Skip to the content
PCBKitNew board
OPA192ID on a board, in 3D

OPA192ID

Texas Instruments

-18V~-2.25V、2.25V~18V -40℃~+125℃ 1 10MHz 140dB 1mA 200nV/℃ 20V/us 2pA 4.5V~36V 5.5nV/√Hz@1kHz 5pA 5uV 65mA Rail-to-Rail Input, Rail-to-Rail Output SOIC-8 Precision Op Amps ROHS

Extended
DatasheetJLCPCBLCSCti/OPA192ID
Category
Precision Op Amps
Package
SOIC-8
Pins
8

Overview

The OPA192ID is a precision Op Amp made by Texas Instruments in a SOIC-8 package with 8 pins. -18V~-2.25V、2.25V~18V -40℃~+125℃ 1 10MHz 140dB 1mA 200nV/℃ 20V/us 2pA 4.5V~36V 5.5nV/√Hz@1kHz 5pA 5uV 65mA Rail-to-Rail Input, Rail-to-Rail Output SOIC-8 Precision Op Amps ROHS.

PCBKit's library has its KiCad symbol (EasyEDA_Cloud:OPA388IDR-TP, from EasyEDA) and its footprint (Package_SO:SOIC-8_3.9x4.9mm_P1.27mm, from KiCad's library), ready for a KiCad board. 2,196 are in stock at JLCPCB (part C2861286). 11 open-source boards in 10 repositories on GitHub use it.

Symbol

NC1-IN2+IN3V-4NC5OUT6V+7NC8
EasyEDA_Cloud:OPA388IDR-TPFrom EasyEDA

Footprint

12345678
Package_SO:SOIC-8_3.9x4.9mm_P1.27mmFrom KiCad's library

From the datasheet

10
Supply, least
4.5 V · V+ – V–, recommended operating min · p. 6
Supply, most
36 V · V+ – V–, recommended operating max · p. 6
Supply, absolute maximum
40 V · V+ – V–, single-supply absolute max · p. 6
Works from
-40 °C · rated operating ambient min · p. 6
Works up to
125 °C · rated operating ambient max · p. 6
Junction, hottest
150 °C · junction absolute max · p. 6
Takes working
1 mA · quiescent current typical, IO = 0 A, VS = 8 to 36 V · p. 9
Junction to air (D (SOIC))
115.8 K/W · junction to ambient · p. 7
Junction to case (D (SOIC))
60.1 K/W · junction to case top · p. 7
Junction to board (D (SOIC))
56.4 K/W · junction to board · p. 7

What it is and has

13
Input/output
Rail-to-rail · p. 1
Gain bandwidth product
10MHz · p. 1
Slew rate
20V/µs · p. 1
Input offset voltage
±5µV · p. 1
Input offset voltage drift
±0.2µV/°C · p. 1
Input bias current
±5pA · p. 1
Input noise
5.5nV/√Hz at 1kHz · p. 1
Common-mode rejection
140dB · p. 1
Input filtering
EMI/RFI · p. 1
Differential input voltage range
To the supply rails · p. 1
Capacitive load drive
1nF · p. 1
Protection
Internal phase-reversal protection · p. 26
Protection
Thermal protection disables output drive above 140°C · p. 26

Specifications

89
ParameterConditionsAs printedPage
电源电压，VS = (V+) – (V–) VS单通道电源max 40 V6
信号输入引脚 电流±10 mAmin -10 · max 10 mA6
工作 温度范围min -55 · max 150 °C6
工作 结温max 150 °C6
储存温度，Tstg Tstgmin -65 · max 150 °C6
静电放电 V(ESD)人体放电模型 (HBM)，符合 ANSI/ESDA/JEDEC JS-001；±4000 Vmin -4000 · max 4000 V6
静电放电 V(ESD)OPA192；充电器件模型 (CDM)，符合 JEDEC 规范 JESD22-C101；±1000 Vmin -1000 · max 1000 V6
电源电压，VS = (V+) – (V–) VS单电源；双电源范围 ±2.25 V 至 ±18 Vmin 4.5 · max 36 V6
额定温度范围min -40 · max 125 °C6
结至环境热阻 RθJAOPA192；D (SOIC)，8 引脚typ 115.8 °C/W7
结至芯片外壳（顶部）热阻 RθJC(top)OPA192；D (SOIC)，8 引脚typ 60.1 °C/W7
结至电路板热阻 RθJBOPA192；D (SOIC)，8 引脚typ 56.4 °C/W7
结至顶部的特征参数 ψJTOPA192；D (SOIC)，8 引脚typ 12.8 °C/W7
结至电路板的特征参数 ψJBOPA192；D (SOIC)，8 引脚typ 55.9 °C/W7
输入失调电压 VOSTA = +25°C；数值为 ±typ 5 · max 25 uV8
输入失调电压 VOSTA = 0°C 至 85°C；数值为 ±typ 8 · max 50 uV8
输入失调电压 VOSTA = -40°C 至 +125°C；数值为 ±typ 10 · max 75 uV8
输入失调电压 VOSVCM = (V+) – 1.5V；TA = +25°C；数值为 ±typ 10 · max 40 uV8
输入失调电压 VOSVCM = (V+) – 1.5V；TA = 0°C 至 85°C；数值为 ±typ 25 · max 150 uV8
输入失调电压 VOSVCM = (V+) – 1.5V；TA = -40°C 至 +125°C；数值为 ±typ 50 · max 250 uV8
输入失调电压漂移 dVOS/dT仅 D 封装；TA = 0°C 至 85°C；数值为 ±typ 0.1 · max 0.5 uV/°C8
输入失调电压漂移 dVOS/dT仅 D 封装；TA = -40°C 至 +125°C；数值为 ±typ 0.15 · max 0.8 uV/°C8
电源抑制比 PSRRTA = -40°C 至 +125°C；数值为 ±typ 0.3 · max 1 uV/V8
输入偏置电流 IBTA = +25°C；数值为 ±typ 5 · max 20 pA8
输入偏置电流 IBTA=-40°C 至 +125°C；数值为 ±max 5 nA8
输入偏移电流 IOSTA = +25°C；数值为 ±typ 2 · max 20 pA8
输入偏移电流 IOSTA=-40°C 至 +125°C；数值为 ±max 2 nA8
输入电压噪声 En(V-)-0.1V<VCM<(V+)-3V；f = 0.1Hz 至 10Hztyp 1.3 uVPP8
输入电压噪声 En(V+) – 1.5V < VCM < (V+) + 0.1V；f = 0.1Hz 至 10Hztyp 4 uVPP8
输入电压噪声密度 en(V-)-0.1V<VCM<(V+)-3V；f = 100Hztyp 10.5 nV/√Hz8
输入电压噪声密度 en(V-)-0.1V<VCM<(V+)-3V；f=1kHztyp 5.5 nV/√Hz8
输入电压噪声密度 en(V+) – 1.5V < VCM < (V+) + 0.1V；f = 100Hztyp 32 nV/√Hz8
输入电压噪声密度 en(V+) – 1.5V < VCM < (V+) + 0.1V；f = 1kHztyp 12.5 nV/√Hz8
输入电流噪声密度 inf=1kHztyp 1.5 fA/√Hz8
共模抑制比 CMRR(V-)-0.1V<VCM<(V+)-3V；TA = +25°Cmin 120 · typ 140 dB8
共模抑制比 CMRR(V-)-0.1V<VCM<(V+)-3V；TA = -40°C 至 +125°Cmin 114 · typ 126 dB8
共模抑制比 CMRR(V+) – 1.5V < VCM < (V+)；TA = +25°Cmin 100 · typ 120 dB8
共模抑制比 CMRR(V+) – 1.5V < VCM < (V+)；TA = -40°C 至 +125°Cmin 86 · typ 100 dB8
开环电压增益 AOL(V–) + 0.6V < VO < (V+) – 0.6V，RLOAD = 2kΩ；TA = +25°Cmin 120 · typ 134 dB8
开环电压增益 AOL(V–) + 0.6V < VO < (V+) – 0.6V，RLOAD = 2kΩ；TA = -40°C 至 +125°Cmin 114 · typ 126 dB8
开环电压增益 AOL(V–) + 0.3V < VO < (V+) – 0.3V，RLOAD = 10kΩ；TA = +25°Cmin 126 · typ 140 dB8
开环电压增益 AOL(V–) + 0.3V < VO < (V+) – 0.3V，RLOAD = 10kΩ；TA = -40°C 至 +125°Cmin 120 · typ 134 dB8
单位带宽增益积 GBWtyp 10 MHz9
压摆率 SRG = 1，10V阶跃typ 20 V/us9
稳定时间 ts达 0.01%；V S = ±18V，G = 1，10V 阶跃typ 1.4 us9
稳定时间 ts达 0.01%；V S = ±18V，G = 1，5V 阶跃typ 0.9 us9
稳定时间 ts达 0.001%；V S = ±18V，G = 1，10V 阶跃typ 2.1 us9
稳定时间 ts达 0.001%；V S = ±18V，G = 1，5V 阶跃typ 1.8 us9
过载恢复时间 tORVIN × G = VStyp 200 ns9
总谐波失真 + 噪声 THD+NG = 1，f = 1kHz，VO = 3.5VRMStyp 0.00008 %9
电压输出摆幅到 VO正电源轨；无负载typ 5 · max 15 mV9
电压输出摆幅到 VO正电源轨；RLOAD = 10kΩtyp 95 · max 110 mV9
电压输出摆幅到 VO正电源轨；RLOAD = 2kΩtyp 430 · max 500 mV9
电压输出摆幅到 VO负电源轨；无负载typ 5 · max 15 mV9
电压输出摆幅到 VO负电源轨；RLOAD = 10kΩtyp 95 · max 110 mV9
电压输出摆幅到 VO负电源轨；RLOAD = 2kΩtyp 430 · max 500 mV9
短路电流 ISC典型值 ±65 mAtyp 65 mA9
开环输出阻抗 ZOf=1MHz，IO = 0A，请参阅图 31typ 375 Ω9
每个放大器的静态电流 IQIO = 0A；TA = +25°Ctyp 1 · max 1.2 mA9
每个放大器的静态电流 IQTA = –40°C 至 +125°C，IO = 0Amax 1.5 mA9
过热保护 (1)typ 140 °C9
输入失调电压 VOSVCM = (V+) – 3V；TA = +25°C；数值为 ±typ 5 · max 25 uV10
输入失调电压 VOSVCM = (V+) – 3V；TA = 0°C 至 85°C；数值为 ±typ 8 · max 50 uV10
输入失调电压 VOSVCM = (V+) – 3V；TA = -40°C 至 +125°C；数值为 ±typ 10 · max 75 uV10
输入失调电压 VOSVCM = (V+) – 1.5V；TA = 0°C 至 85°C；数值为 ±typ 25 · max 150 uV10
输入失调电压漂移 dVOS/dTVCM = (V+) – 3V；仅有D封装；TA = 0°C 至 85°C；数值为 ±typ 0.1 · max 0.5 uV/°C10
输入失调电压漂移 dVOS/dTVCM = (V+) – 3V；仅有D封装；TA = -40°C 至 +125°C；数值为 ±typ 0.15 · max 0.8 uV/°C10
输入失调电压漂移 dVOS/dTVCM = (V+) – 1.5V，TA = –40°C 至 +125°C；数值为 ±typ 0.5 · max 3 uV/°C10
电源抑制比 PSRRTA = –40°C 至 +125°C，VCM = VS / 2 – 0.75V；典型值 ±1typ 1 uV/V10
输入电压噪声 En(V–) – 0.1V < VCM < (V+) – 3V，f = 0.1Hz 至 10Hztyp 1.3 uVPP10
输入电压噪声 En(V+) – 1.5V < VCM < (V+) + 0.1V，f = 0.1Hz 至 10Hztyp 4 uVPP10
共模抑制比 CMRR(V–) – 0.1V < VCM < (V+) – 3V；TA = +25°Cmin 94 · typ 110 dB10
共模抑制比 CMRR(V–) – 0.1V < VCM < (V+) – 3V；TA = -40°C 至 +125°Cmin 90 · typ 104 dB10
共模抑制比 CMRR(V+) – 1.5V < VCM < (V+)；TA = -40°C 至 +125°Cmin 84 · typ 100 dB10
开环电压增益 AOL(V–) + 0.6V < VO < (V+) – 0.6V，RLOAD = 2kΩ；TA = +25°Cmin 110 · typ 120 dB10
开环电压增益 AOL(V–) + 0.6V < VO < (V+) – 0.6V，RLOAD = 2kΩ；TA = -40°C 至 +125°Cmin 100 · typ 114 dB10
开环电压增益 AOL(V–) + 0.3V < VO < (V+) – 0.3V，RLOAD = 10kΩ；TA = +25°Cmin 110 · typ 126 dB10
开环电压增益 AOL(V–) + 0.3V < VO < (V+) – 0.3V，RLOAD = 10kΩ；TA = -40°C 至 +125°Cmin 110 · typ 120 dB10
稳定时间 ts达 0.01%；VS = ±3V，G = 1，5V 阶跃typ 1 us11
过载恢复时间 tORVIN× G = VStyp 200 ns11
电源轨的电压输出摆幅 VO正电源轨；无负载typ 5 · max 15 mV11
电源轨的电压输出摆幅 VO正电源轨；RLOAD = 10kΩtyp 95 · max 110 mV11
电源轨的电压输出摆幅 VO正电源轨；RLOAD = 2kΩtyp 430 · max 500 mV11
电源轨的电压输出摆幅 VO负电源轨；无负载typ 5 · max 15 mV11
电源轨的电压输出摆幅 VO负电源轨；RLOAD = 10kΩtyp 95 · max 110 mV11
电源轨的电压输出摆幅 VO负电源轨；RLOAD = 2kΩtyp 430 · max 500 mV11
开环输出阻抗 ZOf=1MHz，IO = 0A，请参阅 图 31typ 375 Ω11
每个放大器的静态电流 IQIO = 0A；TA = +25°Ctyp 1 · max 1.2 mA11
每个放大器的静态电流 IQIO = 0A；TA = -40°C 至 +125°Cmax 1.5 mA11

Ordering codes, by the datasheet

6
OPA192ID
SOIC, D, 8 pins · Package quantity 75; operating temperature -40 to 125°C · p. 39
OPA192IDR
SOIC, D, 8 pins · Package quantity 2500; operating temperature -40 to 125°C · p. 39
OPA192IDBVR
SOT-23, DBV, 5 pins · Package quantity 3000; operating temperature -40 to 125°C · p. 39
OPA192IDBVT
SOT-23, DBV, 5 pins · Package quantity 250; operating temperature -40 to 125°C · p. 39
OPA192IDGKR
VSSOP, DGK, 8 pins · Package quantity 2500; operating temperature -40 to 125°C · p. 39
OPA192IDGKT
VSSOP, DGK, 8 pins · Package quantity 250; operating temperature -40 to 125°C · p. 39

Parameters

23
Common Mode Rejection Ratio(CMRR)
140dB
Current - Supply
1mA
Dual Supply
2.25V~18V
Features
Reverse-phase input protection
Gain Bandwidth Product
10MHz
Ib - Input Bias Current
5pA
Input Offset Current(Ios)
2pA
Input Offset Voltage Drift(Vos TC)
200nV/℃
Input Voltage Noise Density
5.5nV/√Hz@1kHz
Junction Temperature(Max)
150℃
Number of Channels
Single-channel
Operating Temperature
-40℃~+125℃
Output Current
65mA
Quiescent Current(Iq)
1mA
Rail to Rail
Rail-to-Rail Input, Rail-to-Rail Output
Single Supply
4.5V~36V
Slew Rate
20V/us
Thermal Resistance(Junction to Ambient)
115.8℃/W
Thermal Resistance(Junction to Board)
56.4℃/W
Thermal Resistance(Junction to Case)
60.1℃/W
Voltage - Supply
4.5V~36V
Voltage - Supply(Absolute Max)
40V
Vos - Input Offset Voltage
5uV

Order codes

2

Pinout

8
The pins of the OPA192ID
PinNameType
1NCUnspecified
2-INUnspecified
3+INUnspecified
4V-Unspecified
5NCUnspecified
6OUTUnspecified
7V+Unspecified
8NCUnspecified

Open-source boards using it

All 11
  • 4 layers60 × 81 mmMYSTAT, the printed circuit board in 3D

    MYSTAT

    matthew-yates/MYSTAT

    Open source potentiostat/galvanostat hardware design files and required software.

    93 parts9GPL-3.0
  • 4 layers92.5 × 147.5 mmADC, the printed circuit board in 3D

    ADC

    TheSilentDefender/ADC_Board_Aramaki_Lab

    267 parts2CERN-OHL-W-2.0
  • 4 layers130.8 × 58.9 mmAps radar, the printed circuit board in 3D

    Aps radar

    jason-merlo/AP-S-2020-Radar-Board

    362 parts1
  • 2 layers80 × 100 mmFlt06, the printed circuit board in 3D

    Flt06

    flukso/flt06

    PCB for testing the Fluksometer

    96 partsMIT
  • 6 layers73 × 100 mmETH3CADC1, the printed circuit board in 3D

    ETH3CADC1

    koson/ETH3CDAQ1

    407 parts
  • 2 layers36 × 20 mmBioamplifier pcb, the printed circuit board in 3D

    Bioamplifier pcb

    YagodkinaAA/bioamplifier-pcb

    KiCad PCB project — Bioamplifier

    12 parts
  • 2 layers196.4 × 195.1 mmMotherboard, the printed circuit board in 3D

    Motherboard

    ParadigmHyperloop/electrical

    All schematics and layouts in KiCad, plus some simulations

    291 parts11
  • 6 layers175 × 150 mmSINGLE BOARD, the printed circuit board in 3D

    SINGLE BOARD

    k16shikano/r2r-dac

    16ビットR-2RラダーによるDAコンバーターの設計

    357 parts

Show this part on your page

A live frame, for any web page
<iframe src="https://pcbkit.io/embed/parts/ti/OPA192ID" title="OPA192ID in PCBKit" width="100%" height="480" style="border:0;border-radius:12px" allow="fullscreen" loading="lazy"></iframe>
A picture
<img src="https://pcbkit.io/embed/parts/ti/OPA192ID.jpg" alt="OPA192ID" width="1200" height="900">
A picture that opens the part, for a README
[![OPA192ID](https://pcbkit.io/embed/parts/ti/OPA192ID.jpg?size=s)](https://pcbkit.io/parts/ti/OPA192ID)

Questions

Is there a KiCad symbol and footprint for the OPA192ID?

Yes. The symbol is EasyEDA_Cloud:OPA388IDR-TP and the footprint Package_SO:SOIC-8_3.9x4.9mm_P1.27mm, both drawn on this page. PCBKit places them on a board for you when you design with it.

What package is the OPA192ID?

SOIC-8, with 8 pins. Its footprint is drawn on this page.

Where is the OPA192ID datasheet?

Texas Instruments publishes it: the Datasheet link on this page opens it.

Where can I order the OPA192ID?

JLCPCB lists it as part C2861286, with 2,196 in stock; the sellers' links on this page open their listings.

What can replace the OPA192ID?

Parts like it in the library: the GS8552-SR by Gainsil, the OPA2192ID by Texas Instruments, the OPA197ID by Texas Instruments and the OPA189ID by Texas Instruments. Check their datasheets: a part that fits the footprint may still differ in its ratings.

Which open-source boards use the OPA192ID?

11 boards in 10 repositories on GitHub; the most starred are listed on this page, with their KiCad files.

Parts like it

8