Skip to the content
123456

INA199A1DCK

Texas InstrumentsExtended

-300mV~26V -40℃~+105℃ 0.4V/us 0.5uV/℃ 1 120dB 14kHz 2.7V~26V 25nV/√Hz@1kHz 28uA 50V/V 5uV 65uA High-side detection、Low-side detection、Bidirectional detection、Zero drift / auto-zero、Analog output interface、Input filter、Built-in comparator ±26V SOT-363(SC-70-6) Current Sense Amplifiers ROHS

Part id
ti/INA199A1DCK
Category
Current Sense Amplifiers
Package
SC-70-6
Pins
6
In stock
66,309 at JLCPCB (C59135)
Used on
5 open-source boards

Overview

The INA199A1DCK is a current Sense Amplifier made by Texas Instruments in a SC-70-6 package with 6 pins. -300mV~26V -40℃~+105℃ 0.4V/us 0.5uV/℃ 1 120dB 14kHz 2.7V~26V 25nV/√Hz@1kHz 28uA 50V/V 5uV 65uA High-side detection、Low-side detection、Bidirectional detection、Zero drift / auto-zero、Analog output interface、Input filter、Built-in comparator ±26V SOT-363(SC-70-6) Current Sense Amplifiers ROHS.

PCBKit's library has its KiCad symbol (Amplifier_Current:INA199xxDCK, from KiCad's library) and its footprint (Package_TO_SOT_SMD:SOT-363_SC-70-6, from KiCad's library), ready for a KiCad board. 66,309 are in stock at JLCPCB (part C59135). 5 open-source boards in 3 repositories on GitHub use it.

Symbol

1REF2GND3V+4+5-6
Amplifier_Current:INA199xxDCKFrom KiCad's library

Footprint

123456
Package_TO_SOT_SMD:SOT-363_SC-70-6From KiCad's library

From the datasheet

14
Supply, least
2.7 V · V+, minimum operating voltage at –40°C to 125°C · p. 6
Supply, most
26 V · V+, maximum operating voltage at –40°C to 125°C · p. 6
Supply, least
2.5 V · V+, minimum operating voltage at –20°C to 85°C · p. 6
Supply, absolute maximum
26 V · V+, absolute maximum supply voltage · p. 4
Works from
-40 °C · Minimum operating free-air temperature · p. 5
Works up to
125 °C · Maximum operating free-air temperature · p. 5
Junction, hottest
150 °C · Absolute maximum junction temperature · p. 4
Takes working
65 µA · Typical quiescent current, VSENSE = 0 mV · p. 6
Takes at most
115 µA · Maximum quiescent current at –40°C to 125°C · p. 6
A pin gives at most
5 mA · Absolute maximum input current into all pins · p. 4
Junction to air (DCK (SC70))
227.3 K/W · Junction-to-ambient thermal resistance · p. 5
Junction to case (DCK (SC70))
79.5 K/W · Junction-to-case top thermal resistance · p. 5
Junction to board (DCK (SC70))
72.1 K/W · Junction-to-board thermal resistance · p. 5
Junction to air (SC70)
250 K/W · Thermal resistance stated in electrical characteristics · p. 6

What it is and has

5
Gain
50 V/V · p. 1
Common-mode range
–0.3 V to 26 V · p. 1
Maximum offset voltage
±150 μV · p. 1
Maximum gain error over temperature
±1.5% · p. 1
Package options
6-Pin SC70, 10-Pin UQFN · p. 1

Around it

2
cap 0.1 µF
between V+ and GND; Power-supply bypass capacitor shown in Figure 7-1; required for stability and placed close to the device pins. · p. 12
cap 0.01 µF to 0.1 µF
between IN+ and IN–; Input transient filter capacitor used with ferrite beads for version A transient protection. · p. 17

Specifications

39
ParameterConditionsAs printedPage
Supply voltageOver operating free-air temperature rangemax 26 V4
Analog inputs, VIN+, VIN–Differential (VIN+) – (VIN–)min -26 · max 26 V4
Analog inputs, VIN+, VIN–Common-mode, INA199Ax; minimum GND – 0.3 Vmax 26 V4
Input current Into all pinsmax 5 mA4
Operating temperaturemin -40 · max 125 °C4
Junction temperaturemax 150 °C4
Storage temperature Tstgmin -65 · max 150 °C4
Electrostatic discharge V(ESD)INA199A1 in DCK package; Human-body model (HBM), per ANSI/ESDA/JEDEC JS-001; ±2000 Vmax 2000 V4
Electrostatic discharge V(ESD)INA199A1 in DCK package; Charged-device model (CDM), per JEDEC specification JESD22-C101; ±1000 Vmax 1000 V4
Common-mode input voltage VCMNominal valuetyp 12 V5
Operating supply voltage (applied to V+) VSNominal valuetyp 5 V5
Operating free-air temperature TAmin -40 · max 125 °C5
Junction-to-ambient thermal resistance RθJADCK (SC70), 6 pinstyp 227.3 °C/W5
Junction-to-case (top) thermal resistance RθJC(top)DCK (SC70), 6 pinstyp 79.5 °C/W5
Junction-to-board thermal resistance RθJBDCK (SC70), 6 pinstyp 72.1 °C/W5
Junction-to-top characterization parameter ψJTDCK (SC70), 6 pinstyp 3.6 °C/W5
Junction-to-board characterization parameter ψJBDCK (SC70), 6 pinstyp 70.4 °C/W5
Common-mode input range VCMVersion A, TA = –40°C to 125°Cmin -0.3 · max 26 V6
Common-mode rejection CMRVIN+ = 0 V to 26 V, VSENSE = 0 mV, TA = –40°C to 125°Cmin 100 · typ 120 dB6
Offset voltage, RTI VOSVSENSE = 0 mV; typical ±5 uV, maximum ±150 uVtyp 5 · max 150 uV6
VOS vs temperature dVOS/dTTA = –40°C to 125°Ctyp 0.1 · max 0.5 uV/°C6
Power supply rejection PSRVS = 2.7 V to 18 V, VIN+ = 18 V, VSENSE = 0 mV; typical ±0.1 uV/Vtyp 0.1 uV/V6
Input bias current IBVSENSE = 0 mVtyp 28 uA6
Input offset current IOSVSENSE = 0 mV; typical ±0.02 uAtyp 0.02 uA6
Gain GINA199x1typ 50 V/V6
Gain errorVersion A and B, VSENSE = –5 mV to 5 mV, TA = –40°C to 125°C; typical ±0.03%, maximum ±1.5%typ 0.03 · max 1.5 %6
Gain error vs temperatureTA = –40°C to 125°Ctyp 3 · max 10 ppm/°C6
Nonlinearity errorVSENSE = –5 mV to 5 mV; typical ±0.01%typ 0.01 %6
Maximum capacitive loadNo sustained oscillationtyp 1 nF6
Bandwidth GBWCLOAD = 10 pF, INA199x1typ 80 kHz6
Slew rate SRtyp 0.4 V/us6
Voltage noise densityRTItyp 25 nV/√ Hz6
Operating voltage range VSTA = –40°C to 125°Cmin 2.7 · max 26 V6
Operating voltage range VS–20°C to 85°Cmin 2.5 · max 26 V6
Quiescent current IQVSENSE = 0 mVtyp 65 · max 100 uA6
IQ over temperatureTA = –40°C to 125°Cmax 115 uA6
Specified rangemin -40 · max 125 °C6
Operating rangemin -40 · max 125 °C6
Thermal resistance θJASC70typ 250 °C/W6

Pins, by the datasheet

6
1 REF
Reference voltage, 0 V to V+. · p. 3
2 GND
Ground. · p. 3
3 V+
Power supply, 2.7 V to 26 V. · p. 3
4 IN+
Connect to supply side of shunt resistor. · p. 3
5 IN–
Connect to load side of shunt resistor. · p. 3
6 OUT
Output voltage. · p. 3

Open-source boards using it

5
  • 2 layers65 × 56 mmRadioberry preamp, the printed circuit board in 3D

    Radioberry preamp

    OE9SAU/SAUBerry9

    SDR TRX from Radioberry

    142 parts4
  • 4 layersMagneticLevitation, the printed circuit board in 3D

    MagneticLevitation

    dweggg/MagneticLevitation

    My take on one of those active magnetic levitation projects.

    149 parts
  • 2 layers55 × 55 mmRelay driver, the printed circuit board in 3D

    Relay driver

    IremAktas95/relay_driver

    🔗 Yüksek Performanslı Röle Sürücü Devresi

    34 parts

Parts like it

8

Questions

Is there a KiCad symbol and footprint for the INA199A1DCK?

Yes. The symbol is Amplifier_Current:INA199xxDCK and the footprint Package_TO_SOT_SMD:SOT-363_SC-70-6, both drawn on this page. PCBKit places them on a board for you when you design with it.

What package is the INA199A1DCK?

SC-70-6, with 6 pins. Its footprint is drawn on this page.

Where is the INA199A1DCK datasheet?

Texas Instruments publishes it: the Datasheet link on this page opens it.

Where can I order the INA199A1DCK?

JLCPCB lists it as part C59135, with 66,309 in stock; the sellers' links on this page open their listings.

What can replace the INA199A1DCK?

Parts like it in the library: the INA213AIDCK by Texas Instruments, the INA199A2DCK by Texas Instruments, the INA214AIDCK by Texas Instruments and the INA186A3IDCK by Texas Instruments. Check their datasheets: a part that fits the footprint may still differ in its ratings.

Which open-source boards use the INA199A1DCK?

5 boards in 3 repositories on GitHub; the most starred are listed on this page, with their KiCad files.