Skip to the content
25

TCA8418RTW

Texas InstrumentsExtended

-40℃~+85℃ 1.65V~3.6V 18 1MHz I2C Input anti-jitter、Keyboard matrix scanning Interrupt Output Open-drain WQFN-24-EP(4x4) I/O Expanders ROHS

Part id
ti/TCA8418RTW
Category
I, O Expanders
Package
WQFN-24-EP(4x4)
Pins
25
In stock
30,639 at JLCPCB (C138713)
Used on
20 open-source boards

Overview

The TCA8418RTW is an i, O Expander made by Texas Instruments in a WQFN-24-EP(4x4) package with 25 pins. -40℃~+85℃ 1.65V~3.6V 18 1MHz I2C Input anti-jitter、Keyboard matrix scanning Interrupt Output Open-drain WQFN-24-EP(4x4) I/O Expanders ROHS.

PCBKit's library has its KiCad symbol (EasyEDA_Cloud:TCA8418RTWR, from EasyEDA) and its footprint (EasyEDA_Cloud:WQFN-24_L4.0-W4.0-P0.50-TL-EP2.5, from EasyEDA), ready for a KiCad board. 30,639 are in stock at JLCPCB (part C138713). 20 open-source boards in 18 repositories on GitHub use it.

Symbol

1ROW72ROW63ROW54ROW45ROW36ROW27ROW18ROW09COL010COL111COL212COL313COL414COL515COL616COL717COL818COL919GND20RESET#21VCC22SDA23SCL24INT#25EP
EasyEDA_Cloud:TCA8418RTWRFrom EasyEDA

Footprint

25
EasyEDA_Cloud:WQFN-24_L4.0-W4.0-P0.50-TL-EP2.5From EasyEDA

From the datasheet

14
Supply, least
1.65 V · VCC, recommended operating min · p. 4
Supply, most
3.6 V · VCC, recommended operating max · p. 4
Supply, absolute maximum
4.6 V · VCC, absolute max · p. 4
Works from
-40 °C · Operating free-air temperature min · p. 4
Works up to
85 °C · Operating free-air temperature max · p. 4
Takes working
153 µA · VCC supply current max, 1 key press, fSCL = 1 MHz, VCC = 3.6 V · p. 5
Takes at most
153 µA · VCC supply current max, 1 key press, fSCL = 1 MHz, VCC = 3.6 V · p. 5
Takes asleep
10 µA · VCC supply current max, fSCL = 0 kHz, oscillator OFF · p. 5
A pin gives at most
50 mA · P port and SDA continuous low output current absolute max · p. 4
A pin gives at most
25 mA · INT continuous low output current absolute max · p. 4
Junction to air (RTW (WQFN))
38.9 K/W · Junction-to-ambient thermal resistance · p. 4
Junction to case (RTW (WQFN))
40.6 K/W · Junction-to-case top thermal resistance · p. 4
Junction to board (RTW (WQFN))
17.2 K/W · Junction-to-board thermal resistance · p. 4
Data rate, most
1 Mbit/s · I2C Fast Mode Plus max · p. 6

What it is and has

11
Function
I2C controlled keypad scan IC with integrated ESD protection · p. 1
GPIO
18 GPIOs supporting up to 80 buttons · p. 1
Keypad
QWERTY keypad operation plus GPIO expansion · p. 1
I2C
1-MHz Fast Mode Plus · p. 1
FIFO
10 bytes, stores 10 key presses and releases · p. 1
Interrupt
Open-drain active-low output · p. 1
Debounce
Integrated debounce time of 50 μs · p. 1
Latch-up performance
Exceeds 200 mA per JESD 78, Class II · p. 1
ESD protection
2000-V Human Body Model (A114-A) · p. 1
ESD protection
1000-V Charged Device Model (C101) · p. 1
Package
WQFN (24), 4.00 mm × 4.00 mm · p. 1

Around it

22
res not specified
between RESET and VCC; Pull-up resistor if no active connection is used. · p. 3
res not specified
between SDA and VCC; Serial data bus pull-up resistor. · p. 3
res not specified
between SCL and VCC; Serial clock bus pull-up resistor. · p. 3
res not specified
between INT and VCC; Open-drain interrupt output pull-up resistor. · p. 3
res not specified
between ROW7 and VCC; Pull-up resistor if unused. · p. 3
res not specified
between ROW6 and VCC; Pull-up resistor if unused. · p. 3
res not specified
between ROW5 and VCC; Pull-up resistor if unused. · p. 3
res not specified
between ROW4 and VCC; Pull-up resistor if unused. · p. 3
res not specified
between ROW3 and VCC; Pull-up resistor if unused. · p. 3
res not specified
between ROW2 and VCC; Pull-up resistor if unused. · p. 3
res not specified
between ROW1 and VCC; Pull-up resistor if unused. · p. 3
res not specified
between ROW0 and VCC; Pull-up resistor if unused. · p. 3
res not specified
between COL0 and VCC; Pull-up resistor if unused. · p. 3
res not specified
between COL1 and VCC; Pull-up resistor if unused. · p. 3
res not specified
between COL2 and VCC; Pull-up resistor if unused. · p. 3
res not specified
between COL3 and VCC; Pull-up resistor if unused. · p. 3
res not specified
between COL4 and VCC; Pull-up resistor if unused. · p. 3
res not specified
between COL5 and VCC; Pull-up resistor if unused. · p. 3
res not specified
between COL6 and VCC; Pull-up resistor if unused. · p. 3
res not specified
between COL7 and VCC; Pull-up resistor if unused. · p. 3
res not specified
between COL8 and VCC; Pull-up resistor if unused. · p. 3
res not specified
between COL9 and VCC; Pull-up resistor if unused. · p. 3

Specifications

119
ParameterConditionsAs printedPage
Supply voltage range VCCOver operating free-air temperature rangemin -0.5 · max 4.6 V4
Input voltage range VIOver operating free-air temperature range; note (2)min -0.5 · max 4.6 V4
Voltage range applied to any output in the high-impedance or power-off state VOOver operating free-air temperature range; note (2)min -0.5 · max 4.6 V4
Output voltage range in the high or low state VOOver operating free-air temperature range; note (2)min -0.5 · max 4.6 V4
Input clamp current IIKVI < 0; maximum magnitude ±20 mAmax 20 mA4
Output clamp current IOKVO < 0; maximum magnitude ±20 mAmax 20 mA4
Continuous output Low current IOLP port, SDA; VO = 0 to VCCmax 50 mA4
Continuous output Low current IOLINT; VO = 0 to VCCmax 25 mA4
Continuous output High current IOHP port; VO = 0 to VCCmax 50 mA4
Storage temperature range Tstgmin -65 · max 150 °C4
Electrostatic discharge V(ESD)Human body model (HBM), per ANSI/ESDA/JEDEC JS-001, all pins; value ±2000 Vmax 2000 V4
Electrostatic discharge V(ESD)Charged device model (CDM), per JEDEC specification JESD22-C101, all pins; value ±1000 Vmax 1000 V4
Supply voltage VCCmin 1.65 · max 3.6 V4
High-level input voltage VIHSCL, SDA, ROW0–7, COL0–9, RESET; minimum 0.7 × VCCmax 3.6 V4
Low-level input voltage VILSCL, SDA, ROW0–7, COL0–9, RESET; maximum 0.3 × VCCmin -0.5 V4
High-level output current IOHROW0–7, COL0–9max 10 mA4
Low-level output current IOLROW0–7, COL0–9max 25 mA4
Operating free-air temperature TAmin -40 · max 85 °C4
Junction-to-ambient thermal resistance RθJATCA8418; RTW (WQFN), 24 PINStyp 38.9 °C/W4
Junction-to-case (top) thermal resistance RθJC(top)TCA8418; RTW (WQFN), 24 PINStyp 40.6 °C/W4
Junction-to-board thermal resistance RθJBTCA8418; RTW (WQFN), 24 PINStyp 17.2 °C/W4
Junction-to-top characterization parameter ψJTTCA8418; RTW (WQFN), 24 PINStyp 0.9 °C/W4
Junction-to-board characterization parameter ψJBTCA8418; RTW (WQFN), 24 PINStyp 17.2 °C/W4
Junction-to-case (bottom) thermal resistance RθJC(bot)TCA8418; RTW (WQFN), 24 PINStyp 6.6 °C/W4
Input diode clamp voltage VIKII = –18 mA; VCC = 1.65 V to 3.6 Vmin -1.2 V5
Power-on reset voltage, VCC rising VPORRVI = VCC or GND, IO = 0; VCC = 1.65 V to 3.6 Vmin 1.03 · max 1.43 V5
Power-on reset voltage, VCC falling VPORFVI = VCC or GND, IO = 0; VCC = 1.65 V to 3.6 Vmin 0.76 · max 1.15 V5
ROW0–7, COL0–9 high-level output voltage VOHIOH = –1 mA; VCC = 1.65 Vmin 1.25 V5
ROW0–7, COL0–9 high-level output voltage VOHIOH = –8 mA; VCC = 1.65 Vmin 1.2 V5
ROW0–7, COL0–9 high-level output voltage VOHIOH = –8 mA; VCC = 2.3 Vmin 1.8 V5
ROW0–7, COL0–9 high-level output voltage VOHIOH = –8 mA; VCC = 3 Vmin 2.6 V5
ROW0–7, COL0–9 high-level output voltage VOHIOH = –10 mA; VCC = 1.65 Vmin 1.1 V5
ROW0–7, COL0–9 high-level output voltage VOHIOH = –10 mA; VCC = 2.3 Vmin 1.7 V5
ROW0–7, COL0–9 high-level output voltage VOHIOH = –10 mA; VCC = 3 Vmin 2.5 V5
ROW0–7, COL0–9 low-level output voltage VOLIOL = 1 mA; VCC = 1.65 Vmax 0.4 V5
ROW0–7, COL0–9 low-level output voltage VOLIOL = 8 mA; VCC = 1.65 Vmax 0.45 V5
ROW0–7, COL0–9 low-level output voltage VOLIOL = 8 mA; VCC = 2.3 Vmax 0.25 V5
ROW0–7, COL0–9 low-level output voltage VOLIOL = 8 mA; VCC = 3 Vmax 0.25 V5
ROW0–7, COL0–9 low-level output voltage VOLIOL = 10 mA; VCC = 1.65 Vmax 0.6 V5
ROW0–7, COL0–9 low-level output voltage VOLIOL = 10 mA; VCC = 2.3 Vmax 0.3 V5
ROW0–7, COL0–9 low-level output voltage VOLIOL = 10 mA; VCC = 3 Vmax 0.25 V5
SDA IOLVOL = 0.4 V; VCC = 1.65 V to 3.6 Vmin 3 mA5
INT and CAD_INT IOLVOL = 0.4 V; VCC = 1.65 V to 3.6 Vmin 3 mA5
SCL, SDA, ROW0–7, COL0–9, RESET IIVI = VCCI or GND; VCC = 1.65 V to 3.6 Vmax 1 uA5
Internal pull-up resistor value RINTROW0–7, COL0–9typ 105 kΩ5
Supply current ICCVI on SDA, ROW0–7, COL0–9 = VCC or GND, IO = 0, I/O = inputs; fSCL = 0 kHz; oscillator OFF; VCC = 1.65 V to 3.6 Vmax 10 uA5
Supply current ICCVI on SDA, ROW0–7, COL0–9 = VCC or GND, IO = 0, I/O = inputs; fSCL = 0 kHz; oscillator ON; VCC = 1.65 V to 3.6 Vmax 18 uA5
Supply current ICCVI on SDA, ROW0–7, COL0–9 = VCC or GND, IO = 0, I/O = inputs; 1 key press; fSCL = 400 kHz; VCC = 1.65 Vmax 50 uA5
Supply current ICCVI on SDA, ROW0–7, COL0–9 = VCC or GND, IO = 0, I/O = inputs; 1 key press; fSCL = 400 kHz; VCC = 3.6 Vmax 90 uA5
Supply current ICCVI on SDA, ROW0–7, COL0–9 = VCC or GND, IO = 0, I/O = inputs; 1 key press; fSCL = 1 MHz; VCC = 3.6 Vmax 153 uA5
Supply current ICCVI on SDA, ROW0–7, COL0–9 = VCC or GND, IO = 0, I/O = inputs; GPI low (pull-up enable); one GPIO enabled; fSCL = 400 kHz; VCC = 1.65 V to 3.6 Vmax 55 uA5
Supply current ICCVI on SDA, ROW0–7, COL0–9 = VCC or GND, IO = 0, I/O = inputs; GPI low (pull-up enable); one GPIO enabled; fSCL = 1 MHz; VCC = 1.65 V to 3.6 Vmax 65 uA5
Supply current ICCVI on SDA, ROW0–7, COL0–9 = VCC or GND, IO = 0, I/O = inputs; GPI low (pull-up disable); fSCL = 400 kHz; VCC = 1.65 V to 3.6 Vmax 15 uA5
Supply current ICCVI on SDA, ROW0–7, COL0–9 = VCC or GND, IO = 0, I/O = inputs; GPI low (pull-up disable); fSCL = 1 MHz; VCC = 1.65 V to 3.6 Vmax 24 uA5
Supply current ICCVI on SDA, ROW0–7, COL0–9 = VCC or GND, IO = 0, I/O = inputs; 1 GPO active; fSCL = 400 kHz; VCC = 1.65 V to 3.6 Vmax 55 uA5
Supply current ICCVI on SDA, ROW0–7, COL0–9 = VCC or GND, IO = 0, I/O = inputs; 1 GPO active; fSCL = 1 MHz; VCC = 1.65 V to 3.6 Vmax 65 uA5
SCL CIVI = VCCI or GND; VCC = 1.65 V to 3.6 Vtyp 6 · max 8 pF5
SDA CioVIO = VCC or GND; VCC = 1.65 V to 3.6 Vtyp 10 · max 12.5 pF5
ROW0–7, COL0–9 CioVIO = VCC or GND; VCC = 1.65 V to 3.6 Vtyp 5 · max 6 pF5
I2C clock frequency fsclSTANDARD MODE I2C BUSmin 0 · max 100 kHz6
I2C clock frequency fsclFAST MODE I2C BUSmin 0 · max 400 kHz6
I2C clock frequency fsclFAST MODE PLUS (FM+) I2C BUSmin 0 · max 1000 kHz6
I2C clock high time tschSTANDARD MODE I2C BUSmin 4 us6
I2C clock high time tschFAST MODE I2C BUSmin 0.6 us6
I2C clock high time tschFAST MODE PLUS (FM+) I2C BUSmin 0.26 us6
I2C clock low time tsclSTANDARD MODE I2C BUSmin 4.7 us6
I2C clock low time tsclFAST MODE I2C BUSmin 1.3 us6
I2C clock low time tsclFAST MODE PLUS (FM+) I2C BUSmin 0.5 us6
I2C spike time tspSTANDARD MODE I2C BUSmax 50 ns6
I2C spike time tspFAST MODE I2C BUSmax 50 ns6
I2C spike time tspFAST MODE PLUS (FM+) I2C BUSmax 50 ns6
I2C serial data setup time tsdsSTANDARD MODE I2C BUSmin 250 ns6
I2C serial data setup time tsdsFAST MODE I2C BUSmin 100 ns6
I2C serial data setup time tsdsFAST MODE PLUS (FM+) I2C BUSmin 50 ns6
I2C serial data hold time tsdhSTANDARD MODE I2C BUSmin 0 ns6
I2C serial data hold time tsdhFAST MODE I2C BUSmin 0 ns6
I2C serial data hold time tsdhFAST MODE PLUS (FM+) I2C BUSmin 0 ns6
I2C input rise time ticrSTANDARD MODE I2C BUSmax 1000 ns6
I2C input rise time ticrFAST MODE I2C BUS; minimum 20 + 0.1Cb; Cb = total capacitance of one bus line in pFmax 300 ns6
I2C input rise time ticrFAST MODE PLUS (FM+) I2C BUSmax 120 ns6
I2C input fall time ticfSTANDARD MODE I2C BUSmax 300 ns6
I2C input fall time ticfFAST MODE I2C BUS; minimum 20 + 0.1Cb; Cb = total capacitance of one bus line in pFmax 300 ns6
I2C input fall time ticfFAST MODE PLUS (FM+) I2C BUSmax 120 ns6
I2C output fall time; 10 pF to 400 pF bus tocfSTANDARD MODE I2C BUSmax 300 us6
I2C output fall time; 10 pF to 400 pF bus tocfFAST MODE I2C BUS; minimum 20 + 0.1Cb; Cb = total capacitance of one bus line in pFmax 300 us6
I2C output fall time; 10 pF to 400 pF bus tocfFAST MODE PLUS (FM+) I2C BUSmax 120 us6
I2C bus free time between Stop and Start tbufSTANDARD MODE I2C BUSmin 4.7 us6
I2C bus free time between Stop and Start tbufFAST MODE I2C BUSmin 1.3 us6
I2C bus free time between Stop and Start tbufFAST MODE PLUS (FM+) I2C BUSmin 0.5 us6
I2C Start or repeater Start condition setup time tstsSTANDARD MODE I2C BUSmin 4.7 us6
I2C Start or repeater Start condition setup time tstsFAST MODE I2C BUSmin 0.6 us6
I2C Start or repeater Start condition setup time tstsFAST MODE PLUS (FM+) I2C BUSmin 0.26 us6
I2C Start or repeater Start condition hold time tsthSTANDARD MODE I2C BUSmin 4 us6
I2C Start or repeater Start condition hold time tsthFAST MODE I2C BUSmin 0.6 us6
I2C Start or repeater Start condition hold time tsthFAST MODE PLUS (FM+) I2C BUSmin 0.26 us6
I2C Stop condition setup time tspsSTANDARD MODE I2C BUSmin 4 us6
I2C Stop condition setup time tspsFAST MODE I2C BUSmin 0.6 us6
I2C Stop condition setup time tspsFAST MODE PLUS (FM+) I2C BUSmin 0.26 us6
Valid data time; SCL low to SDA output valid tvd(data)STANDARD MODE I2C BUSmax 1 us6
Valid data time; SCL low to SDA output valid tvd(data)FAST MODE I2C BUSmax 0.9 us6
Valid data time; SCL low to SDA output valid tvd(data)FAST MODE PLUS (FM+) I2C BUSmax 0.45 us6
Valid data time of ACK condition; ACK signal from SCL low to SDA (out) low tvd(ack)STANDARD MODE I2C BUSmax 1 us6
Valid data time of ACK condition; ACK signal from SCL low to SDA (out) low tvd(ack)FAST MODE I2C BUSmax 0.9 us6
Valid data time of ACK condition; ACK signal from SCL low to SDA (out) low tvd(ack)FAST MODE PLUS (FM+) I2C BUSmax 0.45 us6
Reset pulse duration tWSTANDARD MODE, FAST MODE, FAST MODE PLUS (FM+) I2C BUS; note (1)min 120 us6
Reset recovery time tRECSTANDARD MODE, FAST MODE, FAST MODE PLUS (FM+) I2C BUS; note (1)min 120 us6
Time to reset tRESETSTANDARD MODE, FAST MODE, FAST MODE PLUS (FM+) I2C BUS; note (1)min 120 us6
Interrupt valid time tIVKey event or Key unlock or Overflow; ROW0–7, COL0–9 to INT; STANDARD MODE, FAST MODE, FAST MODE PLUS (FM+) I2C BUSmin 20 · max 60 us7
Interrupt valid time tIVGPI_INT with Debounce_DIS_Low; ROW0–7, COL0–9 to INT; STANDARD MODE, FAST MODE, FAST MODE PLUS (FM+) I2C BUSmin 40 · max 120 us7
Interrupt valid time tIVGPI_INT with Debounce_DIS_High; ROW0–7, COL0–9 to INT; STANDARD MODE, FAST MODE, FAST MODE PLUS (FM+) I2C BUSmin 10 · max 30 us7
Interrupt reset delay time tIRSCL to INT; STANDARD MODE, FAST MODE, FAST MODE PLUS (FM+) I2C BUSmax 200 ns7
Output data valid tPVSCL to ROW0–7, COL0–9; STANDARD MODE, FAST MODE, FAST MODE PLUS (FM+) I2C BUSmax 400 ns7
Input data setup time tPSP port to SCL; STANDARD MODE, FAST MODE, FAST MODE PLUS (FM+) I2C BUSmin 0 ns7
Input data hold time tPHP port to SCL; STANDARD MODE, FAST MODE, FAST MODE PLUS (FM+) I2C BUSmin 300 ns7
Key press to detection delaySTANDARD MODE, FAST MODE, FAST MODE PLUS (FM+) I2C BUSmax 25 us7
Key release to detection delaySTANDARD MODE, FAST MODE, FAST MODE PLUS (FM+) I2C BUSmax 25 us7
Keypad unlock timerSTANDARD MODE, FAST MODE, FAST MODE PLUS (FM+) I2C BUSmax 7 s7
Keypad interrupt mask timerSTANDARD MODE, FAST MODE, FAST MODE PLUS (FM+) I2C BUSmax 31 s7
DebounceSTANDARD MODE, FAST MODE, FAST MODE PLUS (FM+) I2C BUSmax 60 ms7

Pins, by the datasheet

24
1 ROW7
GPIO or row 7 in keypad matrix; if unused, connect to VCC through a pull-up resistor. · p. 3
2 ROW6
GPIO or row 6 in keypad matrix; if unused, connect to VCC through a pull-up resistor. · p. 3
3 ROW5
GPIO or row 5 in keypad matrix; if unused, connect to VCC through a pull-up resistor. · p. 3
4 ROW4
GPIO or row 4 in keypad matrix; if unused, connect to VCC through a pull-up resistor. · p. 3
5 ROW3
GPIO or row 3 in keypad matrix; if unused, connect to VCC through a pull-up resistor. · p. 3
6 ROW2
GPIO or row 2 in keypad matrix; if unused, connect to VCC through a pull-up resistor. · p. 3
7 ROW1
GPIO or row 1 in keypad matrix; if unused, connect to VCC through a pull-up resistor. · p. 3
8 ROW0
GPIO or row 0 in keypad matrix; if unused, connect to VCC through a pull-up resistor. · p. 3
9 COL0
GPIO or column 0 in keypad matrix; if unused, connect to VCC through a pull-up resistor. · p. 3
10 COL1
GPIO or column 1 in keypad matrix; if unused, connect to VCC through a pull-up resistor. · p. 3
11 COL2
GPIO or column 2 in keypad matrix; if unused, connect to VCC through a pull-up resistor. · p. 3
12 COL3
GPIO or column 3 in keypad matrix; if unused, connect to VCC through a pull-up resistor. · p. 3
13 COL4
GPIO or column 4 in keypad matrix; if unused, connect to VCC through a pull-up resistor. · p. 3
14 COL5
GPIO or column 5 in keypad matrix; if unused, connect to VCC through a pull-up resistor. · p. 3
15 COL6
GPIO or column 6 in keypad matrix; if unused, connect to VCC through a pull-up resistor. · p. 3
16 COL7
GPIO or column 7 in keypad matrix; if unused, connect to VCC through a pull-up resistor. · p. 3
17 COL8
GPIO or column 8 in keypad matrix; if unused, connect to VCC through a pull-up resistor. · p. 3
18 COL9
GPIO or column 9 in keypad matrix; if unused, connect to VCC through a pull-up resistor. · p. 3
19 GND
Ground. · p. 3
20 RESET
Active-low reset input; connect to VCC through a pull-up resistor if no active connection is used. · p. 3
21 VCC
Supply voltage of 1.65 V to 3.6 V. · p. 3
22 SDA
Serial data bus; connect to VCC through a pull-up resistor. · p. 3
23 SCL
Serial clock bus; connect to VCC through a pull-up resistor. · p. 3
24 INT
Active-low interrupt output with open drain structure; connect to VCC through a pull-up resistor. · p. 3

Open-source boards using it

20See all 20
  • 2 layers192.4 × 50 mmOmote, the printed circuit board in 3D

    Omote

    OMOTE-Community/OMOTE-Hardware

    Open Source Remote - Hardware

    187 parts157GPL-3.0
  • 2 layers97.2 × 81.3 mmRadiotxt, the printed circuit board in 3D

    Radiotxt

    AnthonyDiGirolamo/i2c-thumb-keyboard

    Handheld tactile switch keyboard using the TCA8418.

    85 parts30MIT
  • 2 layers149.9 × 167.6 mmCollins FMS-3000, the printed circuit board in 3D

    Collins FMS-3000

    neilenns/Collins-FMS-3000

    PCB for a replica Collins FMS-3000 to use with MobiFlight

    126 parts6MIT
  • 2 layers60 × 55 mm3x4 keyboard, the printed circuit board in 3D

    3x4 keyboard

    Tomas-Kuchta-FPV/Travel-Buddy

    Pocketable, smart and sleek Meshtastic node. With keyboard, Eink screen, GPS and all day baterry life thanks to it's Solar panel and nRF52 in Wio tracker L1.

    33 parts6CERN-OHL-W-2.0
  • 2 layers88 × 90.3 mmKeebDeckHexpansion, the printed circuit board in 3D

    KeebDeckHexpansion

    davedarko/KeebDeckHexpansion

    A Keyboard Hexpansion using the solder.party KeebDeck Keyboard

    39 parts5MIT
  • 2 layers86 × 165 mmCalculator, the printed circuit board in 3D

    Calculator

    Ethan-Poag/Flight-Data-Computer

    An easy to build open source alternative to the ASA CX-3 aviation data computer.

    131 parts3GPL-3.0
  • 2 layers99.1 × 59.7 mmKeypad 47, the printed circuit board in 3D

    Keypad 47

    soupie-62/Keypad

    Pmod compatible I2C keyboard

    109 parts3GPL-3.0
  • 2 layers88 × 90.3 mmKeebdexpansion, the printed circuit board in 3D

    Keebdexpansion

    emfcamp/Keebdexpansion

    A keyboard hexpansion for the Tildagon badge using the solder.party KeebDeck Keyboard. Software for the hexpansion is provided by @sodoku.

    30 parts2MIT

Parts like it

8

Questions

Is there a KiCad symbol and footprint for the TCA8418RTW?

Yes. The symbol is EasyEDA_Cloud:TCA8418RTWR and the footprint EasyEDA_Cloud:WQFN-24_L4.0-W4.0-P0.50-TL-EP2.5, both drawn on this page. PCBKit places them on a board for you when you design with it.

What package is the TCA8418RTW?

WQFN-24-EP(4x4), with 25 pins. Its footprint is drawn on this page.

Where is the TCA8418RTW datasheet?

Texas Instruments publishes it: the Datasheet link on this page opens it.

Where can I order the TCA8418RTW?

JLCPCB lists it as part C138713, with 30,639 in stock; the sellers' links on this page open their listings.

What can replace the TCA8418RTW?

Parts like it in the library: the TCAL6416RTW by Texas Instruments, the CH422G by WCH (Nanjing Qinheng Microelectronics), the TCA9536DGKR by Texas Instruments and the CH423S by WCH (Nanjing Qinheng Microelectronics). Check their datasheets: a part that fits the footprint may still differ in its ratings.

Which open-source boards use the TCA8418RTW?

20 boards in 18 repositories on GitHub; the most starred are listed on this page, with their KiCad files.