Skip to the content
1234567891011121314151617

DRV8847PWP

Texas InstrumentsExtended

-40℃~+85℃ 1A 1Ω 2 2.7V~18V Bipolar Driver I2C Yes HTSSOP-16-EP Stepper Motor Driver ROHS

Part id
ti/DRV8847PWP
Category
Stepper Motor Driver
Package
HTSSOP-16-EP
Pins
17
In stock
538 at JLCPCB (C544361)
Used on
1 open-source board

Overview

The DRV8847PWP is a stepper Motor Driver made by Texas Instruments in a HTSSOP-16-EP package with 17 pins. -40℃~+85℃ 1A 1Ω 2 2.7V~18V Bipolar Driver I2C Yes HTSSOP-16-EP Stepper Motor Driver ROHS.

PCBKit's library has its KiCad symbol (Driver_Motor:DRV8847PWP, from KiCad's library) and its footprint (Package_SO:HTSSOP-16-1EP_4.4x5mm_P0.65mm_EP3.4x5mm_Mask2.46x2.31mm, from KiCad's library), ready for a KiCad board. 538 are in stock at JLCPCB (part C544361). 1 open-source board in 1 repository on GitHub use it.

Symbol

1SLEEP2OUT13ISEN124OUT25OUT46ISEN347OUT38FAULT9IN310IN411TRQ12VM13GND14MODE15IN216IN117PPAD
Driver_Motor:DRV8847PWPFrom KiCad's library

Footprint

1234567891011121314151617
Package_SO:HTSSOP-16-1EP_4.4x5mm_P0.65mm_EP3.4x5mm_Mask2.46x2.31mmFrom KiCad's library

From the datasheet

14
Supply, least
2.7 V · VM, recommended operating min · p. 7
Supply, most
18 V · VM, recommended operating max · p. 7
Supply, absolute maximum
20 V · VM, absolute maximum · p. 7
Works from
-40 °C · Operating ambient temperature min · p. 7
Works up to
85 °C · Operating ambient temperature max · p. 7
Junction, hottest
150 °C · Operating junction temperature max · p. 7
Takes working
3 mA · VM operating supply current typical, VM = 12 V; nSLEEP = 1; INX = 0 · p. 8
Takes asleep
1.7 µA · VM sleep current typical, VM = 12 V; TA = 25°C · p. 8
Gives
1 A · Motor RMS current per bridge max · p. 7
Current limit
2 A · Overcurrent protection trip point typical · p. 9
Edge
150 ns · Output rise time typical, VVM = 12 V; IOUT = 0.5 A · p. 9
Junction to air (PWP (HTSSOP))
46.5 K/W · Junction-to-ambient thermal resistance typical · p. 7
Junction to case (PWP (HTSSOP))
40.1 K/W · Junction-to-case top thermal resistance typical · p. 8
Junction to board (PWP (HTSSOP))
18.8 K/W · Junction-to-board thermal resistance typical · p. 8

What it is and has

17
Driver
Dual H-bridge motor driver · p. 1
Motor support
Single or dual-brushed DC motors · p. 1
Motor support
One bipolar stepper motor · p. 1
Load support
Solenoid loads · p. 1
Control interface
4-Pin interface · p. 1
Control interface
2-Pin interface · p. 1
Control interface
Parallel bridge interface · p. 1
Control interface
Independent bridge interface · p. 1
Current regulation
20-μs fixed off-time · p. 1
Torque scalar
Scales output current to 50% · p. 1
Logic inputs
1.8 V, 3.3 V, 5 V · p. 1
Protection
VM undervoltage lockout · p. 1
Protection
Overcurrent protection · p. 1
Protection
Open load detection · p. 1
Protection
Thermal shutdown · p. 1
Fault indication
nFAULT pin · p. 1
Package
16 Pin HTSSOP PowerPAD · p. 1

Around it

2
cap 0.1-µF
between VM and GND; VM-rated ceramic bypass capacitor. · p. 5
cap 10-μF (minimum)
between VM and GND; VM-rated bypass capacitor. · p. 5

Specifications

98
ParameterConditionsAs printedPage
Power supply pin voltage (VM)min -0.3 · max 20 V7
Power supply voltage ramp rate (VM)min 0 · max 2 V/us7
Digital pin voltage (IN1, IN2, IN3, IN4, TRQ, nSLEEP, nFAULT, SCL, SDA)min -0.3 · max 5.75 V7
Continuous phase node pin voltage (OUT1, OUT2, OUT3, OUT4)Maximum = VM + 0.6 Vmin -0.7 V7
Shunt amplifier input pin voltage (ISEN12, ISEN34)min -0.6 · max 0.6 V7
Peak drive current (OUT1, OUT2, OUT3, OUT4)VVM > 16.5 Vmin 0 · max 4 A7
Ambient temperature, TA TAmin -40 · max 125 °C7
Junction temperature, TJ TJmin -40 · max 150 °C7
Storage temperature, Tstg Tstgmin -65 · max 150 °C7
Electrostatic discharge V(ESD)Human body model (HBM), per ANSI/ESDA/JEDEC JS-001, all pins; ±4000 Vmax 4000 V7
Electrostatic discharge V(ESD)Charged device model (CDM), per JEDEC specification JESD22-C101, all pins; ±500 Vmax 500 V7
Power supply voltage (VM) VVMmin 2.7 · max 18 V7
Logic input voltage (IN1, IN2, IN3, IN4, TRQ, nSLEEP, SCL, SDA) VINmin 0 · max 5 V7
Motor RMS current per bridge (OUT1, OUT2, OUT3, OUT4) IRMSPower dissipation and thermal limits must be observed; dependent on package thermal performancemin 0 · max 1 A7
PWM frequency (IN1, IN2, IN3, IN4) fPWMPower dissipation and thermal limits must be observed; dependent on package thermal performancemin 0 · max 250 kHz7
Open drain pullup voltage (nFAULT) VODmin 0 · max 5 V7
Open drain output current (nFAULT) IODmin 0 · max 5 mA7
Operating Ambient Temperature TAmin -40 · max 85 °C7
Operating Junction Temperature TJmin -40 · max 150 °C7
Junction-to-ambient thermal resistance Rθ JADRV8847, PWP (HTSSOP), 16 PINStyp 46.5 °C/W7
Junction-to-case (top) thermal resistance RθJC(top)DRV8847, PWP (HTSSOP), 16 PINStyp 40.1 °C/W8
Junction-to-board thermal resistance RθJBDRV8847, PWP (HTSSOP), 16 PINStyp 18.8 °C/W8
Junction-to-top characterization parameter ΨJTDRV8847, PWP (HTSSOP), 16 PINStyp 1.3 °C/W8
Junction-to-board characterization parameter ΨJBDRV8847, PWP (HTSSOP), 16 PINStyp 19 °C/W8
Junction-to-case (bottom) thermal resistance RθJC(bot)DRV8847, PWP (HTSSOP), 16 PINStyp 5.9 °C/W8
VM operating supply current IVMVM = 2.7 V; nSLEEP = 1; INX = 0typ 2 · max 2.5 mA8
VM operating supply current IVMVM = 5 V; nSLEEP = 1; INX = 0typ 3 · max 3.5 mA8
VM operating supply current IVMVM = 12 V; nSLEEP = 1; INX = 0typ 3 · max 3.5 mA8
VM sleep mode current IVMQVM = 2.7 V; nSLEEP = 0; TA = 25°Ctyp 0.1 uA8
VM sleep mode current IVMQVM = 2.7 V; nSLEEP = 0; TA = 85°Cmax 0.5 uA8
VM sleep mode current IVMQVM = 5 V; nSLEEP = 0; TA = 25°Ctyp 0.2 uA8
VM sleep mode current IVMQVM = 5 V; nSLEEP = 0; TA = 85°Cmax 1 uA8
VM sleep mode current IVMQVM = 12 V; nSLEEP = 0; TA = 25°Ctyp 1.7 uA8
VM sleep mode current IVMQVM = 12 V; nSLEEP = 0; TA = 85°Cmax 2.5 uA8
Sleep time tSLEEPnSLEEP = 0 to sleep modetyp 2 us8
Wake-up time tWAKEnSLEEP = 1 to output transitionmax 1.5 ms8
Turnon-time tONVM > UVLO to output transition (nSLEEP = 1)max 1.5 ms8
Input logic low voltage VILVM < 7 Vmin 0 · max 0.6 V8
Input logic low voltage VILVM >= 7 Vmin 0 · max 1 V8
Input logic high voltage VIHmin 1.6 · max 5.5 V8
Input logic hysteresis VHYSnSLEEP pinmin 40 mV8
Input logic hysteresis VHYSIN1, IN2, IN3, IN4, TRQ, SCL pinsmin 100 mV8
nSLEEP VILmin 0 · max 0.6 V8
nSLEEP VIHmin 1.6 · max 5.5 V8
nSLEEP VHYSmin 40 mV8
Input logic low current IILVIN = 0 Vmin -1 · max 1 uA8
Input logic high current IIHIN1, IN2, IN3, IN4, TRQ, VIN = 5 Vmin 18 · max 35 uA8
Input logic high current IIHnSLEEP, VIN = minimum (VM, 5 V)min 10 · max 25 uA8
Propagation Delay tPDINx edge to outputmin 100 · typ 400 · max 600 ns8
Input logic deglitch tDEGLITCHtyp 50 ns8
Tri-level input logic low voltage VILMODEmin 0 · max 0.6 V8
Tri-level input hi-Z voltage VIZMODEtyp 1.2 V8
Tri-level input logic high voltage VIHMODEmin 1.6 · max 5.5 V8
Tri-level input logic low current IILMODE; VIN = 0 Vmin -9 · max -4 uA8
Tri-level input logic high current IIHMODE; VIN = 5 Vmin 8 · max 25 uA9
Output logic low voltage VOLnFAULT; IOD = 5 mAmax 0.5 V9
Output logic high current IOHnFAULT; VOD = 3.3 Vmin -1 · max 1 uA9
High-side MOSFET on resistance RDS(ON)_HSVVM = 2.7 V; IOUT = 0.5 A; TA = 25°Ctyp 690 mΩ9
High-side MOSFET on resistance RDS(ON)_HSVVM = 2.7 V; IOUT = 0.5 A; TA = 85°Cmax 950 mΩ9
High-side MOSFET on resistance RDS(ON)_HSVVM = 5 V; IOUT = 0.5 A; TA = 25°Ctyp 530 mΩ9
High-side MOSFET on resistance RDS(ON)_HSVVM = 5 V; IOUT = 0.5 A; TA = 85°Cmax 740 mΩ9
High-side MOSFET on resistance RDS(ON)_HSVVM = 12 V; IOUT = 0.5 A; TA = 25°Ctyp 520 mΩ9
High-side MOSFET on resistance RDS(ON)_HSVVM = 12 V; IOUT = 0.5 A; TA = 85°Cmax 700 mΩ9
Low-side MOSFET on resistance RDS(ON)_LSVVM = 2.7 V; IOUT = 0.5 A; TA = 25°Ctyp 570 mΩ9
Low-side MOSFET on resistance RDS(ON)_LSVVM = 2.7 V; IOUT = 0.5 A; TA = 85°Cmax 900 mΩ9
Low-side MOSFET on resistance RDS(ON)_LSVVM = 5 V; IOUT = 0.5 A; TA = 25°Ctyp 460 mΩ9
Low-side MOSFET on resistance RDS(ON)_LSVVM = 5 V; IOUT = 0.5 A; TA = 85°Cmax 690 mΩ9
Low-side MOSFET on resistance RDS(ON)_LSVVM = 12 V; IOUT = 0.5 A; TA = 25°Ctyp 450 mΩ9
Low-side MOSFET on resistance RDS(ON)_LSVVM = 12 V; IOUT = 0.5 A; TA = 85°Cmax 680 mΩ9
Off-state leakage current IOFFVVM = 5 V; TJ = 25 °C; VOUT = 0 Vmin -1 · max 1 uA9
Output rise time tRISEVVM = 12 V; IOUT = 0.5 Atyp 150 ns9
Output fall time tFALLVVM = 12 V, IOUT = 0.5 Atyp 150 ns9
Output dead time tDEADInternal dead timetyp 200 ns9
Body diode forward voltage VSDIOUT = 0.5 Atyp 1.1 V9
ISENxx trip voltage VTRIPTorque at 100% (TRQ = 0)min 140 · typ 150 · max 160 mV9
ISENxx trip voltage VTRIPTorque at 50% (TRQ = 1)min 63.75 · typ 75 · max 86.25 mV9
Current sense blanking time tBLANKtyp 1.8 us9
Current control constant off time tOFFtyp 20 us9
Supply undervoltage lockout VUVLOSupply risingmax 2.7 V9
Supply undervoltage lockout VUVLOSupply fallingmin 2.4 V9
Supply undervoltage hysteresis VUVLO_HYSRising to falling thesholdtyp 50 mV9
Supply undervoltage deglitch time tUVLOVM falling; UVLO reporttyp 10 us9
Overcurrent protection trip point IOCPmin 1.6 · typ 2 A9
Overcurrent protection deglitch time tOCPVVM < 15 Vtyp 3 us9
Overcurrent protection deglitch time tOCPVVM >= 15 Vtyp 1 us9
Overcurrent protection retry time tRETRYtyp 1 ms9
Open load pull up current IOL_PU< 15 nF on OUTx Pin, VVM = 2.7 Vtyp 100 uA9
Open load pull-up current IOL_PU< 15 nF on OUTx Pintyp 200 uA9
Open load pull down current IOL_PD< 15 nF on OUTx Pin, VVM = 2.7 Vtyp 130 uA9
Open load pull-down current IOL_PD< 15 nF on OUTx Pintyp 230 uA9
Open load pull up and pull down current IOLtyp 230 uA9
Open load detect threshold (high side) VOL_HSVVM = 2.7 Vtyp 1.3 V10
Open load detect threshold (high side) VOL_HStyp 2.3 V10
Open load detect threshold (low side) VOL_LSVVM = 2.7 Vtyp 0.67 V10
Open load detect threshold (low side) VOL_LStyp 1.2 V10
Open load detect threshold voltage VOLtyp 1.1 V10
Thermal shutdown temperature TTSDmin 150 · typ 160 · max 180 °C10
Thermal shutdown hysteresis THYStyp 40 °C10

Pins, by the datasheet

16
1 nSLEEP
Set high to enable the device; set low for low-power sleep mode. · p. 5
2 OUT1
Half-bridge output 1. · p. 5
3 ISEN12
Full-bridge-12 sense; connect to the current sense resistor, or GND if current regulation is not required. · p. 5
4 OUT2
Half-bridge output 2. · p. 5
5 OUT4
Half-bridge output 4. · p. 5
6 ISEN34
Full-bridge-34 sense; connect to the current sense resistor, or GND if current regulation is not required. · p. 5
7 OUT3
Half-bridge output 3. · p. 5
8 nFAULT
Fault indication pulled low during a fault; requires an external pullup resistor. · p. 5
9 IN3
Half-bridge input 3. · p. 5
10 IN4
Half-bridge input 4. · p. 5
11 TRQ
Torque current scalar. · p. 5
12 VM
Motor power supply; bypass to ground with a VM-rated 0.1-uF ceramic capacitor and a 10-uF minimum capacitor. · p. 5
13 GND
Device ground; connect the GND pin and thermal pad to ground. · p. 5
14 MODE
Tri-state pin selecting the driver operating mode. · p. 5
15 IN2
Half-bridge input 2. · p. 5
16 IN1
Half-bridge input 1. · p. 5

Open-source boards using it

1
  • 2 layers65 × 30 mmWRO-2025-Future Engineers Canada, the printed circuit board in 3D

    WRO-2025-Future Engineers Canada

    teostefan/WRO-2025-Future-Engineers-Canada

    Main repository for the joint uOttawa-CarletonU team competing in the WRO Future Engineers 2025 competition.

    36 parts2

Parts like it

2

Questions

Is there a KiCad symbol and footprint for the DRV8847PWP?

Yes. The symbol is Driver_Motor:DRV8847PWP and the footprint Package_SO:HTSSOP-16-1EP_4.4x5mm_P0.65mm_EP3.4x5mm_Mask2.46x2.31mm, both drawn on this page. PCBKit places them on a board for you when you design with it.

What package is the DRV8847PWP?

HTSSOP-16-EP, with 17 pins. Its footprint is drawn on this page.

Where is the DRV8847PWP datasheet?

Texas Instruments publishes it: the Datasheet link on this page opens it.

Where can I order the DRV8847PWP?

JLCPCB lists it as part C544361, with 538 in stock; the sellers' links on this page open their listings.

What can replace the DRV8847PWP?

Parts like it in the library: the DRV8833PWPR by Texas Instruments and the DRV8833PWP by Texas Instruments. Check their datasheets: a part that fits the footprint may still differ in its ratings.

Which open-source boards use the DRV8847PWP?

1 board in 1 repository on GitHub; the most starred are listed on this page, with their KiCad files.