Skip to the content

STM32F103RBT6

STMicroelectronicsExtended

-40℃~+85℃ 128KB 12bit 20KB 2V~3.6V 32 Bit 51 72MHz ARM Cortex-M3 Built-in FLASH LQFP-64(10x10) Microcontrollers (MCU/MPU/SOC) ROHS

Part id
st/STM32F103RBT6
Category
Microcontrollers (MCU, MPU, SOC)
Package
LQFP-64(10x10)
Pins
64
In stock
7,284 at JLCPCB (C8735)
Used on
10 open-source boards

Overview

The STM32F103RBT6 is a microcontroller made by STMicroelectronics in a LQFP-64(10x10) package with 64 pins. -40℃~+85℃ 128KB 12bit 20KB 2V~3.6V 32 Bit 51 72MHz ARM Cortex-M3 Built-in FLASH LQFP-64(10x10) Microcontrollers (MCU/MPU/SOC) ROHS.

PCBKit's library has its KiCad symbol (MCU_ST_STM32F1:STM32F103RBTx, from KiCad's library) and its footprint (Package_QFP:LQFP-64_10x10mm_P0.5mm, from KiCad's library), ready for a KiCad board. 7,284 are in stock at JLCPCB (part C8735). 10 open-source boards in 10 repositories on GitHub use it.

Symbol

1VBAT2PC133PC144PC155PD06PD17NRST8PC09PC110PC211PC312VSSA13VDDA14PA015PA116PA217PA318VSS19VDD20PA421PA522PA623PA724PC425PC526PB027PB128PB229PB1030PB1132VDD33PB1234PB1335PB1436PB1537PC638PC739PC840PC941PA842PA943PA1044PA1145PA1246PA1348VDD49PA1450PA1551PC1052PC1153PC1254PD255PB356PB457PB558PB659PB760BOOT061PB862PB964VDD
MCU_ST_STM32F1:STM32F103RBTxFrom KiCad's library

Footprint

Package_QFP:LQFP-64_10x10mm_P0.5mmFrom KiCad's library

From the datasheet

19
Supply, least
2 V · VDD, recommended operating min · p. 38
Supply, most
3.6 V · VDD, recommended operating max · p. 38
Supply, least
2.4 V · VDDA, ADC used, recommended operating min · p. 38
Supply, least
1.8 V · VBAT, recommended operating min · p. 38
Supply, absolute maximum
4 V · VDD and VDDA, absolute max · p. 37
Works from
-40 °C · Ambient, suffix 6, maximum power dissipation, min · p. 38
Works up to
85 °C · Ambient, suffix 6, maximum power dissipation, max · p. 38
Works up to
105 °C · Ambient, suffix 6, low-power dissipation, max subject to junction limit · p. 38
Junction, hottest
105 °C · Junction, suffix 6, operating max · p. 38
Junction, hottest
150 °C · Junction, absolute max · p. 37
Takes working
36 mA · VDD, typical Run at 72 MHz, Flash, peripherals enabled, 3.3 V, 25 °C; ADC analog current additional · p. 47
Takes at most
50 mA · VDD, max Run at 72 MHz, Flash, peripherals enabled, 85 °C · p. 41
Takes asleep
2 µA · VDD, typical Standby, RC and watchdog off, RTC off, 3.3 V, 25 °C · p. 44
A pin gives at most
25 mA · I/O or control pin, absolute max sink current · p. 37
Junction to air (LQFP64)
45 K/W · Junction to ambient thermal resistance · p. 104
Takes at most
50.3 mA · VDD, max Run mode, Flash, 72 MHz, external clock, all peripherals enabled, TA = 105 °C · p. 41
Supply, least
3 V · VDD, USB electrical compliance min · p. 73
A pin gives at most
20 mA · GPIO source or sink max, relaxed VOL/VOH; excludes PC13–PC15 · p. 64
A pin gives at most
3 mA · PC13, PC14 and PC15 source or sink max · p. 64

What it is and has

28
CPU core
Arm 32-bit Cortex-M3 · p. 1
CPU maximum frequency
72 MHz · p. 1
CPU performance
1.25 DMIPS/MHz (Dhrystone 2.1) · p. 1
Flash memory
128 Kbytes · p. 107
SRAM
20 Kbytes · p. 1
General-purpose timers
3 · p. 10
Advanced-control timers
1 · p. 10
SPI
2 · p. 10
I2C
2 · p. 10
USART
3 · p. 10
USB
1 · p. 10
CAN
1 · p. 10
GPIOs
51 · p. 10
ADC
2 synchronized 12-bit ADCs · p. 10
ADC channels
16 · p. 10
DMA
7-channel controller · p. 1
Low-power modes
Sleep, Stop and Standby · p. 1
Temperature sensor
Integrated · p. 1
CRC and unique ID
CRC calculation unit, 96-bit unique ID · p. 1
CAN protocol
2.0B Active · p. 1
USB protocol
USB 2.0 full-speed · p. 1
Package
LQFP64, 10 × 10 mm · p. 1
Maximum CPU frequency
72 MHz · p. 1
Timers
7 · p. 1
Interfaces and converters
USB, CAN, 2 ADCs, 9 communication interfaces · p. 1
CPU arithmetic
Single-cycle multiplication and hardware division · p. 1
Debug interfaces
SWD and JTAG · p. 1
ADC
12-bit · p. 74

Around it

9
cap 100 nF
between VDD and VSS; Power-supply scheme shows one capacitor at each VDD/VSS supply pair. · p. 36
cap 4.7 µF
between VDD3 and VSS; Must be connected to VDD3. · p. 36
crystal 4 to 16 MHz
between OSC_IN and OSC_OUT; Crystal or ceramic resonator for HSE; place the resonator and load capacitors close to the oscillator pins. · p. 52
cap 5 pF to 25 pF
between OSC_IN and GND; CL1; high-quality ceramic for high-frequency applications, selected to match the crystal or resonator; include PCB and pin capacitance. · p. 53
crystal 8 MHz
between OSC_IN and OSC_OUT; Typical application; REXT depends on crystal characteristics. · p. 53
crystal 32.768 kHz
between OSC32_IN and OSC32_OUT; LSE crystal or ceramic resonator; place it and its load capacitors close to the oscillator pins. · p. 53
cap 5 to 15 pF
between OSC32_IN and GND; CL1; high-quality ceramic matched to the resonator. Recommended resonator load capacitance CL ≤ 7 pF; do not use a 12.5 pF load-capacitance resonator. · p. 54
cap 8 pF
between OSC32_IN and GND; Example CL1 with resonator CL = 6 pF and Cstray = 2 pF. · p. 54
res 1.5 kΩ
between USBDP and 3.0 to 3.6 V; D+ pull-up required for USB 2.0 full-speed electrical compliance. · p. 73

Specifications

420
ParameterConditionsAs printedPage
External main supply voltage (including VDDA and VDD) VDD − VSSAbsolute maximummin -0.3 · max 4 V37
Input voltage on any other pin VINAbsolute maximummax 4 V37
Variations between different VDD power pins |ΔVDDx|Absolute maximummax 50 mV37
Variations between all the different ground pins |VSSX − VSS|Absolute maximummax 50 mV37
Total current into VDD/VDDA power lines (source) IVDDAbsolute maximummax 150 mA37
Total current out of VSS ground lines (sink) IVSSAbsolute maximummax 150 mA37
Output current sunk by any I/O and control pin IIOAbsolute maximummax 25 mA37
Output current source by any I/Os and control pin IIOAbsolute maximummax -25 mA37
Storage temperature range TSTGAbsolute maximummin -65 · max 150 °C37
Maximum junction temperature TJAbsolute maximummax 150 °C37
Internal AHB clock frequency fHCLKmin 0 · max 72 MHz38
Internal APB1 clock frequency fPCLK1min 0 · max 36 MHz38
Internal APB2 clock frequency fPCLK2min 0 · max 72 MHz38
Standard operating voltage VDDmin 2 · max 3.6 V38
Analog operating voltage (ADC not used) VDDAMust be the same potential as VDDmin 2 · max 3.6 V38
Analog operating voltage (ADC used) VDDAMust be the same potential as VDDmin 2.4 · max 3.6 V38
Backup operating voltage VBATmin 1.8 · max 3.6 V38
I/O input voltage VINStandard IOmin -0.3 V38
I/O input voltage VINFT IO; 2 V < VDD ≤ 3.6 V; internal pull-up/pull-down disabled above VDD + 0.3 Vmin -0.3 · max 5.5 V38
I/O input voltage VINFT IO; VDD = 2 V; internal pull-up/pull-down disabled above VDD + 0.3 Vmin -0.3 · max 5.2 V38
I/O input voltage VINBOOT0min 0 · max 5.5 V38
Power dissipation at TA = 85 °C for suffix 6 or TA = 105 °C for suffix 7 PDLQFP64; suffix 6; TA = 85 °Cmax 444 mW38
Ambient temperature for 6 suffix version TAMaximum power dissipationmin -40 · max 85 °C38
Ambient temperature for 6 suffix version TALow-power dissipation; TJ must not exceed TJmaxmin -40 · max 105 °C38
Junction temperature range TJ6 suffix versionmin -40 · max 105 °C38
VDD rise time rate tVDDSubject to general operating conditions for TAmin 0 us/V39
VDD fall time rate tVDDSubject to general operating conditions for TAmin 20 us/V39
Programmable voltage detector level selection VPVDPLS[2:0] = 000 (rising edge)min 2.1 · typ 2.18 · max 2.26 V39
Programmable voltage detector level selection VPVDPLS[2:0] = 000 (falling edge)min 2 · typ 2.08 · max 2.16 V39
Programmable voltage detector level selection VPVDPLS[2:0] = 001 (rising edge)min 2.19 · typ 2.28 · max 2.37 V39
Programmable voltage detector level selection VPVDPLS[2:0] = 001 (falling edge)min 2.09 · typ 2.18 · max 2.27 V39
Programmable voltage detector level selection VPVDPLS[2:0] = 010 (rising edge)min 2.28 · typ 2.38 · max 2.48 V39
Programmable voltage detector level selection VPVDPLS[2:0] = 010 (falling edge)min 2.18 · typ 2.28 · max 2.38 V39
Programmable voltage detector level selection VPVDPLS[2:0] = 011 (rising edge)min 2.38 · typ 2.48 · max 2.58 V39
Programmable voltage detector level selection VPVDPLS[2:0] = 011 (falling edge)min 2.28 · typ 2.38 · max 2.48 V39
Programmable voltage detector level selection VPVDPLS[2:0] = 100 (rising edge)min 2.47 · typ 2.58 · max 2.69 V39
Programmable voltage detector level selection VPVDPLS[2:0] = 100 (falling edge)min 2.37 · typ 2.48 · max 2.59 V39
Programmable voltage detector level selection VPVDPLS[2:0] = 101 (rising edge)min 2.57 · typ 2.68 · max 2.79 V39
Programmable voltage detector level selection VPVDPLS[2:0] = 101 (falling edge)min 2.47 · typ 2.58 · max 2.69 V39
Programmable voltage detector level selection VPVDPLS[2:0] = 110 (rising edge)min 2.66 · typ 2.78 · max 2.9 V39
Programmable voltage detector level selection VPVDPLS[2:0] = 110 (falling edge)min 2.56 · typ 2.68 · max 2.8 V39
Programmable voltage detector level selection VPVDPLS[2:0] = 111 (rising edge)min 2.76 · typ 2.88 · max 3 V39
Programmable voltage detector level selection VPVDPLS[2:0] = 111 (falling edge)min 2.66 · typ 2.78 · max 2.9 V39
PVD hysteresis VPVDhystSpecified by design, not tested in productiontyp 100 mV39
Power on/power down reset threshold VPOR/PDRFalling edgemin 1.8 · typ 1.88 · max 1.96 V39
Power on/power down reset threshold VPOR/PDRRising edgemin 1.84 · typ 1.92 · max 2 V39
PDR hysteresis VPDRhystSpecified by design, not tested in productiontyp 40 mV39
Reset temporization TRSTTEMPOSpecified by design, not tested in productionmin 1 · typ 2.5 · max 4.5 ms39
Internal reference voltage VREFINT–40 °C < TA < +105 °Cmin 1.16 · typ 1.2 · max 1.26 V40
Internal reference voltage VREFINT–40 °C < TA < +85 °Cmin 1.16 · typ 1.2 · max 1.24 V40
ADC sampling time when reading the internal reference voltage TS_vrefintShortest sampling time can be determined in the application by multiple iterationstyp 5.1 · max 17.1 us40
Internal reference voltage spread over the temperature range VRERINTVDD = 3 V ±10 mV; specified by design, not tested in productionmax 10 mV40
Temperature coefficient TCoeffSpecified by design, not tested in productionmax 100 ppm/°C40
Supply current in Run mode IDDExternal clock, all peripherals enabled; 72 MHz; TA = 85 °Cmax 50 mA41
Supply current in Run mode IDDExternal clock, all peripherals enabled; 48 MHz; TA = 85 °Cmax 36.1 mA41
Supply current in Run mode IDDExternal clock, all peripherals enabled; 36 MHz; TA = 85 °Cmax 28.6 mA41
Supply current in Run mode IDDExternal clock, all peripherals enabled; 24 MHz; TA = 85 °Cmax 19.9 mA41
Supply current in Run mode IDDExternal clock, all peripherals enabled; 16 MHz; TA = 85 °Cmax 14.7 mA41
Supply current in Run mode IDDExternal clock, all peripherals enabled; 8 MHz; TA = 85 °Cmax 8.6 mA41
Supply current in Run mode IDDExternal clock, all peripherals disabled; 72 MHz; TA = 85 °Cmax 32.8 mA41
Supply current in Run mode IDDExternal clock, all peripherals disabled; 48 MHz; TA = 85 °Cmax 24.4 mA41
Supply current in Run mode IDDExternal clock, all peripherals disabled; 36 MHz; TA = 85 °Cmax 19.8 mA41
Supply current in Run mode IDDExternal clock, all peripherals disabled; 24 MHz; TA = 85 °Cmax 13.9 mA41
Supply current in Run mode IDDExternal clock, all peripherals disabled; 16 MHz; TA = 85 °Cmax 10.7 mA41
Supply current in Run mode IDDExternal clock, all peripherals disabled; 8 MHz; TA = 85 °Cmax 6.8 mA41
Supply current in Run mode IDDExternal clock, all peripherals enabled; 72 MHz; TA = 85 °Cmax 48 mA41
Supply current in Run mode IDDExternal clock, all peripherals enabled; 48 MHz; TA = 85 °Cmax 31.5 mA41
Supply current in Run mode IDDExternal clock, all peripherals enabled; 36 MHz; TA = 85 °Cmax 24 mA41
Supply current in Run mode IDDExternal clock, all peripherals enabled; 24 MHz; TA = 85 °Cmax 17.5 mA41
Supply current in Run mode IDDExternal clock, all peripherals enabled; 16 MHz; TA = 85 °Cmax 12.5 mA41
Supply current in Run mode IDDExternal clock, all peripherals enabled; 8 MHz; TA = 85 °Cmax 7.5 mA41
Supply current in Run mode IDDExternal clock, all peripherals disabled; 72 MHz; TA = 85 °Cmax 29 mA41
Supply current in Run mode IDDExternal clock, all peripherals disabled; 48 MHz; TA = 85 °Cmax 20.5 mA41
Supply current in Run mode IDDExternal clock, all peripherals disabled; 36 MHz; TA = 85 °Cmax 16 mA41
Supply current in Run mode IDDExternal clock, all peripherals disabled; 24 MHz; TA = 85 °Cmax 11.5 mA41
Supply current in Run mode IDDExternal clock, all peripherals disabled; 16 MHz; TA = 85 °Cmax 8.5 mA41
Supply current in Run mode IDDExternal clock, all peripherals disabled; 8 MHz; TA = 85 °Cmax 5.5 mA41
Supply current in Stop mode IDDRegulator in Run mode; low-speed and high-speed internal RC oscillators and high-speed oscillator OFF; no independent watchdog; VDD = 2.4 V; TA = 25 °Ctyp 23.5 uA44
Supply current in Stop mode IDDRegulator in Run mode; low-speed and high-speed internal RC oscillators and high-speed oscillator OFF; no independent watchdog; VDD = 3.3 V; TA = 25 °Ctyp 24 uA44
Supply current in Stop mode IDDRegulator in Run mode; low-speed and high-speed internal RC oscillators and high-speed oscillator OFF; no independent watchdog; TA = 85 °Cmax 200 uA44
Supply current in Stop mode IDDRegulator in Low-power mode; low-speed and high-speed internal RC oscillators and high-speed oscillator OFF; no independent watchdog; VDD = 2.4 V; TA = 25 °Ctyp 13.5 uA44
Supply current in Stop mode IDDRegulator in Low-power mode; low-speed and high-speed internal RC oscillators and high-speed oscillator OFF; no independent watchdog; VDD = 3.3 V; TA = 25 °Ctyp 14 uA44
Supply current in Stop mode IDDRegulator in Low-power mode; low-speed and high-speed internal RC oscillators and high-speed oscillator OFF; no independent watchdog; TA = 85 °Cmax 180 uA44
Supply current in Standby mode IDDLow-speed internal RC oscillator and independent watchdog ON; VDD = 2.4 V; TA = 25 °Ctyp 2.6 uA44
Supply current in Standby mode IDDLow-speed internal RC oscillator and independent watchdog ON; VDD = 3.3 V; TA = 25 °Ctyp 3.4 uA44
Supply current in Standby mode IDDLow-speed internal RC oscillator ON, independent watchdog OFF; VDD = 2.4 V; TA = 25 °Ctyp 2.4 uA44
Supply current in Standby mode IDDLow-speed internal RC oscillator ON, independent watchdog OFF; VDD = 3.3 V; TA = 25 °Ctyp 3.2 uA44
Supply current in Standby mode IDDLow-speed internal RC oscillator and independent watchdog OFF, low-speed oscillator and RTC OFF; VDD = 2.4 V; TA = 25 °Ctyp 1.7 uA44
Supply current in Standby mode IDDLow-speed internal RC oscillator and independent watchdog OFF, low-speed oscillator and RTC OFF; VDD = 3.3 V; TA = 25 °Ctyp 2 uA44
Supply current in Standby mode IDDLow-speed internal RC oscillator and independent watchdog OFF, low-speed oscillator and RTC OFF; TA = 85 °Cmax 4 uA44
Backup domain supply current IDD_VBATLow-speed oscillator and RTC ON; VBAT = 2.0 V; TA = 25 °Ctyp 0.9 uA44
Backup domain supply current IDD_VBATLow-speed oscillator and RTC ON; VBAT = 2.4 V; TA = 25 °Ctyp 1.1 uA44
Backup domain supply current IDD_VBATLow-speed oscillator and RTC ON; VBAT = 3.3 V; TA = 25 °Ctyp 1.4 uA44
Backup domain supply current IDD_VBATLow-speed oscillator and RTC ON; TA = 85 °Cmax 1.9 uA44
Supply current in Run mode IDDExternal clock; 72 MHz; all peripherals enabled; TA = 25 °C, VDD = 3.3 Vtyp 36 mA47
Supply current in Run mode IDDExternal clock; 72 MHz; all peripherals disabled; TA = 25 °C, VDD = 3.3 Vtyp 27 mA47
Supply current in Run mode IDDExternal clock; 48 MHz; all peripherals enabled; TA = 25 °C, VDD = 3.3 Vtyp 24.2 mA47
Supply current in Run mode IDDExternal clock; 48 MHz; all peripherals disabled; TA = 25 °C, VDD = 3.3 Vtyp 18.6 mA47
Supply current in Run mode IDDExternal clock; 36 MHz; all peripherals enabled; TA = 25 °C, VDD = 3.3 Vtyp 19 mA47
Supply current in Run mode IDDExternal clock; 36 MHz; all peripherals disabled; TA = 25 °C, VDD = 3.3 Vtyp 14.8 mA47
Supply current in Run mode IDDExternal clock; 24 MHz; all peripherals enabled; TA = 25 °C, VDD = 3.3 Vtyp 12.9 mA47
Supply current in Run mode IDDExternal clock; 24 MHz; all peripherals disabled; TA = 25 °C, VDD = 3.3 Vtyp 10.1 mA47
Supply current in Run mode IDDExternal clock; 16 MHz; all peripherals enabled; TA = 25 °C, VDD = 3.3 Vtyp 9.3 mA47
Supply current in Run mode IDDExternal clock; 16 MHz; all peripherals disabled; TA = 25 °C, VDD = 3.3 Vtyp 7.4 mA47
Supply current in Run mode IDDExternal clock; 8 MHz; all peripherals enabled; TA = 25 °C, VDD = 3.3 Vtyp 5.5 mA47
Supply current in Run mode IDDExternal clock; 8 MHz; all peripherals disabled; TA = 25 °C, VDD = 3.3 Vtyp 4.6 mA47
Supply current in Run mode IDDExternal clock; 4 MHz; all peripherals enabled; TA = 25 °C, VDD = 3.3 Vtyp 3.3 mA47
Supply current in Run mode IDDExternal clock; 4 MHz; all peripherals disabled; TA = 25 °C, VDD = 3.3 Vtyp 2.8 mA47
Supply current in Run mode IDDExternal clock; 2 MHz; all peripherals enabled; TA = 25 °C, VDD = 3.3 Vtyp 2.2 mA47
Supply current in Run mode IDDExternal clock; 2 MHz; all peripherals disabled; TA = 25 °C, VDD = 3.3 Vtyp 1.9 mA47
Supply current in Run mode IDDExternal clock; 1 MHz; all peripherals enabled; TA = 25 °C, VDD = 3.3 Vtyp 1.6 mA47
Supply current in Run mode IDDExternal clock; 1 MHz; all peripherals disabled; TA = 25 °C, VDD = 3.3 Vtyp 1.45 mA47
Supply current in Run mode IDDExternal clock; 500 kHz; all peripherals enabled; TA = 25 °C, VDD = 3.3 Vtyp 1.3 mA47
Supply current in Run mode IDDExternal clock; 500 kHz; all peripherals disabled; TA = 25 °C, VDD = 3.3 Vtyp 1.25 mA47
Supply current in Run mode IDDExternal clock; 125 kHz; all peripherals enabled; TA = 25 °C, VDD = 3.3 Vtyp 1.08 mA47
Supply current in Run mode IDDExternal clock; 125 kHz; all peripherals disabled; TA = 25 °C, VDD = 3.3 Vtyp 1.06 mA47
Supply current in Run mode IDDHSI, AHB prescaler used to reduce frequency; 64 MHz; all peripherals enabled; TA = 25 °C, VDD = 3.3 Vtyp 31.4 mA47
Supply current in Run mode IDDHSI, AHB prescaler used to reduce frequency; 64 MHz; all peripherals disabled; TA = 25 °C, VDD = 3.3 Vtyp 23.9 mA47
Supply current in Run mode IDDHSI, AHB prescaler used to reduce frequency; 48 MHz; all peripherals enabled; TA = 25 °C, VDD = 3.3 Vtyp 23.5 mA47
Supply current in Run mode IDDHSI, AHB prescaler used to reduce frequency; 48 MHz; all peripherals disabled; TA = 25 °C, VDD = 3.3 Vtyp 17.9 mA47
Supply current in Run mode IDDHSI, AHB prescaler used to reduce frequency; 36 MHz; all peripherals enabled; TA = 25 °C, VDD = 3.3 Vtyp 18.3 mA47
Supply current in Run mode IDDHSI, AHB prescaler used to reduce frequency; 36 MHz; all peripherals disabled; TA = 25 °C, VDD = 3.3 Vtyp 14.1 mA47
Supply current in Run mode IDDHSI, AHB prescaler used to reduce frequency; 24 MHz; all peripherals enabled; TA = 25 °C, VDD = 3.3 Vtyp 12.2 mA47
Supply current in Run mode IDDHSI, AHB prescaler used to reduce frequency; 24 MHz; all peripherals disabled; TA = 25 °C, VDD = 3.3 Vtyp 9.5 mA47
Supply current in Run mode IDDHSI, AHB prescaler used to reduce frequency; 16 MHz; all peripherals enabled; TA = 25 °C, VDD = 3.3 Vtyp 8.5 mA47
Supply current in Run mode IDDHSI, AHB prescaler used to reduce frequency; 16 MHz; all peripherals disabled; TA = 25 °C, VDD = 3.3 Vtyp 6.8 mA47
Supply current in Run mode IDDHSI, AHB prescaler used to reduce frequency; 8 MHz; all peripherals enabled; TA = 25 °C, VDD = 3.3 Vtyp 4.9 mA47
Supply current in Run mode IDDHSI, AHB prescaler used to reduce frequency; 8 MHz; all peripherals disabled; TA = 25 °C, VDD = 3.3 Vtyp 4 mA47
Supply current in Run mode IDDHSI, AHB prescaler used to reduce frequency; 4 MHz; all peripherals enabled; TA = 25 °C, VDD = 3.3 Vtyp 2.7 mA47
Supply current in Run mode IDDHSI, AHB prescaler used to reduce frequency; 4 MHz; all peripherals disabled; TA = 25 °C, VDD = 3.3 Vtyp 2.2 mA47
Supply current in Run mode IDDHSI, AHB prescaler used to reduce frequency; 2 MHz; all peripherals enabled; TA = 25 °C, VDD = 3.3 Vtyp 1.6 mA47
Supply current in Run mode IDDHSI, AHB prescaler used to reduce frequency; 2 MHz; all peripherals disabled; TA = 25 °C, VDD = 3.3 Vtyp 1.4 mA47
Supply current in Run mode IDDHSI, AHB prescaler used to reduce frequency; 1 MHz; all peripherals enabled; TA = 25 °C, VDD = 3.3 Vtyp 1.02 mA47
Supply current in Run mode IDDHSI, AHB prescaler used to reduce frequency; 1 MHz; all peripherals disabled; TA = 25 °C, VDD = 3.3 Vtyp 0.9 mA47
Supply current in Run mode IDDHSI, AHB prescaler used to reduce frequency; 500 kHz; all peripherals enabled; TA = 25 °C, VDD = 3.3 Vtyp 0.73 mA47
Supply current in Run mode IDDHSI, AHB prescaler used to reduce frequency; 500 kHz; all peripherals disabled; TA = 25 °C, VDD = 3.3 Vtyp 0.67 mA47
Supply current in Run mode IDDHSI, AHB prescaler used to reduce frequency; 125 kHz; all peripherals enabled; TA = 25 °C, VDD = 3.3 Vtyp 0.5 mA47
Supply current in Run mode IDDHSI, AHB prescaler used to reduce frequency; 125 kHz; all peripherals disabled; TA = 25 °C, VDD = 3.3 Vtyp 0.48 mA47
Thermal resistance junction-ambient ΘJALQFP64 - 10 × 10 mm / 0.5 mm pitchtyp 45 °C/W104
Input voltage on any other pin VINAbsolute maximum; minimum VSS − 0.3 Vmax 4 V37
Injected current on any other pin IINJ(PIN)Absolute maximum, ±5 mAmax 5 mA37
Total injected current (sum of all I/O and control pins) ΣIINJ(PIN)Absolute maximum, ±25 mAmax 25 mA37
Storage temperature range TSTGmin -65 · max 150 °C37
Maximum junction temperature TJmax 150 °C37
ADC sampling time when reading the internal reference voltage TS_vrefinttyp 5.1 · max 17.1 us40
Internal reference voltage spread over the temperature range VRERINTVDD = 3 V ±10 mVmax 10 mV40
Temperature coefficient TCoeffmax 100 ppm/°C40
Supply current in Run mode IDDExternal clock, all peripherals enabled; 72 MHz; TA = 105 °Cmax 50.3 mA41
Supply current in Run mode IDDExternal clock, all peripherals enabled; 48 MHz; TA = 105 °Cmax 36.2 mA41
Supply current in Run mode IDDExternal clock, all peripherals enabled; 36 MHz; TA = 105 °Cmax 28.7 mA41
Supply current in Run mode IDDExternal clock, all peripherals enabled; 24 MHz; TA = 105 °Cmax 20.1 mA41
Supply current in Run mode IDDExternal clock, all peripherals enabled; 16 MHz; TA = 105 °Cmax 14.9 mA41
Supply current in Run mode IDDExternal clock, all peripherals enabled; 8 MHz; TA = 105 °Cmax 8.9 mA41
Supply current in Run mode IDDExternal clock, all peripherals disabled; 72 MHz; TA = 105 °Cmax 32.9 mA41
Supply current in Run mode IDDExternal clock, all peripherals disabled; 48 MHz; TA = 105 °Cmax 24.5 mA41
Supply current in Run mode IDDExternal clock, all peripherals disabled; 36 MHz; TA = 105 °Cmax 19.9 mA41
Supply current in Run mode IDDExternal clock, all peripherals disabled; 24 MHz; TA = 105 °Cmax 14.2 mA41
Supply current in Run mode IDDExternal clock, all peripherals disabled; 16 MHz; TA = 105 °Cmax 11 mA41
Supply current in Run mode IDDExternal clock, all peripherals disabled; 8 MHz; TA = 105 °Cmax 7.1 mA41
Supply current in Run mode IDDExternal clock, all peripherals enabled; 72 MHz; TA = 105 °Cmax 50 mA41
Supply current in Run mode IDDExternal clock, all peripherals enabled; 48 MHz; TA = 105 °Cmax 32 mA41
Supply current in Run mode IDDExternal clock, all peripherals enabled; 36 MHz; TA = 105 °Cmax 25.5 mA41
Supply current in Run mode IDDExternal clock, all peripherals enabled; 24 MHz; TA = 105 °Cmax 18 mA41
Supply current in Run mode IDDExternal clock, all peripherals enabled; 16 MHz; TA = 105 °Cmax 13 mA41
Supply current in Run mode IDDExternal clock, all peripherals enabled; 8 MHz; TA = 105 °Cmax 8 mA41
Supply current in Run mode IDDExternal clock, all peripherals disabled; 72 MHz; TA = 105 °Cmax 29.5 mA41
Supply current in Run mode IDDExternal clock, all peripherals disabled; 48 MHz; TA = 105 °Cmax 21 mA41
Supply current in Run mode IDDExternal clock, all peripherals disabled; 36 MHz; TA = 105 °Cmax 16.5 mA41
Supply current in Run mode IDDExternal clock, all peripherals disabled; 24 MHz; TA = 105 °Cmax 12 mA41
Supply current in Run mode IDDExternal clock, all peripherals disabled; 16 MHz; TA = 105 °Cmax 9 mA41
Supply current in Run mode IDDExternal clock, all peripherals disabled; 8 MHz; TA = 105 °Cmax 6 mA41
Supply current in Sleep mode IDDExternal clock, all peripherals enabled; 72 MHz; TA = 85 °Cmax 30 mA43
Supply current in Sleep mode IDDExternal clock, all peripherals enabled; 72 MHz; TA = 105 °Cmax 32 mA43
Supply current in Sleep mode IDDExternal clock, all peripherals enabled; 48 MHz; TA = 85 °Cmax 20 mA43
Supply current in Sleep mode IDDExternal clock, all peripherals enabled; 48 MHz; TA = 105 °Cmax 20.5 mA43
Supply current in Sleep mode IDDExternal clock, all peripherals enabled; 36 MHz; TA = 85 °Cmax 15.5 mA43
Supply current in Sleep mode IDDExternal clock, all peripherals enabled; 36 MHz; TA = 105 °Cmax 16 mA43
Supply current in Sleep mode IDDExternal clock, all peripherals enabled; 24 MHz; TA = 85 °Cmax 11.5 mA43
Supply current in Sleep mode IDDExternal clock, all peripherals enabled; 24 MHz; TA = 105 °Cmax 12 mA43
Supply current in Sleep mode IDDExternal clock, all peripherals enabled; 16 MHz; TA = 85 °Cmax 8.5 mA43
Supply current in Sleep mode IDDExternal clock, all peripherals enabled; 16 MHz; TA = 105 °Cmax 9 mA43
Supply current in Sleep mode IDDExternal clock, all peripherals enabled; 8 MHz; TA = 85 °Cmax 5.5 mA43
Supply current in Sleep mode IDDExternal clock, all peripherals enabled; 8 MHz; TA = 105 °Cmax 6 mA43
Supply current in Sleep mode IDDExternal clock, all peripherals disabled; 72 MHz; TA = 85 °Cmax 7.5 mA43
Supply current in Sleep mode IDDExternal clock, all peripherals disabled; 72 MHz; TA = 105 °Cmax 8 mA43
Supply current in Sleep mode IDDExternal clock, all peripherals disabled; 48 MHz; TA = 85 °Cmax 6 mA43
Supply current in Sleep mode IDDExternal clock, all peripherals disabled; 48 MHz; TA = 105 °Cmax 6.5 mA43
Supply current in Sleep mode IDDExternal clock, all peripherals disabled; 36 MHz; TA = 85 °Cmax 5 mA43
Supply current in Sleep mode IDDExternal clock, all peripherals disabled; 36 MHz; TA = 105 °Cmax 5.5 mA43
Supply current in Sleep mode IDDExternal clock, all peripherals disabled; 24 MHz; TA = 85 °Cmax 4.5 mA43
Supply current in Sleep mode IDDExternal clock, all peripherals disabled; 24 MHz; TA = 105 °Cmax 5 mA43
Supply current in Sleep mode IDDExternal clock, all peripherals disabled; 16 MHz; TA = 85 °Cmax 4 mA43
Supply current in Sleep mode IDDExternal clock, all peripherals disabled; 16 MHz; TA = 105 °Cmax 4.5 mA43
Supply current in Sleep mode IDDExternal clock, all peripherals disabled; 8 MHz; TA = 85 °Cmax 3 mA43
Supply current in Sleep mode IDDExternal clock, all peripherals disabled; 8 MHz; TA = 105 °Cmax 4 mA43
Supply current in Stop mode IDDRegulator in Run mode; internal RC oscillators and high-speed oscillator OFF; no independent watchdog; VDD = 2.4 V, TA = 25 °Ctyp 23.5 uA44
Supply current in Stop mode IDDRegulator in Run mode; internal RC oscillators and high-speed oscillator OFF; no independent watchdog; VDD = 3.3 V, TA = 25 °Ctyp 24 uA44
Supply current in Stop mode IDDRegulator in Run mode; internal RC oscillators and high-speed oscillator OFF; no independent watchdog; TA = 85 °Cmax 200 uA44
Supply current in Stop mode IDDRegulator in Run mode; internal RC oscillators and high-speed oscillator OFF; no independent watchdog; TA = 105 °Cmax 370 uA44
Supply current in Stop mode IDDRegulator in Low-power mode; internal RC oscillators and high-speed oscillator OFF; no independent watchdog; VDD = 2.4 V, TA = 25 °Ctyp 13.5 uA44
Supply current in Stop mode IDDRegulator in Low-power mode; internal RC oscillators and high-speed oscillator OFF; no independent watchdog; VDD = 3.3 V, TA = 25 °Ctyp 14 uA44
Supply current in Stop mode IDDRegulator in Low-power mode; internal RC oscillators and high-speed oscillator OFF; no independent watchdog; TA = 85 °Cmax 180 uA44
Supply current in Stop mode IDDRegulator in Low-power mode; internal RC oscillators and high-speed oscillator OFF; no independent watchdog; TA = 105 °Cmax 340 uA44
Supply current in Standby mode IDDLow-speed internal RC oscillator and independent watchdog ON; VDD = 2.4 V, TA = 25 °Ctyp 2.6 uA44
Supply current in Standby mode IDDLow-speed internal RC oscillator and independent watchdog ON; VDD = 3.3 V, TA = 25 °Ctyp 3.4 uA44
Supply current in Standby mode IDDLow-speed internal RC oscillator ON, independent watchdog OFF; VDD = 2.4 V, TA = 25 °Ctyp 2.4 uA44
Supply current in Standby mode IDDLow-speed internal RC oscillator ON, independent watchdog OFF; VDD = 3.3 V, TA = 25 °Ctyp 3.2 uA44
Supply current in Standby mode IDDLow-speed internal RC oscillator, independent watchdog, low-speed oscillator and RTC OFF; VDD = 2.4 V, TA = 25 °Ctyp 1.7 uA44
Supply current in Standby mode IDDLow-speed internal RC oscillator, independent watchdog, low-speed oscillator and RTC OFF; VDD = 3.3 V, TA = 25 °Ctyp 2 uA44
Supply current in Standby mode IDDLow-speed internal RC oscillator, independent watchdog, low-speed oscillator and RTC OFF; TA = 85 °Cmax 4 uA44
Supply current in Standby mode IDDLow-speed internal RC oscillator, independent watchdog, low-speed oscillator and RTC OFF; TA = 105 °Cmax 5 uA44
Backup domain supply current IDD_VBATLow-speed oscillator and RTC ON; VBAT = 2.0 V, TA = 25 °Ctyp 0.9 uA44
Backup domain supply current IDD_VBATLow-speed oscillator and RTC ON; VBAT = 2.4 V, TA = 25 °Ctyp 1.1 uA44
Backup domain supply current IDD_VBATLow-speed oscillator and RTC ON; VBAT = 3.3 V, TA = 25 °Ctyp 1.4 uA44
Backup domain supply current IDD_VBATLow-speed oscillator and RTC ON; TA = 105 °Cmax 2.2 uA44
Supply current in Run mode IDDHSI, AHB prescaler; 64 MHz; all peripherals enabled; TA = 25 °C, VDD = 3.3 Vtyp 31.4 mA47
Supply current in Run mode IDDHSI, AHB prescaler; 64 MHz; all peripherals disabled; TA = 25 °C, VDD = 3.3 Vtyp 23.9 mA47
Supply current in Run mode IDDHSI, AHB prescaler; 48 MHz; all peripherals enabled; TA = 25 °C, VDD = 3.3 Vtyp 23.5 mA47
Supply current in Run mode IDDHSI, AHB prescaler; 48 MHz; all peripherals disabled; TA = 25 °C, VDD = 3.3 Vtyp 17.9 mA47
Supply current in Run mode IDDHSI, AHB prescaler; 36 MHz; all peripherals enabled; TA = 25 °C, VDD = 3.3 Vtyp 18.3 mA47
Supply current in Run mode IDDHSI, AHB prescaler; 36 MHz; all peripherals disabled; TA = 25 °C, VDD = 3.3 Vtyp 14.1 mA47
Supply current in Run mode IDDHSI, AHB prescaler; 24 MHz; all peripherals enabled; TA = 25 °C, VDD = 3.3 Vtyp 12.2 mA47
Supply current in Run mode IDDHSI, AHB prescaler; 24 MHz; all peripherals disabled; TA = 25 °C, VDD = 3.3 Vtyp 9.5 mA47
Supply current in Run mode IDDHSI, AHB prescaler; 16 MHz; all peripherals enabled; TA = 25 °C, VDD = 3.3 Vtyp 8.5 mA47
Supply current in Run mode IDDHSI, AHB prescaler; 16 MHz; all peripherals disabled; TA = 25 °C, VDD = 3.3 Vtyp 6.8 mA47
Supply current in Run mode IDDHSI, AHB prescaler; 8 MHz; all peripherals enabled; TA = 25 °C, VDD = 3.3 Vtyp 4.9 mA47
Supply current in Run mode IDDHSI, AHB prescaler; 8 MHz; all peripherals disabled; TA = 25 °C, VDD = 3.3 Vtyp 4 mA47
Supply current in Run mode IDDHSI, AHB prescaler; 4 MHz; all peripherals enabled; TA = 25 °C, VDD = 3.3 Vtyp 2.7 mA47
Supply current in Run mode IDDHSI, AHB prescaler; 4 MHz; all peripherals disabled; TA = 25 °C, VDD = 3.3 Vtyp 2.2 mA47
Supply current in Run mode IDDHSI, AHB prescaler; 2 MHz; all peripherals enabled; TA = 25 °C, VDD = 3.3 Vtyp 1.6 mA47
Supply current in Run mode IDDHSI, AHB prescaler; 2 MHz; all peripherals disabled; TA = 25 °C, VDD = 3.3 Vtyp 1.4 mA47
Supply current in Run mode IDDHSI, AHB prescaler; 1 MHz; all peripherals enabled; TA = 25 °C, VDD = 3.3 Vtyp 1.02 mA47
Supply current in Run mode IDDHSI, AHB prescaler; 1 MHz; all peripherals disabled; TA = 25 °C, VDD = 3.3 Vtyp 0.9 mA47
Supply current in Run mode IDDHSI, AHB prescaler; 500 kHz; all peripherals enabled; TA = 25 °C, VDD = 3.3 Vtyp 0.73 mA47
Supply current in Run mode IDDHSI, AHB prescaler; 500 kHz; all peripherals disabled; TA = 25 °C, VDD = 3.3 Vtyp 0.67 mA47
Supply current in Run mode IDDHSI, AHB prescaler; 125 kHz; all peripherals enabled; TA = 25 °C, VDD = 3.3 Vtyp 0.5 mA47
Supply current in Run mode IDDHSI, AHB prescaler; 125 kHz; all peripherals disabled; TA = 25 °C, VDD = 3.3 Vtyp 0.48 mA47
Supply current in Sleep mode IDDExternal clock; 72 MHz; all peripherals enabled; TA = 25 °C, VDD = 3.3 Vtyp 14.4 mA48
Supply current in Sleep mode IDDExternal clock; 72 MHz; all peripherals disabled; TA = 25 °C, VDD = 3.3 Vtyp 5.5 mA48
Supply current in Sleep mode IDDExternal clock; 48 MHz; all peripherals enabled; TA = 25 °C, VDD = 3.3 Vtyp 9.9 mA48
Supply current in Sleep mode IDDExternal clock; 48 MHz; all peripherals disabled; TA = 25 °C, VDD = 3.3 Vtyp 3.9 mA48
Supply current in Sleep mode IDDExternal clock; 36 MHz; all peripherals enabled; TA = 25 °C, VDD = 3.3 Vtyp 7.6 mA48
Supply current in Sleep mode IDDExternal clock; 36 MHz; all peripherals disabled; TA = 25 °C, VDD = 3.3 Vtyp 3.1 mA48
Supply current in Sleep mode IDDExternal clock; 24 MHz; all peripherals enabled; TA = 25 °C, VDD = 3.3 Vtyp 5.3 mA48
Supply current in Sleep mode IDDExternal clock; 24 MHz; all peripherals disabled; TA = 25 °C, VDD = 3.3 Vtyp 2.3 mA48
Supply current in Sleep mode IDDExternal clock; 16 MHz; all peripherals enabled; TA = 25 °C, VDD = 3.3 Vtyp 3.8 mA48
Supply current in Sleep mode IDDExternal clock; 16 MHz; all peripherals disabled; TA = 25 °C, VDD = 3.3 Vtyp 1.8 mA48
Supply current in Sleep mode IDDExternal clock; 8 MHz; all peripherals enabled; TA = 25 °C, VDD = 3.3 Vtyp 2.1 mA48
Supply current in Sleep mode IDDExternal clock; 8 MHz; all peripherals disabled; TA = 25 °C, VDD = 3.3 Vtyp 1.2 mA48
Supply current in Sleep mode IDDExternal clock; 4 MHz; all peripherals enabled; TA = 25 °C, VDD = 3.3 Vtyp 1.6 mA48
Supply current in Sleep mode IDDExternal clock; 4 MHz; all peripherals disabled; TA = 25 °C, VDD = 3.3 Vtyp 1.1 mA48
Supply current in Sleep mode IDDExternal clock; 2 MHz; all peripherals enabled; TA = 25 °C, VDD = 3.3 Vtyp 1.3 mA48
Supply current in Sleep mode IDDExternal clock; 2 MHz; all peripherals disabled; TA = 25 °C, VDD = 3.3 Vtyp 1 mA48
Supply current in Sleep mode IDDExternal clock; 1 MHz; all peripherals enabled; TA = 25 °C, VDD = 3.3 Vtyp 1.11 mA48
Supply current in Sleep mode IDDExternal clock; 1 MHz; all peripherals disabled; TA = 25 °C, VDD = 3.3 Vtyp 0.98 mA48
Supply current in Sleep mode IDDExternal clock; 500 kHz; all peripherals enabled; TA = 25 °C, VDD = 3.3 Vtyp 1.04 mA48
Supply current in Sleep mode IDDExternal clock; 500 kHz; all peripherals disabled; TA = 25 °C, VDD = 3.3 Vtyp 0.96 mA48
Supply current in Sleep mode IDDExternal clock; 125 kHz; all peripherals enabled; TA = 25 °C, VDD = 3.3 Vtyp 0.98 mA48
Supply current in Sleep mode IDDExternal clock; 125 kHz; all peripherals disabled; TA = 25 °C, VDD = 3.3 Vtyp 0.95 mA48
Supply current in Sleep mode IDDHSI, AHB prescaler; 64 MHz; all peripherals enabled; TA = 25 °C, VDD = 3.3 Vtyp 12.3 mA48
Supply current in Sleep mode IDDHSI, AHB prescaler; 64 MHz; all peripherals disabled; TA = 25 °C, VDD = 3.3 Vtyp 4.4 mA48
Supply current in Sleep mode IDDHSI, AHB prescaler; 48 MHz; all peripherals enabled; TA = 25 °C, VDD = 3.3 Vtyp 9.3 mA48
Supply current in Sleep mode IDDHSI, AHB prescaler; 48 MHz; all peripherals disabled; TA = 25 °C, VDD = 3.3 Vtyp 3.3 mA48
Supply current in Sleep mode IDDHSI, AHB prescaler; 36 MHz; all peripherals enabled; TA = 25 °C, VDD = 3.3 Vtyp 7 mA48
Supply current in Sleep mode IDDHSI, AHB prescaler; 36 MHz; all peripherals disabled; TA = 25 °C, VDD = 3.3 Vtyp 2.5 mA48
Supply current in Sleep mode IDDHSI, AHB prescaler; 24 MHz; all peripherals enabled; TA = 25 °C, VDD = 3.3 Vtyp 4.8 mA48
Supply current in Sleep mode IDDHSI, AHB prescaler; 24 MHz; all peripherals disabled; TA = 25 °C, VDD = 3.3 Vtyp 1.8 mA48
Supply current in Sleep mode IDDHSI, AHB prescaler; 16 MHz; all peripherals enabled; TA = 25 °C, VDD = 3.3 Vtyp 3.2 mA48
Supply current in Sleep mode IDDHSI, AHB prescaler; 16 MHz; all peripherals disabled; TA = 25 °C, VDD = 3.3 Vtyp 1.2 mA48
Supply current in Sleep mode IDDHSI, AHB prescaler; 8 MHz; all peripherals enabled; TA = 25 °C, VDD = 3.3 Vtyp 1.6 mA48
Supply current in Sleep mode IDDHSI, AHB prescaler; 8 MHz; all peripherals disabled; TA = 25 °C, VDD = 3.3 Vtyp 0.6 mA48
Supply current in Sleep mode IDDHSI, AHB prescaler; 4 MHz; all peripherals enabled; TA = 25 °C, VDD = 3.3 Vtyp 1 mA48
Supply current in Sleep mode IDDHSI, AHB prescaler; 4 MHz; all peripherals disabled; TA = 25 °C, VDD = 3.3 Vtyp 0.5 mA48
Supply current in Sleep mode IDDHSI, AHB prescaler; 2 MHz; all peripherals enabled; TA = 25 °C, VDD = 3.3 Vtyp 0.72 mA48
Supply current in Sleep mode IDDHSI, AHB prescaler; 2 MHz; all peripherals disabled; TA = 25 °C, VDD = 3.3 Vtyp 0.47 mA48
Supply current in Sleep mode IDDHSI, AHB prescaler; 1 MHz; all peripherals enabled; TA = 25 °C, VDD = 3.3 Vtyp 0.56 mA48
Supply current in Sleep mode IDDHSI, AHB prescaler; 1 MHz; all peripherals disabled; TA = 25 °C, VDD = 3.3 Vtyp 0.44 mA48
Supply current in Sleep mode IDDHSI, AHB prescaler; 500 kHz; all peripherals enabled; TA = 25 °C, VDD = 3.3 Vtyp 0.49 mA48
Supply current in Sleep mode IDDHSI, AHB prescaler; 500 kHz; all peripherals disabled; TA = 25 °C, VDD = 3.3 Vtyp 0.42 mA48
Supply current in Sleep mode IDDHSI, AHB prescaler; 125 kHz; all peripherals enabled; TA = 25 °C, VDD = 3.3 Vtyp 0.43 mA48
Supply current in Sleep mode IDDHSI, AHB prescaler; 125 kHz; all peripherals disabled; TA = 25 °C, VDD = 3.3 Vtyp 0.41 mA48
DMA1AHB (up to 72 MHz); only this peripheral clocked ontyp 16.53 uA/MHz49
BusMatrixAHB (up to 72 MHz); automatically active when CPU or DMA is ONtyp 8.33 uA/MHz49
APB1-BridgeAPB1 (up to 36 MHz)typ 10.28 uA/MHz49
TIM2APB1 (up to 36 MHz); only this peripheral clocked ontyp 32.5 uA/MHz49
TIM3APB1 (up to 36 MHz); only this peripheral clocked ontyp 31.39 uA/MHz49
TIM4APB1 (up to 36 MHz); only this peripheral clocked ontyp 31.94 uA/MHz49
SPI2APB1 (up to 36 MHz); only this peripheral clocked ontyp 4.17 uA/MHz49
USART2APB1 (up to 36 MHz); only this peripheral clocked ontyp 12.22 uA/MHz49
USART3APB1 (up to 36 MHz); only this peripheral clocked ontyp 12.22 uA/MHz49
I2C1APB1 (up to 36 MHz); only this peripheral clocked ontyp 10 uA/MHz49
I2C2APB1 (up to 36 MHz); only this peripheral clocked ontyp 10 uA/MHz49
USBAPB1 (up to 36 MHz); only this peripheral clocked ontyp 17.78 uA/MHz49
CAN1APB1 (up to 36 MHz); only this peripheral clocked ontyp 18.06 uA/MHz49
WWDGAPB1 (up to 36 MHz); only this peripheral clocked ontyp 2.5 uA/MHz49
PWRAPB1 (up to 36 MHz); only this peripheral clocked ontyp 1.67 uA/MHz49
BKPAPB1 (up to 36 MHz); only this peripheral clocked ontyp 2.5 uA/MHz49
IWDGAPB1 (up to 36 MHz); only this peripheral clocked ontyp 11.67 uA/MHz49
APB2-BridgeAPB2 (up to 72 MHz)typ 3.75 uA/MHz50
GPIOAAPB2 (up to 72 MHz); only this peripheral clocked ontyp 6.67 uA/MHz50
GPIOBAPB2 (up to 72 MHz); only this peripheral clocked ontyp 6.53 uA/MHz50
GPIOCAPB2 (up to 72 MHz); only this peripheral clocked ontyp 6.53 uA/MHz50
GPIODAPB2 (up to 72 MHz); only this peripheral clocked ontyp 6.53 uA/MHz50
GPIOEAPB2 (up to 72 MHz); only this peripheral clocked ontyp 6.39 uA/MHz50
SPI1APB2 (up to 72 MHz); only this peripheral clocked ontyp 4.72 uA/MHz50
USART1APB2 (up to 72 MHz); only this peripheral clocked ontyp 11.94 uA/MHz50
TIM1APB2 (up to 72 MHz); only this peripheral clocked ontyp 23.33 uA/MHz50
ADC1fHCLK = 56 MHz, fAPB1 = fHCLK / 2, fAPB2 = fHCLK, fADCCLK = fAPB2 / 4; add 0.65 mA analog current when ADON = 1typ 17.5 uA/MHz50
ADC2fHCLK = 56 MHz, fAPB1 = fHCLK / 2, fAPB2 = fHCLK, fADCCLK = fAPB2 / 4; add 0.65 mA analog current when ADON = 1typ 16.07 uA/MHz50
User external clock source frequency fHSE_extmin 1 · typ 8 · max 25 MHz50
OSC_IN high or low time tw(HSE)High timemin 5 ns50
OSC_IN high or low time tw(HSE)Low timemin 5 ns50
OSC_IN rise or fall time tr(HSE)Rise timemax 20 ns50
OSC_IN rise or fall time tf(HSE)Fall timemax 20 ns50
OSC_IN input capacitance Cin(HSE)typ 5 pF50
Duty cycle DuCy(HSE)min 45 · max 55 %50
OSC_IN Input leakage current ILVSS ≤ VIN ≤ VDD; maximum ±1 uAmax 1 uA50
Oscillator frequency fOSC_INmin 4 · typ 8 · max 16 MHz52
Feedback resistor RFtyp 200 kΩ52
Recommended load capacitance versus equivalent serial resistance of the crystal (RS) CRS = 30 Ωtyp 30 pF52
HSE driving current i2VDD = 3.3 V, VIN = VSS with 30 pF loadmax 1 mA52
Oscillator transconductance gmStartupmin 25 mA/V52
Startup time tSU(HSE)VDD is stabilizedtyp 2 ms52
Feedback resistor RFtyp 5 MΩ53
Recommended load capacitance versus equivalent serial resistance of the crystal (RS) CRS = 30 KΩmax 15 pF53
LSE driving current I2VDD = 3.3 V, VIN = VSSmax 1.4 uA53
Oscillator transconductance gmmin 5 uA/V53
Startup time tSU(LSE)VDD is stabilized; TA = 50 °Ctyp 1.5 s53
Startup time tSU(LSE)VDD is stabilized; TA = 25 °Ctyp 2.5 s53
Startup time tSU(LSE)VDD is stabilized; TA = 10 °Ctyp 4 s53
Startup time tSU(LSE)VDD is stabilized; TA = 0 °Ctyp 6 s53
Startup time tSU(LSE)VDD is stabilized; TA = -10 °Ctyp 10 s53
Startup time tSU(LSE)VDD is stabilized; TA = -20 °Ctyp 17 s53
Startup time tSU(LSE)VDD is stabilized; TA = -30 °Ctyp 32 s53
Startup time tSU(LSE)VDD is stabilized; TA = -40 °Ctyp 60 s53
Frequency fHSIVDD = 3.3 V, TA = –40 to 105 °Ctyp 8 MHz54
Duty cycle DuCy(HSI)VDD = 3.3 V, TA = –40 to 105 °Cmin 45 · max 55 %54
Accuracy of the HSI oscillator ACCHSIUser-trimmed with the RCC_CR register; VDD = 3.3 V, TA = –40 to 105 °Cmax 1 %54
Accuracy of the HSI oscillator ACCHSIFactory-calibrated; VDD = 3.3 V, TA = –40 to 105 °Cmin -2 · max 2.5 %54
Accuracy of the HSI oscillator ACCHSIFactory-calibrated; VDD = 3.3 V, TA = 0 to 70 °Cmin -1.3 · max 2 %54
Accuracy of the HSI oscillator ACCHSIFactory-calibrated; VDD = 3.3 V, TA = 25 °Cmin -1.1 · max 1.8 %54
HSI oscillator startup time tsu(HSI)VDD = 3.3 V, TA = –40 to 105 °Cmin 1 · max 2 us55
HSI oscillator power consumption IDD(HSI)VDD = 3.3 V, TA = –40 to 105 °Ctyp 80 · max 100 uA55
Frequency fLSIVDD = 3 V, TA = –40 to 105 °Cmin 30 · typ 40 · max 60 kHz55
LSI oscillator startup time tsu(LSI)VDD = 3 V, TA = –40 to 105 °Cmax 85 us55
LSI oscillator power consumption IDD(LSI)VDD = 3 V, TA = –40 to 105 °Ctyp 0.65 · max 1.2 uA55
Wakeup from Sleep mode tWUSLEEPtyp 1.8 us56
Wakeup from Stop mode (regulator in run mode) tWUSTOPtyp 3.6 us56
Wakeup from Stop mode (regulator in low-power mode) tWUSTOPtyp 5.4 us56
Wakeup from Standby mode tWUSTDBYtyp 50 us56
PLL input clock fPLL_INmin 1 · typ 8 · max 25 MHz56
PLL input clock duty cycle fPLL_INmin 40 · max 60 %56
PLL multiplier output clock fPLL_OUTmin 16 · max 72 MHz56
PLL lock time tLOCKmax 200 us56
Cycle-to-cycle jitter Jittermax 300 ps56
16-bit programming time tprogTA = –40 to +105 °Cmin 40 · typ 52.5 · max 70 us56
Page (1 KB) erase time tERASETA = –40 to +105 °Cmin 20 · max 40 ms56
Mass erase time tMETA = –40 to +105 °Cmin 20 · max 40 ms56
Supply current IDDRead mode; fHCLK = 72 MHz with two wait states, VDD = 3.3 V; TA = –40 to 105 °Cmax 20 mA57
Supply current IDDWrite / Erase modes; fHCLK = 72 MHz, VDD = 3.3 V; TA = –40 to 105 °Cmax 5 mA57
Supply current IDDPower-down mode / Halt; VDD = 3.0 to 3.6 V; TA = –40 to 105 °Cmax 50 uA57
Programming voltage VprogTA = –40 to 105 °Cmin 2 · max 3.6 V57
Endurance NENDTA = –40 to +85 °C (6 suffix versions)min 10 kcycles57
Data retention tRET1 kcycle at TA = 85 °Cmin 30 Years57
Data retention tRET1 kcycle at TA = 105 °Cmin 10 Years57
Data retention tRET10 kcycles at TA = 55 °Cmin 20 Years57
Electrostatic discharge voltage (human body model) VESD(HBM)TA = +25 °C; conforming to JESD22-A114; Class 2max 2000 V59
Electrostatic discharge voltage (charge device model) VESD(CDM)TA = +25 °C; conforming to ANSI/ESD STM5.3.1; Class IImax 500 V59
Output low level voltage for an I/O pin when 8 pins are sunk at same time VOLCMOS port; IIO = +8 mA; 2.7 V < VDD < 3.6 Vmax 0.4 V64
Output low level voltage for an I/O pin when 8 pins are sunk at same time VOLTTL port; IIO = +8 mA; 2.7 V < VDD < 3.6 Vmax 0.4 V64
Output high level voltage for an I/O pin when 8 pins are sourced at same time VOHTTL port; IIO = +8 mA; 2.7 V < VDD < 3.6 Vmin 2.4 V64
Output low level voltage for an I/O pin when 8 pins are sunk at same time VOLIIO = +20 mA; 2.7 V < VDD < 3.6 Vmax 1.3 V64
Output low level voltage for an I/O pin when 8 pins are sunk at same time VOLIIO = +6 mA; 2 V < VDD < 2.7 Vmax 0.4 V64
Maximum frequency fmax(IO)outMODEx[1:0] = 10; CL = 50 pF, VDD = 2 V to 3.6 Vmax 2 MHz65
Output high to low level fall time tf(IO)outMODEx[1:0] = 10; CL = 50 pF, VDD = 2 V to 3.6 Vmax 125 ns65
Output low to high level rise time tr(IO)outMODEx[1:0] = 10; CL = 50 pF, VDD = 2 V to 3.6 Vmax 125 ns65
Maximum frequency fmax(IO)outMODEx[1:0] = 01; CL = 50 pF, VDD = 2 V to 3.6 Vmax 10 MHz65
Output high to low level fall time tf(IO)outMODEx[1:0] = 01; CL = 50 pF, VDD = 2 V to 3.6 Vmax 25 ns65
Output low to high level rise time tr(IO)outMODEx[1:0] = 01; CL = 50 pF, VDD = 2 V to 3.6 Vmax 25 ns65
Maximum frequency Fmax(IO)outMODEx[1:0] = 11; CL = 30 pF, VDD = 2.7 V to 3.6 Vmax 50 MHz65
Maximum frequency Fmax(IO)outMODEx[1:0] = 11; CL = 50 pF, VDD = 2.7 V to 3.6 Vmax 30 MHz65
Maximum frequency Fmax(IO)outMODEx[1:0] = 11; CL = 50 pF, VDD = 2 V to 2.7 Vmax 20 MHz65
Output high to low level fall time tf(IO)outMODEx[1:0] = 11; CL = 30 pF, VDD = 2.7 V to 3.6 Vmax 5 ns65
Output high to low level fall time tf(IO)outMODEx[1:0] = 11; CL = 50 pF, VDD = 2.7 V to 3.6 Vmax 8 ns65
Output high to low level fall time tf(IO)outMODEx[1:0] = 11; CL = 50 pF, VDD = 2 V to 2.7 Vmax 12 ns65
Output low to high level rise time tr(IO)outMODEx[1:0] = 11; CL = 30 pF, VDD = 2.7 V to 3.6 Vmax 5 ns65
Output low to high level rise time tr(IO)outMODEx[1:0] = 11; CL = 50 pF, VDD = 2.7 V to 3.6 Vmax 8 ns65
Output low to high level rise time tr(IO)outMODEx[1:0] = 11; CL = 50 pF, VDD = 2 V to 2.7 Vmax 12 ns65
Pulse width of external signals detected by the EXTI controller tEXTIpwmin 10 ns65
USB operating voltage VDDFull USB electrical compliancemin 3 · max 3.6 V73
Differential input sensitivity VDII(USBDP, USBDM)min 0.2 V73
Differential common mode range VCMIncludes VDI rangemin 0.8 · max 2.5 V73
Single ended receiver threshold VSEmin 1.3 · max 2 V73
Static output level low VOLRL of 1.5 kΩ to 3.6 Vmax 0.3 V73
Static output level high VOHRL of 15 kΩ to VSSmin 2.8 · max 3.6 V73
Rise time trCL = 50 pF; measured from 10% to 90%min 4 · max 20 ns73
Fall time tfCL = 50 pF; measured from 10% to 90%min 4 · max 20 ns73
Rise/ fall time matching trfmtr/tfmin 90 · max 110 %73
Output signal crossover voltage VCRSmin 1.3 · max 2 V73
Power supply VDDAmin 2.4 · max 3.6 V74
Positive reference voltage VREF+Maximum VDDA; in LQFP packages VREF+ is internally connected to VDDAmin 2.4 V74
Current on the VREF input pin IVREFtyp 160 · max 220 uA74
ADC clock frequency fADCmin 0.6 · max 14 MHz74
Sampling rate fSmin 0.05 · max 1 MHz74
External trigger frequency fTRIGfADC = 14 MHzmax 823 kHz74
External trigger frequency fTRIGmax 17 1 / fADC74
External input impedance RAINSee Equation 1 and Table 47 for detailsmax 50 kΩ74
Sampling switch resistance RADCmax 1 kΩ74
Internal sample and hold capacitor CADCmax 8 pF74
Calibration time tCALfADC = 14 MHztyp 5.9 us74
Calibration time tCALtyp 83 1 / fADC74
Injection trigger conversion latency tlatfADC = 14 MHz; external triggers require an additional 1/fPCLK2 delaymax 0.214 us74
Injection trigger conversion latency tlatExternal triggers require an additional 1/fPCLK2 delaymax 3 1 / fADC74
Regular trigger conversion latency tlatrfADC = 14 MHz; external triggers require an additional 1/fPCLK2 delaymax 0.143 us74
Regular trigger conversion latency tlatrExternal triggers require an additional 1/fPCLK2 delaymax 2 1 / fADC74
Sampling time tSfADC = 14 MHzmin 0.107 · max 17.1 us74
Sampling time tSmin 1.5 · max 239.5 1 / fADC74
Power-up time tSTABmin 0 · typ 0 · max 1 us74
Total conversion time (including sampling time) tCONVfADC = 14 MHzmin 1 · max 18 us74
Total conversion time (including sampling time) tCONVtS for sampling +12.5 for successive approximationmin 14 · max 252 1 / fADC74

Pins, by the datasheet

64
1 VBAT
Backup supply. · p. 28
2 PC13-TAMPER-RTC
PC13 GPIO or TAMPER-RTC; output restrictions apply. · p. 22
3 PC14-OSC32_IN
PC14 GPIO or low-speed oscillator input; output restrictions apply. · p. 28
4 PC15-OSC32_OUT
PC15 GPIO or low-speed oscillator output; output restrictions apply. · p. 22
5 OSC_IN
Oscillator input after reset; software can remap PD0. · p. 28
6 OSC_OUT
Oscillator output after reset; software can remap PD1. · p. 28
7 NRST
Reset pin. · p. 28
8 PC0
PC0 GPIO or ADC12_IN10. · p. 28
9 PC1
PC1 GPIO or ADC12_IN11. · p. 28
10 PC2
PC2 GPIO or ADC12_IN12. · p. 28
11 PC3
PC3 GPIO or ADC12_IN13. · p. 28
12 VSSA
Analog ground. · p. 28
13 VDDA
Analog supply. · p. 28
14 PA0-WKUP
PA0 GPIO, WKUP, USART2_CTS, ADC12_IN0 or TIM2_CH1_ETR. · p. 29
15 PA1
PA1 GPIO, USART2_RTS, ADC12_IN1 or TIM2_CH2. · p. 29
16 PA2
PA2 GPIO, USART2_TX, ADC12_IN2 or TIM2_CH3. · p. 29
17 PA3
PA3 GPIO, USART2_RX, ADC12_IN3 or TIM2_CH4. · p. 29
18 VSS_4
Ground supply pin. · p. 29
19 VDD_4
Main supply pin. · p. 29
20 PA4
PA4 GPIO, SPI1_NSS, USART2_CK or ADC12_IN4. · p. 29
21 PA5
PA5 GPIO, SPI1_SCK or ADC12_IN5. · p. 29
22 PA6
PA6 GPIO, SPI1_MISO, ADC12_IN6, TIM3_CH1 or remapped TIM1_BKIN. · p. 29
23 PA7
PA7 GPIO, SPI1_MOSI, ADC12_IN7, TIM3_CH2 or remapped TIM1_CH1N. · p. 29
24 PC4
PC4 GPIO or ADC12_IN14. · p. 29
25 PC5
PC5 GPIO or ADC12_IN15. · p. 29
26 PB0
PB0 GPIO, ADC12_IN8, TIM3_CH3 or remapped TIM1_CH2N. · p. 29
27 PB1
PB1 GPIO, ADC12_IN9, TIM3_CH4 or remapped TIM1_CH3N. · p. 29
28 PB2
5 V tolerant PB2 GPIO or BOOT1. · p. 30
29 PB10
5 V tolerant PB10 GPIO, I2C2_SCL, USART3_TX or remapped TIM2_CH3. · p. 30
30 PB11
5 V tolerant PB11 GPIO, I2C2_SDA, USART3_RX or remapped TIM2_CH4. · p. 30
31 VSS_1
Ground supply pin. · p. 30
32 VDD_1
Main supply pin. · p. 30
33 PB12
5 V tolerant PB12 GPIO, SPI2_NSS, I2C2_SMBAl, USART3_CK or TIM1_BKIN. · p. 30
34 PB13
5 V tolerant PB13 GPIO, SPI2_SCK, USART3_CTS or TIM1_CH1N. · p. 30
35 PB14
5 V tolerant PB14 GPIO, SPI2_MISO, USART3_RTS or TIM1_CH2N. · p. 30
36 PB15
5 V tolerant PB15 GPIO, SPI2_MOSI or TIM1_CH3N. · p. 30
37 PC6
5 V tolerant PC6 GPIO or remapped TIM3_CH1. · p. 31
38 PC7
5 V tolerant PC7 GPIO or remapped TIM3_CH2. · p. 31
39 PC8
5 V tolerant PC8 GPIO or remapped TIM3_CH3. · p. 31
40 PC9
5 V tolerant PC9 GPIO or remapped TIM3_CH4. · p. 31
41 PA8
5 V tolerant PA8 GPIO, USART1_CK, TIM1_CH1 or MCO. · p. 31
42 PA9
5 V tolerant PA9 GPIO, USART1_TX or TIM1_CH2. · p. 31
43 PA10
5 V tolerant PA10 GPIO, USART1_RX or TIM1_CH3. · p. 31
44 PA11
5 V tolerant PA11 GPIO, USART1_CTS, CANRX, USBDM or TIM1_CH4. · p. 31
45 PA12
5 V tolerant PA12 GPIO, USART1_RTS, CANTX, USBDP or TIM1_ETR. · p. 31
46 PA13
5 V tolerant JTMS/SWDIO after reset; remappable PA13 GPIO. · p. 31
47 VSS_2
Ground supply pin. · p. 31
48 VDD_2
Main supply pin. · p. 31
49 PA14
5 V tolerant JTCK/SWCLK after reset; remappable PA14 GPIO. · p. 32
50 PA15
5 V tolerant JTDI after reset; remappable TIM2_CH1_ETR, PA15 GPIO or SPI1_NSS. · p. 32
51 PC10
5 V tolerant PC10 GPIO or remapped USART3_TX. · p. 32
52 PC11
5 V tolerant PC11 GPIO or remapped USART3_RX. · p. 32
53 PC12
5 V tolerant PC12 GPIO or remapped USART3_CK. · p. 32
54 PD2
5 V tolerant PD2 GPIO or TIM3_ETR. · p. 32
55 PB3
5 V tolerant JTDO after reset; remappable TIM2_CH2, PB3 GPIO, TRACESWO or SPI1_SCK. · p. 32
56 PB4
5 V tolerant JNTRST after reset; remappable TIM3_CH1, PB4 GPIO or SPI1_MISO. · p. 32
57 PB5
PB5 GPIO, I2C1_SMBAl or remapped TIM3_CH2 or SPI1_MOSI. · p. 32
58 PB6
5 V tolerant PB6 GPIO, I2C1_SCL, TIM4_CH1 or remapped USART1_TX. · p. 32
59 PB7
5 V tolerant PB7 GPIO, I2C1_SDA, TIM4_CH2 or remapped USART1_RX. · p. 32
60 BOOT0
BOOT0 input. · p. 32
61 PB8
5 V tolerant PB8 GPIO, TIM4_CH3 or remapped I2C1_SCL or CANRX. · p. 33
62 PB9
5 V tolerant PB9 GPIO, TIM4_CH4 or remapped I2C1_SDA or CANTX. · p. 33
63 VSS_3
Ground supply pin. · p. 33
64 VDD_3
Main supply pin. · p. 33

Open-source boards using it

10See all 10
  • 2 layers40 × 50 mmProgArm, the printed circuit board in 3D

    ProgArm

    ProgArm/ProgArm-Hardware

    This repository contains only schematic and PCB files. Schematic PDF and Gerber files are attached to every release.

    131 parts3GPL-3.0
  • 2 layers80 × 74 mmHubble metal detector, the printed circuit board in 3D

    Hubble metal detector

    zartarn15/hubble-metal-detector

    STM32-based digital metal detector with custom hardware and embedded DSP firmware.

    156 parts2
  • 2 layers79.7 × 80 mmMainboardv1.2, the printed circuit board in 3D

    Mainboardv1.2

    doobedoobedo/Huebner_Inverter

    KiCAD port of https://github.com/jsphuebner/inverter-hardware mainboard V1.2

    133 parts1
  • 4 layers100 × 50 mmBalancing robot, the printed circuit board in 3D

    Balancing robot

    JwAhn0830/stm32_balancingRobot

    68 parts

Parts like it

8

Questions

Is there a KiCad symbol and footprint for the STM32F103RBT6?

Yes. The symbol is MCU_ST_STM32F1:STM32F103RBTx and the footprint Package_QFP:LQFP-64_10x10mm_P0.5mm, both drawn on this page. PCBKit places them on a board for you when you design with it.

What package is the STM32F103RBT6?

LQFP-64(10x10), with 64 pins. Its footprint is drawn on this page.

Where is the STM32F103RBT6 datasheet?

STMicroelectronics publishes it: the Datasheet link on this page opens it.

Where can I order the STM32F103RBT6?

JLCPCB lists it as part C8735, with 7,284 in stock; the sellers' links on this page open their listings.

What can replace the STM32F103RBT6?

Parts like it in the library: the STM32F103RCT6 by STMicroelectronics, the MSPM0G3507SPMR by Texas Instruments, the GD32F103RBT6 by GigaDevice and the GD32F103RCT6 by GigaDevice. Check their datasheets: a part that fits the footprint may still differ in its ratings.

Which open-source boards use the STM32F103RBT6?

10 boards in 10 repositories on GitHub; the most starred are listed on this page, with their KiCad files.