
OpenFlops
silvervest/OpenFlops-W1D
Modified OpenFlops specifically to replace Citizen W1D drives
STMicroelectronicsExtended
-40℃~+85℃ 128KB 12bit 12bit 2V~3.6V 32 Bit 51 64KB 72MHz ARM Cortex-M3 Built-in FLASH LQFP-64(10x10) Microcontrollers (MCU/MPU/SOC) ROHS
The STM32F105RBT6 is a microcontroller made by STMicroelectronics in a LQFP-64(10x10) package with 64 pins. -40℃~+85℃ 128KB 12bit 12bit 2V~3.6V 32 Bit 51 64KB 72MHz ARM Cortex-M3 Built-in FLASH LQFP-64(10x10) Microcontrollers (MCU/MPU/SOC) ROHS.
PCBKit's library has its KiCad symbol (MCU_ST_STM32F1:STM32F105RBTx, from KiCad's library) and its footprint (Package_QFP:LQFP-64_10x10mm_P0.5mm, from KiCad's library), ready for a KiCad board. 3,735 are in stock at JLCPCB (part C8349). 6 open-source boards in 6 repositories on GitHub use it.
| Parameter | Conditions | As printed | Page |
|---|---|---|---|
| External main supply voltage (including VDDA and VDD) VDD–VSS | Absolute maximum | min -0.3 · max 4 V | 36 |
| Input voltage on any other pin VIN | Absolute maximum; minimum VSS − 0.3 | max 4 V | 36 |
| Variations between different VDD power pins |ΔVDDx| | max 50 mV | 36 | |
| Variations between all the different ground pins |VSSX − VSS| | max 50 mV | 36 | |
| Total current into VDD/VDDA power lines (source) IVDD | Absolute maximum | max 150 mA | 36 |
| Total current out of VSS ground lines (sink) IVSS | Absolute maximum | max 150 mA | 36 |
| Output current sunk by any I/O and control pin IIO | Absolute maximum | max 25 mA | 36 |
| Output current source by any I/Os and control pin IIO | Absolute maximum | max -25 mA | 36 |
| Injected current on five volt tolerant pins IINJ(PIN) | Absolute maximum, -5/+0 mA | min -5 · max 0 mA | 36 |
| Injected current on any other pin IINJ(PIN) | Absolute maximum, ±5 mA | min -5 · max 5 mA | 36 |
| Total injected current (sum of all I/O and control pins) ΣIINJ(PIN) | Absolute maximum, ±25 mA; absolute sum of positive and negative injected currents | min -25 · max 25 mA | 36 |
| Storage temperature range TSTG | Absolute maximum | min -65 · max 150 °C | 37 |
| Maximum junction temperature TJ | Absolute maximum | max 150 °C | 37 |
| Internal AHB clock frequency fHCLK | min 0 · max 72 MHz | 37 | |
| Internal APB1 clock frequency fPCLK1 | min 0 · max 36 MHz | 37 | |
| Internal APB2 clock frequency fPCLK2 | min 0 · max 72 MHz | 37 | |
| Standard operating voltage VDD | min 2 · max 3.6 V | 37 | |
| Analog operating voltage (ADC not used) VDDA | Must be the same potential as VDD | min 2 · max 3.6 V | 37 |
| Analog operating voltage (ADC used) VDDA | Must be the same potential as VDD | min 2.4 · max 3.6 V | 37 |
| Backup operating voltage VBAT | min 1.8 · max 3.6 V | 37 | |
| Power dissipation at TA = 85 °C for suffix 6 or TA = 105 °C for suffix 7 PD | LQFP64; footnote 3 | max 444 mW | 37 |
| Power dissipation at TA = 85 °C for suffix 6 or TA = 105 °C for suffix 7 PD | LQFP64; footnote 4 | max 444 mW | 37 |
| Ambient temperature for 6 suffix version TA | Maximum power dissipation | min -40 · max 85 °C | 37 |
| Ambient temperature for 6 suffix version TA | Low power dissipation; TJ must not exceed TJmax | min -40 · max 105 °C | 37 |
| Junction temperature range TJ | 6 suffix version | min -40 · max 105 °C | 37 |
| VDD rise time rate tVDD | Subject to general operating conditions for TA | min 0 us/V | 38 |
| VDD fall time rate TJ | Subject to general operating conditions for TA | min 20 us/V | 38 |
| Programmable voltage detector level selection VPVD | PLS[2:0]=000 (rising edge) | min 2.1 · typ 2.18 · max 2.26 V | 38 |
| Programmable voltage detector level selection VPVD | PLS[2:0]=000 (falling edge) | min 2 · typ 2.08 · max 2.16 V | 38 |
| Programmable voltage detector level selection VPVD | PLS[2:0]=001 (rising edge) | min 2.19 · typ 2.28 · max 2.37 V | 38 |
| Programmable voltage detector level selection VPVD | PLS[2:0]=001 (falling edge) | min 2.09 · typ 2.18 · max 2.27 V | 38 |
| Programmable voltage detector level selection VPVD | PLS[2:0]=010 (rising edge) | min 2.28 · typ 2.38 · max 2.48 V | 38 |
| Programmable voltage detector level selection VPVD | PLS[2:0]=010 (falling edge) | min 2.18 · typ 2.28 · max 2.38 V | 38 |
| Programmable voltage detector level selection VPVD | PLS[2:0]=011 (rising edge) | min 2.38 · typ 2.48 · max 2.58 V | 38 |
| Programmable voltage detector level selection VPVD | PLS[2:0]=011 (falling edge) | min 2.28 · typ 2.38 · max 2.48 V | 38 |
| Programmable voltage detector level selection VPVD | PLS[2:0]=100 (rising edge) | min 2.47 · typ 2.58 · max 2.69 V | 38 |
| Programmable voltage detector level selection VPVD | PLS[2:0]=100 (falling edge) | min 2.37 · typ 2.48 · max 2.59 V | 38 |
| Programmable voltage detector level selection VPVD | PLS[2:0]=101 (rising edge) | min 2.57 · typ 2.68 · max 2.79 V | 38 |
| Programmable voltage detector level selection VPVD | PLS[2:0]=101 (falling edge) | min 2.47 · typ 2.58 · max 2.69 V | 38 |
| Programmable voltage detector level selection VPVD | PLS[2:0]=110 (rising edge) | min 2.66 · typ 2.78 · max 2.9 V | 38 |
| Programmable voltage detector level selection VPVD | PLS[2:0]=110 (falling edge) | min 2.56 · typ 2.68 · max 2.8 V | 38 |
| Programmable voltage detector level selection VPVD | PLS[2:0]=111 (rising edge) | min 2.76 · typ 2.88 · max 3 V | 38 |
| Programmable voltage detector level selection VPVD | PLS[2:0]=111 (falling edge) | min 2.66 · typ 2.78 · max 2.9 V | 38 |
| PVD hysteresis VPVDhyst | Guaranteed by design, not tested in production | typ 100 mV | 38 |
| Power on/power down reset threshold VPOR/PDR | Falling edge | min 1.8 · typ 1.88 · max 1.96 V | 38 |
| Power on/power down reset threshold VPOR/PDR | Rising edge | min 1.84 · typ 1.92 · max 2 V | 38 |
| PDR hysteresis VPDRhyst | Guaranteed by design, not tested in production | typ 40 mV | 38 |
| Reset temporization TRSTTEMPO | Guaranteed by design, not tested in production | min 1 · typ 2.5 · max 4.5 ms | 38 |
| Internal reference voltage VREFINT | –40 °C < TA < +105 °C | min 1.16 · typ 1.2 · max 1.26 V | 39 |
| Internal reference voltage VREFINT | –40 °C < TA < +85 °C | min 1.16 · typ 1.2 · max 1.24 V | 39 |
| ADC sampling time when reading the internal reference voltage TS_vrefint | Shortest sampling time determined in application by multiple iterations | typ 5.1 · max 17.1 us | 39 |
| Internal reference voltage spread over the temperature range VRERINT | VDD = 3 V ±10 mV; guaranteed by design, not tested in production | max 10 mV | 39 |
| Temperature coefficient TCoeff | Guaranteed by design, not tested in production | max 100 ppm/°C | 39 |
| Supply current in Run mode IDD | External clock, all peripherals enabled; fHCLK = 72 MHz; TA = 85 °C | max 68 mA | 40 |
| Supply current in Run mode IDD | External clock, all peripherals enabled; fHCLK = 72 MHz; TA = 105 °C | max 68.4 mA | 40 |
| Supply current in Run mode IDD | External clock, all peripherals enabled; fHCLK = 48 MHz; TA = 85 °C | max 49 mA | 40 |
| Supply current in Run mode IDD | External clock, all peripherals enabled; fHCLK = 48 MHz; TA = 105 °C | max 49.2 mA | 40 |
| Supply current in Run mode IDD | External clock, all peripherals enabled; fHCLK = 36 MHz; TA = 85 °C | max 38.7 mA | 40 |
| Supply current in Run mode IDD | External clock, all peripherals enabled; fHCLK = 36 MHz; TA = 105 °C | max 38.9 mA | 40 |
| Supply current in Run mode IDD | External clock, all peripherals enabled; fHCLK = 24 MHz; TA = 85 °C | max 27.3 mA | 40 |
| Supply current in Run mode IDD | External clock, all peripherals enabled; fHCLK = 24 MHz; TA = 105 °C | max 27.9 mA | 40 |
| Supply current in Run mode IDD | External clock, all peripherals enabled; fHCLK = 16 MHz; TA = 85 °C | max 20.2 mA | 40 |
| Supply current in Run mode IDD | External clock, all peripherals enabled; fHCLK = 16 MHz; TA = 105 °C | max 20.5 mA | 40 |
| Supply current in Run mode IDD | External clock, all peripherals enabled; fHCLK = 8 MHz; TA = 85 °C | max 10.2 mA | 40 |
| Supply current in Run mode IDD | External clock, all peripherals enabled; fHCLK = 8 MHz; TA = 105 °C | max 10.8 mA | 40 |
| Supply current in Run mode IDD | External clock, all peripherals disabled; fHCLK = 72 MHz; TA = 85 °C | max 32.7 mA | 40 |
| Supply current in Run mode IDD | External clock, all peripherals disabled; fHCLK = 72 MHz; TA = 105 °C | max 32.9 mA | 40 |
| Supply current in Run mode IDD | External clock, all peripherals disabled; fHCLK = 48 MHz; TA = 85 °C | max 25 mA | 40 |
| Supply current in Run mode IDD | External clock, all peripherals disabled; fHCLK = 48 MHz; TA = 105 °C | max 25.2 mA | 40 |
| Supply current in Run mode IDD | External clock, all peripherals disabled; fHCLK = 36 MHz; TA = 85 °C | max 20.3 mA | 40 |
| Supply current in Run mode IDD | External clock, all peripherals disabled; fHCLK = 36 MHz; TA = 105 °C | max 20.6 mA | 40 |
| Supply current in Run mode IDD | External clock, all peripherals disabled; fHCLK = 24 MHz; TA = 85 °C | max 14.8 mA | 40 |
| Supply current in Run mode IDD | External clock, all peripherals disabled; fHCLK = 24 MHz; TA = 105 °C | max 15.1 mA | 40 |
| Supply current in Run mode IDD | External clock, all peripherals disabled; fHCLK = 16 MHz; TA = 85 °C | max 11.2 mA | 40 |
| Supply current in Run mode IDD | External clock, all peripherals disabled; fHCLK = 16 MHz; TA = 105 °C | max 11.7 mA | 40 |
| Supply current in Run mode IDD | External clock, all peripherals disabled; fHCLK = 8 MHz; TA = 85 °C | max 6.6 mA | 40 |
| Supply current in Run mode IDD | External clock, all peripherals disabled; fHCLK = 8 MHz; TA = 105 °C | max 7.2 mA | 40 |
| Supply current in Run mode IDD | External clock, all peripherals enabled; fHCLK = 72 MHz; TA = 85 °C | max 65.5 mA | 40 |
| Supply current in Run mode IDD | External clock, all peripherals enabled; fHCLK = 72 MHz; TA = 105 °C | max 66 mA | 40 |
| Supply current in Run mode IDD | External clock, all peripherals enabled; fHCLK = 48 MHz; TA = 85 °C | max 45.4 mA | 40 |
| Supply current in Run mode IDD | External clock, all peripherals enabled; fHCLK = 48 MHz; TA = 105 °C | max 46 mA | 40 |
| Supply current in Run mode IDD | External clock, all peripherals enabled; fHCLK = 36 MHz; TA = 85 °C | max 35.5 mA | 40 |
| Supply current in Run mode IDD | External clock, all peripherals enabled; fHCLK = 36 MHz; TA = 105 °C | max 36.1 mA | 40 |
| Supply current in Run mode IDD | External clock, all peripherals enabled; fHCLK = 24 MHz; TA = 85 °C | max 25.2 mA | 40 |
| Supply current in Run mode IDD | External clock, all peripherals enabled; fHCLK = 24 MHz; TA = 105 °C | max 25.6 mA | 40 |
| Supply current in Run mode IDD | External clock, all peripherals enabled; fHCLK = 16 MHz; TA = 85 °C | max 18 mA | 40 |
| Supply current in Run mode IDD | External clock, all peripherals enabled; fHCLK = 16 MHz; TA = 105 °C | max 18.5 mA | 40 |
| Supply current in Run mode IDD | External clock, all peripherals enabled; fHCLK = 8 MHz; TA = 85 °C | max 10.5 mA | 40 |
| Supply current in Run mode IDD | External clock, all peripherals enabled; fHCLK = 8 MHz; TA = 105 °C | max 11 mA | 40 |
| Supply current in Run mode IDD | External clock, all peripherals disabled; fHCLK = 72 MHz; TA = 85 °C | max 31.4 mA | 40 |
| Supply current in Run mode IDD | External clock, all peripherals disabled; fHCLK = 72 MHz; TA = 105 °C | max 31.9 mA | 40 |
| Supply current in Run mode IDD | External clock, all peripherals disabled; fHCLK = 48 MHz; TA = 85 °C | max 27.8 mA | 40 |
| Supply current in Run mode IDD | External clock, all peripherals disabled; fHCLK = 48 MHz; TA = 105 °C | max 28.2 mA | 40 |
| Supply current in Run mode IDD | External clock, all peripherals disabled; fHCLK = 36 MHz; TA = 85 °C | max 17.6 mA | 40 |
| Supply current in Run mode IDD | External clock, all peripherals disabled; fHCLK = 36 MHz; TA = 105 °C | max 18.3 mA | 40 |
| Supply current in Run mode IDD | External clock, all peripherals disabled; fHCLK = 24 MHz; TA = 85 °C | max 13.1 mA | 40 |
| Supply current in Run mode IDD | External clock, all peripherals disabled; fHCLK = 24 MHz; TA = 105 °C | max 13.8 mA | 40 |
| Supply current in Run mode IDD | External clock, all peripherals disabled; fHCLK = 16 MHz; TA = 85 °C | max 10.2 mA | 40 |
| Supply current in Run mode IDD | External clock, all peripherals disabled; fHCLK = 16 MHz; TA = 105 °C | max 10.9 mA | 40 |
| Supply current in Run mode IDD | External clock, all peripherals disabled; fHCLK = 8 MHz; TA = 85 °C | max 6.1 mA | 40 |
| Supply current in Run mode IDD | External clock, all peripherals disabled; fHCLK = 8 MHz; TA = 105 °C | max 7.8 mA | 40 |
| Supply current in Sleep mode IDD | External clock, all peripherals enabled; fHCLK = 72 MHz; TA = 85 °C | max 48.4 mA | 41 |
| Supply current in Sleep mode IDD | External clock, all peripherals enabled; fHCLK = 72 MHz; TA = 105 °C | max 49 mA | 41 |
| Supply current in Sleep mode IDD | External clock, all peripherals enabled; fHCLK = 48 MHz; TA = 85 °C | max 33.9 mA | 41 |
| Supply current in Sleep mode IDD | External clock, all peripherals enabled; fHCLK = 48 MHz; TA = 105 °C | max 34.4 mA | 41 |
| Supply current in Sleep mode IDD | External clock, all peripherals enabled; fHCLK = 36 MHz; TA = 85 °C | max 26.7 mA | 41 |
| Supply current in Sleep mode IDD | External clock, all peripherals enabled; fHCLK = 36 MHz; TA = 105 °C | max 27.2 mA | 41 |
| Supply current in Sleep mode IDD | External clock, all peripherals enabled; fHCLK = 24 MHz; TA = 85 °C | max 19.3 mA | 41 |
| Supply current in Sleep mode IDD | External clock, all peripherals enabled; fHCLK = 24 MHz; TA = 105 °C | max 19.8 mA | 41 |
| Supply current in Sleep mode IDD | External clock, all peripherals enabled; fHCLK = 16 MHz; TA = 85 °C | max 14.2 mA | 41 |
| Supply current in Sleep mode IDD | External clock, all peripherals enabled; fHCLK = 16 MHz; TA = 105 °C | max 14.8 mA | 41 |
| Supply current in Sleep mode IDD | External clock, all peripherals enabled; fHCLK = 8 MHz; TA = 85 °C | max 8.7 mA | 41 |
| Supply current in Sleep mode IDD | External clock, all peripherals enabled; fHCLK = 8 MHz; TA = 105 °C | max 9.1 mA | 41 |
| Supply current in Sleep mode IDD | External clock, all peripherals disabled; fHCLK = 72 MHz; TA = 85 °C | max 10.1 mA | 41 |
| Supply current in Sleep mode IDD | External clock, all peripherals disabled; fHCLK = 72 MHz; TA = 105 °C | max 10.6 mA | 41 |
| Supply current in Sleep mode IDD | External clock, all peripherals disabled; fHCLK = 48 MHz; TA = 85 °C | max 8.3 mA | 41 |
| Supply current in Sleep mode IDD | External clock, all peripherals disabled; fHCLK = 48 MHz; TA = 105 °C | max 8.75 mA | 41 |
| Supply current in Sleep mode IDD | External clock, all peripherals disabled; fHCLK = 36 MHz; TA = 85 °C | max 7.5 mA | 41 |
| Supply current in Sleep mode IDD | External clock, all peripherals disabled; fHCLK = 36 MHz; TA = 105 °C | max 8 mA | 41 |
| Supply current in Sleep mode IDD | External clock, all peripherals disabled; fHCLK = 24 MHz; TA = 85 °C | max 6.6 mA | 41 |
| Supply current in Sleep mode IDD | External clock, all peripherals disabled; fHCLK = 24 MHz; TA = 105 °C | max 7.1 mA | 41 |
| Supply current in Sleep mode IDD | External clock, all peripherals disabled; fHCLK = 16 MHz; TA = 85 °C | max 6 mA | 41 |
| Supply current in Sleep mode IDD | External clock, all peripherals disabled; fHCLK = 16 MHz; TA = 105 °C | max 6.5 mA | 41 |
| Supply current in Sleep mode IDD | External clock, all peripherals disabled; fHCLK = 8 MHz; TA = 85 °C | max 2.5 mA | 41 |
| Supply current in Sleep mode IDD | External clock, all peripherals disabled; fHCLK = 8 MHz; TA = 105 °C | max 3 mA | 41 |
| Supply current in Stop mode IDD | Regulator in Run mode; low-speed and high-speed internal RC oscillators and high-speed oscillator OFF; no independent watchdog; VDD = 2.4 V; TA = 25 °C | typ 32 uA | 41 |
| Supply current in Stop mode IDD | Regulator in Run mode; low-speed and high-speed internal RC oscillators and high-speed oscillator OFF; no independent watchdog; VDD = 3.3 V; TA = 25 °C | typ 33 uA | 41 |
| Supply current in Stop mode IDD | Regulator in Run mode; low-speed and high-speed internal RC oscillators and high-speed oscillator OFF; no independent watchdog; TA = 85 °C | max 600 uA | 41 |
| Supply current in Stop mode IDD | Regulator in Run mode; low-speed and high-speed internal RC oscillators and high-speed oscillator OFF; no independent watchdog; TA = 105 °C | max 1300 uA | 41 |
| Supply current in Stop mode IDD | Regulator in Low Power mode; low-speed and high-speed internal RC oscillators and high-speed oscillator OFF; no independent watchdog; VDD = 2.4 V; TA = 25 °C | typ 25 uA | 41 |
| Supply current in Stop mode IDD | Regulator in Low Power mode; low-speed and high-speed internal RC oscillators and high-speed oscillator OFF; no independent watchdog; VDD = 3.3 V; TA = 25 °C | typ 26 uA | 41 |
| Supply current in Stop mode IDD | Regulator in Low Power mode; low-speed and high-speed internal RC oscillators and high-speed oscillator OFF; no independent watchdog; TA = 85 °C | max 590 uA | 41 |
| Supply current in Stop mode IDD | Regulator in Low Power mode; low-speed and high-speed internal RC oscillators and high-speed oscillator OFF; no independent watchdog; TA = 105 °C | max 1280 uA | 41 |
| Supply current in Standby mode IDD | Low-speed internal RC oscillator and independent watchdog ON; VDD = 2.4 V; TA = 25 °C | typ 3 uA | 41 |
| Supply current in Standby mode IDD | Low-speed internal RC oscillator and independent watchdog ON; VDD = 3.3 V; TA = 25 °C | typ 3.8 uA | 41 |
| Supply current in Standby mode IDD | Low-speed internal RC oscillator ON, independent watchdog OFF; VDD = 2.4 V; TA = 25 °C | typ 2.8 uA | 41 |
| Supply current in Standby mode IDD | Low-speed internal RC oscillator ON, independent watchdog OFF; VDD = 3.3 V; TA = 25 °C | typ 3.6 uA | 41 |
| Supply current in Standby mode IDD | Low-speed internal RC oscillator, independent watchdog, low-speed oscillator and RTC OFF; VDD = 2.4 V; TA = 25 °C | typ 1.9 uA | 41 |
| Supply current in Standby mode IDD | Low-speed internal RC oscillator, independent watchdog, low-speed oscillator and RTC OFF; VDD = 3.3 V; TA = 25 °C | typ 2.1 uA | 41 |
| Supply current in Standby mode IDD | Low-speed internal RC oscillator, independent watchdog, low-speed oscillator and RTC OFF; TA = 85 °C | max 5 uA | 41 |
| Supply current in Standby mode IDD | Low-speed internal RC oscillator, independent watchdog, low-speed oscillator and RTC OFF; TA = 105 °C | max 6.5 uA | 41 |
| Backup domain supply current IDD_VBAT | Low-speed oscillator and RTC ON; VBAT = 2.0 V; TA = 25 °C | typ 1.1 uA | 41 |
| Backup domain supply current IDD_VBAT | Low-speed oscillator and RTC ON; VBAT = 2.4 V; TA = 25 °C | typ 1.2 uA | 41 |
| Backup domain supply current IDD_VBAT | Low-speed oscillator and RTC ON; VBAT = 3.3 V; TA = 25 °C | typ 1.4 uA | 41 |
| Backup domain supply current IDD_VBAT | Low-speed oscillator and RTC ON; TA = 85 °C | max 2.1 uA | 41 |
| Backup domain supply current IDD_VBAT | Low-speed oscillator and RTC ON; TA = 105 °C | max 2.3 uA | 41 |
| Supply current in Run mode IDD | External clock; fHCLK = 72 MHz; all peripherals enabled; TA = 25 °C; VDD = 3.3 V | typ 47.3 mA | 44 |
| Supply current in Run mode IDD | External clock; fHCLK = 72 MHz; all peripherals disabled; TA = 25 °C; VDD = 3.3 V | typ 28.3 mA | 44 |
| Supply current in Run mode IDD | External clock; fHCLK = 48 MHz; all peripherals enabled; TA = 25 °C; VDD = 3.3 V | typ 32 mA | 44 |
| Supply current in Run mode IDD | External clock; fHCLK = 48 MHz; all peripherals disabled; TA = 25 °C; VDD = 3.3 V | typ 19.6 mA | 44 |
| Supply current in Run mode IDD | External clock; fHCLK = 36 MHz; all peripherals enabled; TA = 25 °C; VDD = 3.3 V | typ 24.6 mA | 44 |
| Supply current in Run mode IDD | External clock; fHCLK = 36 MHz; all peripherals disabled; TA = 25 °C; VDD = 3.3 V | typ 15.4 mA | 44 |
| Supply current in Run mode IDD | External clock; fHCLK = 24 MHz; all peripherals enabled; TA = 25 °C; VDD = 3.3 V | typ 16.8 mA | 44 |
| Supply current in Run mode IDD | External clock; fHCLK = 24 MHz; all peripherals disabled; TA = 25 °C; VDD = 3.3 V | typ 10.6 mA | 44 |
| Supply current in Run mode IDD | External clock; fHCLK = 16 MHz; all peripherals enabled; TA = 25 °C; VDD = 3.3 V | typ 11.8 mA | 44 |
| Supply current in Run mode IDD | External clock; fHCLK = 16 MHz; all peripherals disabled; TA = 25 °C; VDD = 3.3 V | typ 7.4 mA | 44 |
| Supply current in Run mode IDD | External clock; fHCLK = 8 MHz; all peripherals enabled; TA = 25 °C; VDD = 3.3 V | typ 5.9 mA | 44 |
| Supply current in Run mode IDD | External clock; fHCLK = 8 MHz; all peripherals disabled; TA = 25 °C; VDD = 3.3 V | typ 3.7 mA | 44 |
| Supply current in Run mode IDD | External clock; fHCLK = 4 MHz; all peripherals enabled; TA = 25 °C; VDD = 3.3 V | typ 3.7 mA | 44 |
| Supply current in Run mode IDD | External clock; fHCLK = 4 MHz; all peripherals disabled; TA = 25 °C; VDD = 3.3 V | typ 2.9 mA | 44 |
| Supply current in Run mode IDD | External clock; fHCLK = 2 MHz; all peripherals enabled; TA = 25 °C; VDD = 3.3 V | typ 2.5 mA | 44 |
| Supply current in Run mode IDD | External clock; fHCLK = 2 MHz; all peripherals disabled; TA = 25 °C; VDD = 3.3 V | typ 2 mA | 44 |
| Supply current in Run mode IDD | External clock; fHCLK = 1 MHz; all peripherals enabled; TA = 25 °C; VDD = 3.3 V | typ 1.8 mA | 44 |
| Supply current in Run mode IDD | External clock; fHCLK = 1 MHz; all peripherals disabled; TA = 25 °C; VDD = 3.3 V | typ 1.53 mA | 44 |
| Supply current in Run mode IDD | External clock; fHCLK = 500 kHz; all peripherals enabled; TA = 25 °C; VDD = 3.3 V | typ 1.5 mA | 44 |
| Supply current in Run mode IDD | External clock; fHCLK = 500 kHz; all peripherals disabled; TA = 25 °C; VDD = 3.3 V | typ 1.3 mA | 44 |
| Supply current in Run mode IDD | External clock; fHCLK = 125 kHz; all peripherals enabled; TA = 25 °C; VDD = 3.3 V | typ 1.3 mA | 44 |
| Supply current in Run mode IDD | External clock; fHCLK = 125 kHz; all peripherals disabled; TA = 25 °C; VDD = 3.3 V | typ 1.2 mA | 44 |
| Supply current in Run mode IDD | HSI, AHB prescaler used to reduce frequency; fHCLK = 36 MHz; all peripherals enabled; TA = 25 °C; VDD = 3.3 V | typ 23.9 mA | 44 |
| Supply current in Run mode IDD | HSI, AHB prescaler used to reduce frequency; fHCLK = 36 MHz; all peripherals disabled; TA = 25 °C; VDD = 3.3 V | typ 14.8 mA | 44 |
| Supply current in Run mode IDD | HSI, AHB prescaler used to reduce frequency; fHCLK = 24 MHz; all peripherals enabled; TA = 25 °C; VDD = 3.3 V | typ 16.1 mA | 44 |
| Supply current in Run mode IDD | HSI, AHB prescaler used to reduce frequency; fHCLK = 24 MHz; all peripherals disabled; TA = 25 °C; VDD = 3.3 V | typ 9.7 mA | 44 |
| Supply current in Run mode IDD | HSI, AHB prescaler used to reduce frequency; fHCLK = 16 MHz; all peripherals enabled; TA = 25 °C; VDD = 3.3 V | typ 11.1 mA | 44 |
| Supply current in Run mode IDD | HSI, AHB prescaler used to reduce frequency; fHCLK = 16 MHz; all peripherals disabled; TA = 25 °C; VDD = 3.3 V | typ 6.7 mA | 44 |
| Supply current in Run mode IDD | HSI, AHB prescaler used to reduce frequency; fHCLK = 8 MHz; all peripherals enabled; TA = 25 °C; VDD = 3.3 V | typ 5.6 mA | 44 |
| Supply current in Run mode IDD | HSI, AHB prescaler used to reduce frequency; fHCLK = 8 MHz; all peripherals disabled; TA = 25 °C; VDD = 3.3 V | typ 3.8 mA | 44 |
| Supply current in Run mode IDD | HSI, AHB prescaler used to reduce frequency; fHCLK = 4 MHz; all peripherals enabled; TA = 25 °C; VDD = 3.3 V | typ 3.1 mA | 44 |
| Supply current in Run mode IDD | HSI, AHB prescaler used to reduce frequency; fHCLK = 4 MHz; all peripherals disabled; TA = 25 °C; VDD = 3.3 V | typ 2.1 mA | 44 |
| Supply current in Run mode IDD | HSI, AHB prescaler used to reduce frequency; fHCLK = 2 MHz; all peripherals enabled; TA = 25 °C; VDD = 3.3 V | typ 1.8 mA | 44 |
| Supply current in Run mode IDD | HSI, AHB prescaler used to reduce frequency; fHCLK = 2 MHz; all peripherals disabled; TA = 25 °C; VDD = 3.3 V | typ 1.3 mA | 44 |
| Supply current in Run mode IDD | HSI, AHB prescaler used to reduce frequency; fHCLK = 1 MHz; all peripherals enabled; TA = 25 °C; VDD = 3.3 V | typ 1.16 mA | 44 |
| Supply current in Run mode IDD | HSI, AHB prescaler used to reduce frequency; fHCLK = 1 MHz; all peripherals disabled; TA = 25 °C; VDD = 3.3 V | typ 0.9 mA | 44 |
| Supply current in Run mode IDD | HSI, AHB prescaler used to reduce frequency; fHCLK = 500 kHz; all peripherals enabled; TA = 25 °C; VDD = 3.3 V | typ 0.8 mA | 44 |
| Supply current in Run mode IDD | HSI, AHB prescaler used to reduce frequency; fHCLK = 500 kHz; all peripherals disabled; TA = 25 °C; VDD = 3.3 V | typ 0.67 mA | 44 |
| Supply current in Run mode IDD | HSI, AHB prescaler used to reduce frequency; fHCLK = 125 kHz; all peripherals enabled; TA = 25 °C; VDD = 3.3 V | typ 0.6 mA | 44 |
| Supply current in Run mode IDD | HSI, AHB prescaler used to reduce frequency; fHCLK = 125 kHz; all peripherals disabled; TA = 25 °C; VDD = 3.3 V | typ 0.5 mA | 44 |
| Thermal resistance junction-ambient ΘJA | LQFP64 - 10 × 10 mm / 0.5 mm pitch; first occurrence | typ 45 °C/W | 91 |
| Thermal resistance junction-ambient ΘJA | LQFP64 - 10 × 10 mm / 0.5 mm pitch; second occurrence | typ 45 °C/W | 91 |
| External main supply voltage (including VDDA and VDD) VDD–VSS | min -0.3 · max 4 V | 36 | |
| Input voltage on any other pin VIN | max 4 V | 36 | |
| Total current into VDD/VDDA power lines (source) IVDD | max 150 mA | 36 | |
| Total current out of VSS ground lines (sink) IVSS | max 150 mA | 36 | |
| Output current sunk by any I/O and control pin IIO | max 25 mA | 36 | |
| Output current source by any I/Os and control pin IIO | max -25 mA | 36 | |
| Storage temperature range TSTG | min -65 · max 150 °C | 37 | |
| Maximum junction temperature TJ | max 150 °C | 37 | |
| ADC sampling time when reading the internal reference voltage TS_vrefint | typ 5.1 · max 17.1 us | 39 | |
| Internal reference voltage spread over the temperature range VRERINT | VDD = 3 V ±10 mV | max 10 mV | 39 |
| Temperature coefficient TCoeff | max 100 ppm/°C | 39 | |
| Supply current in Standby mode IDD | Low-speed internal RC oscillator and independent watchdog OFF, low-speed oscillator and RTC OFF; VDD = 2.4 V; TA = 25 °C | typ 1.9 uA | 41 |
| Supply current in Standby mode IDD | Low-speed internal RC oscillator and independent watchdog OFF, low-speed oscillator and RTC OFF; VDD = 3.3 V; TA = 25 °C | typ 2.1 uA | 41 |
| Supply current in Standby mode IDD | Low-speed internal RC oscillator and independent watchdog OFF, low-speed oscillator and RTC OFF; TA = 85 °C | max 5 uA | 41 |
| Supply current in Sleep mode IDD | External clock; fHCLK = 72 MHz; all peripherals enabled; TA = 25 °C; VDD = 3.3 V | typ 28.2 mA | 45 |
| Supply current in Sleep mode IDD | External clock; fHCLK = 72 MHz; all peripherals disabled; TA = 25 °C; VDD = 3.3 V | typ 6 mA | 45 |
| Supply current in Sleep mode IDD | External clock; fHCLK = 48 MHz; all peripherals enabled; TA = 25 °C; VDD = 3.3 V | typ 19 mA | 45 |
| Supply current in Sleep mode IDD | External clock; fHCLK = 48 MHz; all peripherals disabled; TA = 25 °C; VDD = 3.3 V | typ 4.2 mA | 45 |
| Supply current in Sleep mode IDD | External clock; fHCLK = 36 MHz; all peripherals enabled; TA = 25 °C; VDD = 3.3 V | typ 14.7 mA | 45 |
| Supply current in Sleep mode IDD | External clock; fHCLK = 36 MHz; all peripherals disabled; TA = 25 °C; VDD = 3.3 V | typ 3.4 mA | 45 |
| Supply current in Sleep mode IDD | External clock; fHCLK = 24 MHz; all peripherals enabled; TA = 25 °C; VDD = 3.3 V | typ 10.1 mA | 45 |
| Supply current in Sleep mode IDD | External clock; fHCLK = 24 MHz; all peripherals disabled; TA = 25 °C; VDD = 3.3 V | typ 2.5 mA | 45 |
| Supply current in Sleep mode IDD | External clock; fHCLK = 16 MHz; all peripherals enabled; TA = 25 °C; VDD = 3.3 V | typ 6.7 mA | 45 |
| Supply current in Sleep mode IDD | External clock; fHCLK = 16 MHz; all peripherals disabled; TA = 25 °C; VDD = 3.3 V | typ 2 mA | 45 |
| Supply current in Sleep mode IDD | External clock; fHCLK = 8 MHz; all peripherals enabled; TA = 25 °C; VDD = 3.3 V | typ 3.2 mA | 45 |
| Supply current in Sleep mode IDD | External clock; fHCLK = 8 MHz; all peripherals disabled; TA = 25 °C; VDD = 3.3 V | typ 1.3 mA | 45 |
| Supply current in Sleep mode IDD | External clock; fHCLK = 4 MHz; all peripherals enabled; TA = 25 °C; VDD = 3.3 V | typ 2.3 mA | 45 |
| Supply current in Sleep mode IDD | External clock; fHCLK = 4 MHz; all peripherals disabled; TA = 25 °C; VDD = 3.3 V | typ 1.2 mA | 45 |
| Supply current in Sleep mode IDD | External clock; fHCLK = 2 MHz; all peripherals enabled; TA = 25 °C; VDD = 3.3 V | typ 1.7 mA | 45 |
| Supply current in Sleep mode IDD | External clock; fHCLK = 2 MHz; all peripherals disabled; TA = 25 °C; VDD = 3.3 V | typ 1.16 mA | 45 |
| Supply current in Sleep mode IDD | External clock; fHCLK = 1 MHz; all peripherals enabled; TA = 25 °C; VDD = 3.3 V | typ 1.5 mA | 45 |
| Supply current in Sleep mode IDD | External clock; fHCLK = 1 MHz; all peripherals disabled; TA = 25 °C; VDD = 3.3 V | typ 1.1 mA | 45 |
| Supply current in Sleep mode IDD | External clock; fHCLK = 500 kHz; all peripherals enabled; TA = 25 °C; VDD = 3.3 V | typ 1.3 mA | 45 |
| Supply current in Sleep mode IDD | External clock; fHCLK = 500 kHz; all peripherals disabled; TA = 25 °C; VDD = 3.3 V | typ 1.05 mA | 45 |
| Supply current in Sleep mode IDD | External clock; fHCLK = 125 kHz; all peripherals enabled; TA = 25 °C; VDD = 3.3 V | typ 1.2 mA | 45 |
| Supply current in Sleep mode IDD | External clock; fHCLK = 125 kHz; all peripherals disabled; TA = 25 °C; VDD = 3.3 V | typ 1.05 mA | 45 |
| Supply current in Sleep mode IDD | HSI, AHB prescaler used to reduce frequency; fHCLK = 36 MHz; all peripherals enabled; TA = 25 °C; VDD = 3.3 V | typ 13.7 mA | 45 |
| Supply current in Sleep mode IDD | HSI, AHB prescaler used to reduce frequency; fHCLK = 36 MHz; all peripherals disabled; TA = 25 °C; VDD = 3.3 V | typ 2.6 mA | 45 |
| Supply current in Sleep mode IDD | HSI, AHB prescaler used to reduce frequency; fHCLK = 24 MHz; all peripherals enabled; TA = 25 °C; VDD = 3.3 V | typ 9.3 mA | 45 |
| Supply current in Sleep mode IDD | HSI, AHB prescaler used to reduce frequency; fHCLK = 24 MHz; all peripherals disabled; TA = 25 °C; VDD = 3.3 V | typ 1.8 mA | 45 |
| Supply current in Sleep mode IDD | HSI, AHB prescaler used to reduce frequency; fHCLK = 16 MHz; all peripherals enabled; TA = 25 °C; VDD = 3.3 V | typ 6.3 mA | 45 |
| Supply current in Sleep mode IDD | HSI, AHB prescaler used to reduce frequency; fHCLK = 16 MHz; all peripherals disabled; TA = 25 °C; VDD = 3.3 V | typ 1.3 mA | 45 |
| Supply current in Sleep mode IDD | HSI, AHB prescaler used to reduce frequency; fHCLK = 8 MHz; all peripherals enabled; TA = 25 °C; VDD = 3.3 V | typ 2.7 mA | 45 |
| Supply current in Sleep mode IDD | HSI, AHB prescaler used to reduce frequency; fHCLK = 8 MHz; all peripherals disabled; TA = 25 °C; VDD = 3.3 V | typ 0.6 mA | 45 |
| Supply current in Sleep mode IDD | HSI, AHB prescaler used to reduce frequency; fHCLK = 4 MHz; all peripherals enabled; TA = 25 °C; VDD = 3.3 V | typ 1.6 mA | 45 |
| Supply current in Sleep mode IDD | HSI, AHB prescaler used to reduce frequency; fHCLK = 4 MHz; all peripherals disabled; TA = 25 °C; VDD = 3.3 V | typ 0.5 mA | 45 |
| Supply current in Sleep mode IDD | HSI, AHB prescaler used to reduce frequency; fHCLK = 2 MHz; all peripherals enabled; TA = 25 °C; VDD = 3.3 V | typ 1 mA | 45 |
| Supply current in Sleep mode IDD | HSI, AHB prescaler used to reduce frequency; fHCLK = 2 MHz; all peripherals disabled; TA = 25 °C; VDD = 3.3 V | typ 0.46 mA | 45 |
| Supply current in Sleep mode IDD | HSI, AHB prescaler used to reduce frequency; fHCLK = 1 MHz; all peripherals enabled; TA = 25 °C; VDD = 3.3 V | typ 0.8 mA | 45 |
| Supply current in Sleep mode IDD | HSI, AHB prescaler used to reduce frequency; fHCLK = 1 MHz; all peripherals disabled; TA = 25 °C; VDD = 3.3 V | typ 0.44 mA | 45 |
| Supply current in Sleep mode IDD | HSI, AHB prescaler used to reduce frequency; fHCLK = 500 kHz; all peripherals enabled; TA = 25 °C; VDD = 3.3 V | typ 0.6 mA | 45 |
| Supply current in Sleep mode IDD | HSI, AHB prescaler used to reduce frequency; fHCLK = 500 kHz; all peripherals disabled; TA = 25 °C; VDD = 3.3 V | typ 0.43 mA | 45 |
| Supply current in Sleep mode IDD | HSI, AHB prescaler used to reduce frequency; fHCLK = 125 kHz; all peripherals enabled; TA = 25 °C; VDD = 3.3 V | typ 0.5 mA | 45 |
| Supply current in Sleep mode IDD | HSI, AHB prescaler used to reduce frequency; fHCLK = 125 kHz; all peripherals disabled; TA = 25 °C; VDD = 3.3 V | typ 0.42 mA | 45 |
| APB2-Bridge | APB2 (up to 72 MHz); 25 °C | typ 3.47 uA/MHz | 47 |
| GPIOA | APB2 (up to 72 MHz); 25 °C | typ 6.39 uA/MHz | 47 |
| GPIOB | APB2 (up to 72 MHz); 25 °C | typ 6.39 uA/MHz | 47 |
| GPIOC | APB2 (up to 72 MHz); 25 °C | typ 6.11 uA/MHz | 47 |
| GPIOD | APB2 (up to 72 MHz); 25 °C | typ 6.39 uA/MHz | 47 |
| GPIOE | APB2 (up to 72 MHz); 25 °C | typ 6.11 uA/MHz | 47 |
| SPI1 | APB2 (up to 72 MHz); 25 °C | typ 3.61 uA/MHz | 47 |
| USART1 | APB2 (up to 72 MHz); 25 °C | typ 12.08 uA/MHz | 47 |
| TIM1 | APB2 (up to 72 MHz); 25 °C | typ 23.47 uA/MHz | 47 |
| ADC1 | 25 °C; fHCLK = 56 MHz; fAPB1 = fHCLK/2; fAPB2 = fHCLK; fADCCLK = fAPB2/4; add 0.6 mA analog current when ADON = 1 | typ 18.21 uA/MHz | 47 |
| External user clock source frequency fHSE_ext | min 1 · typ 8 · max 50 MHz | 47 | |
| OSC_IN high or low time tw(HSE) | min 5 ns | 47 | |
| OSC_IN rise or fall time tr(HSE), tf(HSE) | max 20 ns | 47 | |
| OSC_IN input capacitance Cin(HSE) | typ 5 pF | 47 | |
| Duty cycle DuCy(HSE) | min 45 · max 55 % | 47 | |
| Oscillator frequency fOSC_IN | min 3 · max 25 MHz | 49 | |
| Feedback resistor RF | typ 200 kΩ | 49 | |
| Recommended load capacitance versus equivalent serial resistance of the crystal (RS) C | RS = 30 Ω | typ 30 pF | 49 |
| HSE driving current i2 | VDD = 3.3 V, VIN = VSS with 30 pF load | max 1 mA | 49 |
| Oscillator transconductance gm | Startup | min 25 mA/V | 49 |
| Startup time tSU(HSE) | VDD is stabilized | typ 2 ms | 49 |
| Feedback resistor RF | typ 5 MΩ | 50 | |
| Recommended load capacitance versus equivalent serial resistance of the crystal (RS) C | RS = 30 kΩ | max 15 pF | 50 |
| LSE driving current I2 | VDD = 3.3 V, VIN = VSS | max 1.4 uA | 50 |
| Oscillator Transconductance gm | min 5 uA/V | 50 | |
| Startup time tSU(LSE) | VDD is stabilized; TA = 50 °C | typ 1.5 s | 51 |
| Startup time tSU(LSE) | VDD is stabilized; TA = 25 °C | typ 2.5 s | 51 |
| Startup time tSU(LSE) | VDD is stabilized; TA = 10 °C | typ 4 s | 51 |
| Startup time tSU(LSE) | VDD is stabilized; TA = 0 °C | typ 6 s | 51 |
| Startup time tSU(LSE) | VDD is stabilized; TA = -10 °C | typ 10 s | 51 |
| Startup time tSU(LSE) | VDD is stabilized; TA = -20 °C | typ 17 s | 51 |
| Startup time tSU(LSE) | VDD is stabilized; TA = -30 °C | typ 32 s | 51 |
| Startup time tSU(LSE) | VDD is stabilized; TA = -40 °C | typ 60 s | 51 |
| Frequency fHSI | VDD = 3.3 V, TA = –40 to 105 °C | typ 8 MHz | 52 |
| Duty cycle DuCy(HSI) | VDD = 3.3 V, TA = –40 to 105 °C | min 45 · max 55 % | 52 |
| Accuracy of the HSI oscillator ACCHSI | User-trimmed with the RCC_CR register; guaranteed by design | max 1 % | 52 |
| Accuracy of the HSI oscillator ACCHSI | Factory-calibrated; TA = –40 to 105 °C | min -2 · max 2.5 % | 52 |
| Accuracy of the HSI oscillator ACCHSI | Factory-calibrated; TA = 0 to 70 °C | min -1.3 · max 2 % | 52 |
| Accuracy of the HSI oscillator ACCHSI | Factory-calibrated; TA = 25 °C | min -1.1 · max 1.8 % | 52 |
| HSI oscillator startup time tsu(HSI) | VDD = 3.3 V, TA = –40 to 105 °C | min 1 · max 2 us | 52 |
| HSI oscillator power consumption IDD(HSI) | VDD = 3.3 V, TA = –40 to 105 °C | typ 80 · max 100 uA | 52 |
| Frequency fLSI | VDD = 3 V, TA = –40 to 105 °C | min 30 · typ 40 · max 60 kHz | 52 |
| LSI oscillator startup time tsu(LSI) | VDD = 3 V, TA = –40 to 105 °C | max 85 us | 52 |
| LSI oscillator power consumption IDD(LSI) | VDD = 3 V, TA = –40 to 105 °C | typ 0.65 · max 1.2 uA | 52 |
| 16-bit programming time tprog | TA = –40 to +105 °C | min 40 · typ 52.5 · max 70 us | 54 |
| Page (1 KB) erase time tERASE | TA = –40 to +105 °C | min 20 · max 40 ms | 54 |
| Mass erase time tME | TA = –40 to +105 °C | min 20 · max 40 ms | 54 |
| Supply current IDD | Read mode; fHCLK = 72 MHz with 2 wait states, VDD = 3.3 V | max 20 mA | 54 |
| Supply current IDD | Write / Erase modes; fHCLK = 72 MHz, VDD = 3.3 V | max 5 mA | 54 |
| Supply current IDD | Power-down mode / Halt; VDD = 3.0 to 3.6 V | max 50 uA | 54 |
| Programming voltage Vprog | min 2 · max 3.6 V | 54 | |
| Endurance NEND | TA = –40 to +85 °C (6 suffix versions) | min 10 Kcycles | 54 |
| Data retention tRET | 1 kcycle at TA = 85 °C | min 30 Years | 54 |
| Data retention tRET | 1 kcycle at TA = 105 °C | min 10 Years | 54 |
| Data retention tRET | 10 kcycles at TA = 55 °C | min 20 Years | 54 |
| Electrostatic discharge voltage (human body model) VESD(HBM) | TA = +25 °C conforming to JESD22-A114; Class 2 | max 2000 V | 56 |
| Electrostatic discharge voltage (charge device model) VESD(CDM) | TA = +25 °C conforming to JESD22-C101; Class II | max 500 V | 56 |
| Output low level voltage for an I/O pin when 8 pins are sunk at same time VOL | TTL port; IIO = +8 mA; 2.7 V < VDD < 3.6 V | max 0.4 V | 60 |
| Output low level voltage for an I/O pin when 8 pins are sunk at same time VOL | CMOS port; IIO = +8 mA; 2.7 V < VDD < 3.6 V | max 0.4 V | 60 |
| Output high level voltage for an I/O pin when 8 pins are sourced at same time VOH | CMOS port; IIO = +8 mA; 2.7 V < VDD < 3.6 V | min 2.4 V | 60 |
| Output low level voltage for an I/O pin when 8 pins are sunk at same time VOL | IIO = +20 mA; 2.7 V < VDD < 3.6 V | max 1.3 V | 60 |
| Output low level voltage for an I/O pin when 8 pins are sunk at same time VOL | IIO = +6 mA; 2 V < VDD < 2.7 V | max 0.4 V | 60 |
| Maximum frequency fmax(IO)out | MODEx[1:0] = 10; CL = 50 pF, VDD = 2 V to 3.6 V | max 2 MHz | 61 |
| Output high to low level fall time tf(IO)out | MODEx[1:0] = 10; CL = 50 pF, VDD = 2 V to 3.6 V | max 125 ns | 61 |
| Output low to high level rise time tr(IO)out | MODEx[1:0] = 10; CL = 50 pF, VDD = 2 V to 3.6 V | max 125 ns | 61 |
| Maximum frequency fmax(IO)out | MODEx[1:0] = 01; CL = 50 pF, VDD = 2 V to 3.6 V | max 10 MHz | 61 |
| Output high to low level fall time tf(IO)out | MODEx[1:0] = 01; CL = 50 pF, VDD = 2 V to 3.6 V | max 25 ns | 61 |
| Output low to high level rise time tr(IO)out | MODEx[1:0] = 01; CL = 50 pF, VDD = 2 V to 3.6 V | max 25 ns | 61 |
| Maximum frequency Fmax(IO)out | MODEx[1:0] = 11; CL = 30 pF, VDD = 2.7 V to 3.6 V | max 50 MHz | 61 |
| Maximum frequency Fmax(IO)out | MODEx[1:0] = 11; CL = 50 pF, VDD = 2.7 V to 3.6 V | max 30 MHz | 61 |
| Maximum frequency Fmax(IO)out | MODEx[1:0] = 11; CL = 50 pF, VDD = 2 V to 2.7 V | max 20 MHz | 61 |
| Output high to low level fall time tf(IO)out | MODEx[1:0] = 11; CL = 30 pF, VDD = 2.7 V to 3.6 V | max 5 ns | 61 |
| Output high to low level fall time tf(IO)out | MODEx[1:0] = 11; CL = 50 pF, VDD = 2.7 V to 3.6 V | max 8 ns | 61 |
| Output high to low level fall time tf(IO)out | MODEx[1:0] = 11; CL = 50 pF, VDD = 2 V to 2.7 V | max 12 ns | 61 |
| Output low to high level rise time tr(IO)out | MODEx[1:0] = 11; CL = 30 pF, VDD = 2.7 V to 3.6 V | max 5 ns | 61 |
| Output low to high level rise time tr(IO)out | MODEx[1:0] = 11; CL = 50 pF, VDD = 2.7 V to 3.6 V | max 8 ns | 61 |
| Output low to high level rise time tr(IO)out | MODEx[1:0] = 11; CL = 50 pF, VDD = 2 V to 2.7 V | max 12 ns | 61 |
| Pulse width of external signals detected by the EXTI controller tEXTIpw | min 10 ns | 61 | |
| USB OTG FS transceiver startup time tSTARTUP | Guaranteed by design | max 1 us | 71 |
| USB OTG FS operating voltage VDD | min 3 · max 3.6 V | 71 | |
| Differential input sensitivity VDI | I(USBDP, USBDM) | min 0.2 V | 71 |
| Differential common mode range VCM | Includes VDI range | min 0.8 · max 2.5 V | 71 |
| Single ended receiver threshold VSE | min 1.3 · max 2 V | 71 | |
| Static output level low VOL | RL of 1.5 kΩ to 3.6 V | max 0.3 V | 71 |
| Static output level high VOH | RL of 15 kΩ to VSS | min 2.8 · max 3.6 V | 71 |
| Pull-down resistance on PA11, PA12 RPD | VIN = VDD | min 17 · typ 21 · max 24 kΩ | 71 |
| Pull-down resistance on PA9 RPD | VIN = VDD | min 0.65 · typ 1.1 · max 2 kΩ | 71 |
| Pull-up resistance on PA12 RPU | VIN = VSS | min 1.5 · typ 1.8 · max 2.1 kΩ | 71 |
| Pull-up resistance on PA9 RPU | VIN = VSS | min 0.25 · typ 0.37 · max 0.55 kΩ | 71 |
| Rise time tr | CL = 50 pF | min 4 · max 20 ns | 72 |
| Fall time tf | CL = 50 pF | min 4 · max 20 ns | 72 |
| Rise/ fall time matching trfm | tr/tf | min 90 · max 110 % | 72 |
| Output signal crossover voltage VCRS | min 1.3 · max 2 V | 72 | |
| Power supply VDDA | min 2.4 · max 3.6 V | 74 | |
| Positive reference voltage VREF+ | VREF+ is internally connected to VDDA | min 2.4 V | 74 |
| Current on the VREF input pin IVREF | typ 160 · max 220 uA | 74 | |
| ADC clock frequency fADC | min 0.6 · max 14 MHz | 74 | |
| Sampling rate fS | min 0.05 · max 1 MHz | 74 | |
| External trigger frequency fTRIG | fADC = 14 MHz | max 823 kHz | 74 |
| External trigger frequency fTRIG | max 17 1/fADC | 74 | |
| External input impedance RAIN | See Equation 1 and Table 53 for details | max 50 kΩ | 74 |
| Sampling switch resistance RADC | max 1 kΩ | 74 | |
| Internal sample and hold capacitor CADC | max 8 pF | 74 | |
| Calibration time tCAL | fADC = 14 MHz | typ 5.9 us | 74 |
| Calibration time tCAL | typ 83 1/fADC | 74 | |
| Injection trigger conversion latency tlat | fADC = 14 MHz; external triggers require an additional delay of 1/fPCLK2 | max 0.214 us | 75 |
| Injection trigger conversion latency tlat | External triggers require an additional delay of 1/fPCLK2 | max 3 1/fADC | 75 |
| Regular trigger conversion latency tlatr | fADC = 14 MHz; external triggers require an additional delay of 1/fPCLK2 | max 0.143 us | 75 |
| Regular trigger conversion latency tlatr | External triggers require an additional delay of 1/fPCLK2 | max 2 1/fADC | 75 |
| Sampling time tS | fADC = 14 MHz | min 0.107 · max 17.1 us | 75 |
| Sampling time tS | min 1.5 · max 239.5 1/fADC | 75 | |
| Power-up time tSTAB | min 0 · typ 0 · max 1 us | 75 | |
| Total conversion time (including sampling time) tCONV | fADC = 14 MHz | min 1 · max 18 us | 75 |
| Total conversion time (including sampling time) tCONV | tS for sampling +12.5 for successive approximation | min 14 · max 252 1/fADC | 75 |
| RAIN max RAIN | Ts = 1.5 cycles; tS = 0.11 us | max 0.4 kΩ | 75 |
| RAIN max RAIN | Ts = 7.5 cycles; tS = 0.54 us | max 5.9 kΩ | 75 |
| RAIN max RAIN | Ts = 13.5 cycles; tS = 0.96 us | max 11.4 kΩ | 75 |
| RAIN max RAIN | Ts = 28.5 cycles; tS = 2.04 us | max 25.2 kΩ | 75 |
| RAIN max RAIN | Ts = 41.5 cycles; tS = 2.96 us | max 37.2 kΩ | 75 |
| RAIN max RAIN | Ts = 55.5 cycles; tS = 3.96 us | max 50 kΩ | 75 |
| Analog supply voltage VDDA | min 2.4 · max 3.6 V | 79 | |
| Reference supply voltage VREF+ | VREF+ must always be below VDDA | min 2.4 · max 3.6 V | 79 |
| Ground VSSA | min 0 · max 0 V | 79 | |
| Resistive load with buffer ON RLOAD | min 5 kΩ | 79 | |
| Impedance output with buffer OFF RO | When buffer is OFF, minimum resistive load between DAC_OUT and VSS for 1% accuracy is 1.5 MΩ | max 15 kΩ | 79 |
| Capacitive load CLOAD | DAC_OUT pin, buffer ON | max 50 pF | 79 |
| Lower DAC_OUT voltage with buffer ON DAC_OUT min | min 0.2 V | 79 | |
| Lower DAC_OUT voltage with buffer OFF DAC_OUT min | typ 0.5 mV | 79 | |
| DAC DC current consumption in quiescent mode (Standby mode) IDDVREF+ | No load, worst code (0xF1C) at VREF+ = 3.6 V | max 220 uA | 79 |
| DAC DC current consumption in quiescent mode (Standby mode) IDDA | No load, middle code (0x800) on the inputs | max 380 uA | 79 |
| DAC DC current consumption in quiescent mode (Standby mode) IDDA | No load, worst code (0xF1C) at VREF+ = 3.6 V | max 480 uA | 79 |
| Thermal resistance junction-ambient ΘJA | LQFP64 - 10 × 10 mm / 0.5 mm pitch | typ 45 °C/W | 91 |
| Supply current in run mode IDD | VDD = 3.3 V; external clock, all peripherals enabled except ethernet, HSE = 8 MHz, fHCLK = 72 MHz, no MCO; maximum at 85 °C | typ 57 · max 63 mA | 102 |
| Supply current in run mode IDD | VDD = 3.3 V; external clock, all peripherals enabled except ethernet, HSE = 14.74 MHz, fHCLK = 72 MHz, no MCO; maximum at 85 °C | typ 60.5 · max 67 mA | 102 |
| Supply current in run mode IDD | VDD = 3.3 V; external clock, only OTG enabled, HSE = 8 MHz, fHCLK = 48 MHz, no MCO | typ 26.7 mA | 102 |

silvervest/OpenFlops-W1D
Modified OpenFlops specifically to replace Citizen W1D drives

hmerrett/HenryFlops
OpenFlops is an Open Hardware implementation of such an emulator, inspired from the ubiquitous Gotek hardware. It is designed to run the FlashFloppy firmware, which gives it several improvements over the original Gotek…

stefanskotte/Nano-Tek
A tiny, modern reimagining of the classic Gotek floppy-disk-drive emulator. Nano-Tek keeps the full feature set of a Gotek-style FDD emulator but packs it onto a board that is a fraction of the size, hence the name…

MikolajDIY/ForZero
Sterownik fizycznego zestawu wskaźników Audi A4 B6, pozwalający wyświetlać telemetrię z Forza Horizon 6 przy użyciu STM32, CAN, USB i autorskiej aplikacji Qt.

myriadrf/reference-development-kit
The Myriad-RF Reference Hardware design files and firmware

zartarn15/hubble-metal-detector
STM32-based digital metal detector with custom hardware and embedded DSP firmware.
Yes. The symbol is MCU_ST_STM32F1:STM32F105RBTx and the footprint Package_QFP:LQFP-64_10x10mm_P0.5mm, both drawn on this page. PCBKit places them on a board for you when you design with it.
LQFP-64(10x10), with 64 pins. Its footprint is drawn on this page.
STMicroelectronics publishes it: the Datasheet link on this page opens it.
JLCPCB lists it as part C8349, with 3,735 in stock; the sellers' links on this page open their listings.
Parts like it in the library: the STM32F103RCT6 by STMicroelectronics, the MSPM0G3507SPMR by Texas Instruments, the GD32F103RBT6 by GigaDevice and the GD32F103RCT6 by GigaDevice. Check their datasheets: a part that fits the footprint may still differ in its ratings.
6 boards in 6 repositories on GitHub; the most starred are listed on this page, with their KiCad files.