

Questions

Is there a KiCad symbol and footprint for the TPS2051CDBV?

Yes. The symbol is Power_Management:TPS2051CDBV and the footprint Package_TO_SOT_SMD:SOT-23-5, both drawn on this page. PCBKit places them on a board for you when you design with it.

What package is the TPS2051CDBV?

SOT-23-5, with 5 pins. Its footprint is drawn on this page.

Where is the TPS2051CDBV datasheet?

Texas Instruments publishes it: the Datasheet link on this page opens it.

Where can I order the TPS2051CDBV?

JLCPCB lists it as part C129581, with 15,916 in stock; the sellers' links on this page open their listings.

What can replace the TPS2051CDBV?

Parts like it in the library: the SY6280AAC by 矽力杰silergy, the AP2171WG by Diodes Incorporated, the TPS2051BDBV by Texas Instruments and the RT9742CGJ5 by RICHTEK. Check their datasheets: a part that fits the footprint may still differ in its ratings.

Which open-source boards use the TPS2051CDBV?

18 boards in 16 repositories on GitHub; the most starred are listed on this page, with their KiCad files.