
STM32F030K6T6
STMicroelectronicsExtended
-40℃~+85℃ 12bit 2.4V~3.6V 26 32 Bit 32KB 48MHz 4KB ARM Cortex-M0 Built-in FLASH LQFP-32(7x7) Microcontrollers (MCU/MPU/SOC) ROHS
- Part id
- st/STM32F030K6T6
- Category
- Microcontrollers (MCU, MPU, SOC)
- Package
- LQFP-32(7x7)
- Pins
- 32
- In stock
- 39,364 at JLCPCB (C46830)
- Used on
- 12 open-source boards
Overview
The STM32F030K6T6 is a microcontroller made by STMicroelectronics in a LQFP-32(7x7) package with 32 pins. -40℃~+85℃ 12bit 2.4V~3.6V 26 32 Bit 32KB 48MHz 4KB ARM Cortex-M0 Built-in FLASH LQFP-32(7x7) Microcontrollers (MCU/MPU/SOC) ROHS.
PCBKit's library has its KiCad symbol (MCU_ST_STM32F0:STM32F030K6Tx, from KiCad's library) and its footprint (Package_QFP:LQFP-32_7x7mm_P0.8mm, from KiCad's library), ready for a KiCad board. 39,364 are in stock at JLCPCB (part C46830). 12 open-source boards in 12 repositories on GitHub use it.
Symbol
Footprint
From the datasheet
14- Supply, least
- 2.4 V · VDD, recommended operating min · p. 45
- Supply, most
- 3.6 V · VDD, recommended operating max · p. 45
- Supply, absolute maximum
- 4 V · VDD, absolute max · p. 43
- Works from
- -40 °C · Ambient min, suffix 6, maximum power dissipation · p. 45
- Works up to
- 85 °C · Ambient max, suffix 6, maximum power dissipation · p. 45
- Works up to
- 105 °C · Ambient max, suffix 6, low power dissipation, subject to junction limit · p. 45
- Junction, hottest
- 105 °C · Junction max, recommended operating, suffix 6 · p. 45
- Junction, hottest
- 150 °C · Junction absolute max · p. 44
- Takes working
- 23.46 mA · sum of VDD and VDDA typical Run currents, 48 MHz, 3.3 V, HSE crystal, peripherals enabled · p. 50
- Takes asleep
- 4.3 µA · sum of VDD and VDDA typical Standby currents, LSI and IWDG on, VDDA monitoring off, 3.6 V · p. 49
- A pin gives at most
- 25 mA · I/O or control pin absolute max sink current · p. 44
- Junction to air (LQFP32 - 7 mm x 7 mm)
- 56 K/W · Junction to ambient thermal resistance · p. 93
- Takes asleep
- 7.9 µA · sum of VDD and VDDA typical Stop currents, low-power regulator, oscillators OFF, VDDA monitoring ON, 3.6 V · p. 49
- A pin gives at most
- 20 mA · GPIO source or sink max, relaxed VOL/VOH · p. 69
What it is and has
11- Core
- ARM 32-bit Cortex-M0 CPU · p. 1
- CPU clock
- Up to 48 MHz · p. 1
- CRC
- CRC calculation unit · p. 1
- DMA
- 5-channel controller · p. 1
- Low power modes
- Sleep, Stop, Standby · p. 1
- Internal oscillator
- 40 kHz RC · p. 1
- Clock
- Up to 48 MHz · p. 1
- Package
- LQFP32 7x7 mm · p. 1
- CPU frequency
- up to 48 MHz · p. 1
- CRC calculation unit
- Present · p. 1
- ADC resolution
- 12-bit · p. 73
Around it
4- crystal 4 to 32 MHz
- between OSC_IN and OSC_OUT; Optional HSE crystal/ceramic resonator; place the resonator and load capacitors as close as possible to the oscillator pins. · p. 56
- cap 5 pF to 20 pF
- between OSC_IN and GND; CL1: high-quality ceramic capacitor for high-frequency applications, selected to match the crystal or resonator; include PCB and MCU pin capacitance when sizing. · p. 56
- crystal 32.768 kHz
- between LSE oscillator pins; Optional LSE crystal resonator; place the resonator and load capacitors as close as possible to the oscillator pins. · p. 58
- diode Schottky diode
- between standard analog input pin and ground; Recommended on standard analog pins that may inject negative current. · p. 74
Specifications
252| Parameter | Conditions | As printed | Page |
|---|---|---|---|
| External main supply voltage VDD–VSS | Absolute maximum ratings | min -0.3 · max 4 V | 43 |
| External analog supply voltage VDDA–VSS | Absolute maximum ratings | min -0.3 · max 4 V | 43 |
| Allowed voltage difference for VDD > VDDA VDD–VDDA | max 0.4 V | 43 | |
| Input voltage on TTa pins VIN | Min VSS − 0.3 | max 4 V | 43 |
| BOOT0 VIN | Max VDDIOx + 4.0; VDDIOx internally connected to VDD | min 0 V | 43 |
| Input voltage on any other pin VIN | Min VSS − 0.3 | max 4 V | 43 |
| Variations between different VDD power pins |ΔVDDx| | max 50 mV | 43 | |
| Variations between all the different ground pins |VSSx − VSS| | max 50 mV | 43 | |
| Total current into sum of all VDD power lines (source) ΣIVDD | Absolute maximum ratings | max 120 mA | 44 |
| Total current out of sum of all VSS ground lines (sink) ΣIVSS | Absolute maximum ratings | max -120 mA | 44 |
| Maximum current into each VDD power pin (source) IVDD(PIN) | Absolute maximum ratings | max 100 mA | 44 |
| Maximum current out of each VSS ground pin (sink) IVSS(PIN) | Absolute maximum ratings | max -100 mA | 44 |
| Output current sunk by any I/O and control pin IIO(PIN) | Absolute maximum ratings | max 25 mA | 44 |
| Output current source by any I/O and control pin IIO(PIN) | Absolute maximum ratings | max -25 mA | 44 |
| Total output current sunk by sum of all I/Os and control pins ΣIIO(PIN) | Absolute maximum ratings | max 80 mA | 44 |
| Total output current sourced by sum of all I/Os and control pins ΣIIO(PIN) | Absolute maximum ratings | max -80 mA | 44 |
| Injected current on FT and FTf pins IINJ(PIN) | Absolute maximum ratings; table lists -5/+0 | min -5 · max 0 mA | 44 |
| Injected current on TC and RST pin IINJ(PIN) | Absolute maximum ratings; ±5 mA | min -5 · max 5 mA | 44 |
| Injected current on TTa pins IINJ(PIN) | Absolute maximum ratings; ±5 mA | min -5 · max 5 mA | 44 |
| Total injected current (sum of all I/O and control pins) ΣIINJ(PIN) | Absolute maximum ratings; absolute sum of positive and negative injected currents | min -25 · max 25 mA | 44 |
| Storage temperature range TSTG | Absolute maximum ratings | min -65 · max 150 °C | 44 |
| Maximum junction temperature TJ | Absolute maximum ratings | max 150 °C | 44 |
| Internal AHB clock frequency fHCLK | min 0 · max 48 MHz | 45 | |
| Internal APB clock frequency fPCLK | min 0 · max 48 MHz | 45 | |
| Standard operating voltage VDD | min 2.4 · max 3.6 V | 45 | |
| Analog operating voltage VDDA | Must have a potential equal to or higher than VDD | min 2.4 · max 3.6 V | 45 |
| I/O input voltage VIN | TC and RST I/O; max VDDIOx+0.3 | min -0.3 V | 45 |
| I/O input voltage VIN | TTa I/O; max VDDA+0.3 | min -0.3 V | 45 |
| I/O input voltage VIN | FT and FTf I/O | min -0.3 · max 5.5 V | 45 |
| I/O input voltage VIN | BOOT0 | min 0 · max 5.5 V | 45 |
| Power dissipation at TA = 85 °C for suffix 6 PD | LQFP32 | max 357 mW | 45 |
| Ambient temperature for the suffix 6 version TA | Maximum power dissipation | min -40 · max 85 °C | 45 |
| Ambient temperature for the suffix 6 version TA | Low power dissipation; TJ must not exceed TJmax | min -40 · max 105 °C | 45 |
| Junction temperature range TJ | Suffix 6 version | min -40 · max 105 °C | 45 |
| VDD rise time rate tVDD | Max ∞ | min 0 us/V | 45 |
| VDD fall time rate tVDD | Max ∞ | min 20 us/V | 45 |
| VDDA rise time rate tVDDA | Max ∞ | min 0 us/V | 45 |
| VDDA fall time rate tVDDA | Max ∞ | min 20 us/V | 45 |
| Supply current in Run mode, code executing from Flash IDD | STM32F030x4/6/8; all peripherals enabled; HSI or HSE, PLL on; 48 MHz; max at 85 °C | typ 22 · max 22.8 mA | 47 |
| Supply current in Run mode, code executing from Flash IDD | STM32F030x4/6/8; all peripherals enabled; HSI or HSE, PLL on; 24 MHz; max at 85 °C | typ 12.2 · max 13.2 mA | 47 |
| Supply current in Run mode, code executing from Flash IDD | STM32F030x4/6/8; all peripherals enabled; HSI or HSE, PLL off; 8 MHz; max at 85 °C | typ 4.4 · max 5.2 mA | 47 |
| Supply current in Run mode, code executing from RAM IDD | STM32F030x4/6/8; all peripherals enabled; HSI or HSE, PLL on; 48 MHz; max at 85 °C | typ 22.2 · max 23.2 mA | 47 |
| Supply current in Run mode, code executing from RAM IDD | STM32F030x4/6/8; all peripherals enabled; HSI or HSE, PLL on; 24 MHz; max at 85 °C | typ 11.2 · max 12.2 mA | 47 |
| Supply current in Run mode, code executing from RAM IDD | STM32F030x4/6/8; all peripherals enabled; HSI or HSE, PLL off; 8 MHz; max at 85 °C | typ 4 · max 4.5 mA | 47 |
| Supply current in Sleep mode, code executing from Flash or RAM IDD | STM32F030x4/6/8; all peripherals enabled; HSI or HSE, PLL on; 48 MHz; max at 85 °C | typ 14 · max 15.3 mA | 47 |
| Supply current in Sleep mode, code executing from Flash or RAM IDD | STM32F030x4/6/8; all peripherals enabled; HSI or HSE, PLL on; 24 MHz; max at 85 °C | typ 7.3 · max 7.8 mA | 47 |
| Supply current in Sleep mode, code executing from Flash or RAM IDD | STM32F030x4/6/8; all peripherals enabled; HSI or HSE, PLL off; 8 MHz; max at 85 °C | typ 2.6 · max 2.9 mA | 47 |
| Supply current in Run mode, code executing from Flash or RAM IDDA | STM32F030x4/6/8; VDDA = 3.6 V; HSE bypass, PLL on; 48 MHz; max at 85 °C | typ 175 · max 215 uA | 48 |
| Supply current in Run mode, code executing from Flash or RAM IDDA | STM32F030x4/6/8; VDDA = 3.6 V; HSE bypass, PLL off; 8 MHz; max at 85 °C | typ 3.9 · max 4.9 uA | 48 |
| Supply current in Run mode, code executing from Flash or RAM IDDA | STM32F030x4/6/8; VDDA = 3.6 V; HSE bypass, PLL off; 1 MHz; max at 85 °C | typ 3.9 · max 4.1 uA | 48 |
| Supply current in Run mode, code executing from Flash or RAM IDDA | STM32F030x4/6/8; VDDA = 3.6 V; HSI clock, PLL on; 48 MHz; max at 85 °C | typ 244 · max 275 uA | 48 |
| Supply current in Run mode, code executing from Flash or RAM IDDA | STM32F030x4/6/8; VDDA = 3.6 V; HSI clock, PLL off; 8 MHz; max at 85 °C | typ 85 · max 105 uA | 48 |
| Supply current in Run or Sleep mode, code executing from Flash or RAM IDDA | STM32F030x4/6/8; VDDA = 3.6 V; HSE bypass, PLL on; 48 MHz; max at 85 °C | typ 174 · max 215 uA | 48 |
| Supply current in Run or Sleep mode, code executing from Flash or RAM IDDA | STM32F030x4/6/8; VDDA = 3.6 V; HSE bypass, PLL off; 8 MHz; max at 85 °C | typ 3.9 · max 4.9 uA | 48 |
| Supply current in Run or Sleep mode, code executing from Flash or RAM IDDA | STM32F030x4/6/8; VDDA = 3.6 V; HSE bypass, PLL off; 1 MHz; max at 85 °C | typ 3.9 · max 4.9 uA | 48 |
| Supply current in Run or Sleep mode, code executing from Flash or RAM IDDA | STM32F030x4/6/8; VDDA = 3.6 V; HSI clock, PLL on; 48 MHz; max at 85 °C | typ 244 · max 299 uA | 48 |
| Supply current in Run or Sleep mode, code executing from Flash or RAM IDDA | STM32F030x4/6/8; VDDA = 3.6 V; HSI clock, PLL off; 8 MHz; max at 85 °C | typ 85 · max 105 uA | 48 |
| Supply current in Stop mode IDD | VDD = VDDA = 3.6 V; regulator in run mode, all oscillators OFF; max at 85 °C | typ 19 · max 48 uA | 49 |
| Supply current in Stop mode IDD | VDD = VDDA = 3.6 V; regulator in low-power mode, all oscillators OFF; max at 85 °C | typ 5 · max 32 uA | 49 |
| Supply current in Standby mode IDD | VDD = VDDA = 3.6 V; LSI ON and IWDG ON | typ 2 uA | 49 |
| Supply current in Stop mode IDDA | VDD = VDDA = 3.6 V; VDDA monitoring ON; regulator in run or low-power mode, all oscillators OFF; max at 85 °C | typ 2.9 · max 3.5 uA | 49 |
| Supply current in Standby mode IDDA | VDD = VDDA = 3.6 V; VDDA monitoring ON; LSI ON and IWDG ON | typ 3.3 uA | 49 |
| Supply current in Standby mode IDDA | VDD = VDDA = 3.6 V; VDDA monitoring ON; LSI OFF and IWDG OFF; max at 85 °C | typ 2.8 · max 3.5 uA | 49 |
| Supply current in Stop mode IDDA | VDD = VDDA = 3.6 V; VDDA monitoring OFF; regulator in run or low-power mode, all oscillators OFF | typ 1.7 uA | 49 |
| Supply current in Standby mode IDDA | VDD = VDDA = 3.6 V; VDDA monitoring OFF; LSI ON and IWDG ON | typ 2.3 uA | 49 |
| Supply current in Standby mode IDDA | VDD = VDDA = 3.6 V; VDDA monitoring OFF; LSI OFF and IWDG OFF | typ 1.4 uA | 49 |
| Supply current in Run mode from VDD supply IDD | VDD = VDDA = 3.3 V; HSE crystal clock 8 MHz; fHCLK = 48 MHz; peripherals enabled | typ 23.3 mA | 50 |
| Supply current in Run mode from VDD supply IDD | VDD = VDDA = 3.3 V; HSE crystal clock 8 MHz; fHCLK = 48 MHz; peripherals disabled | typ 11.5 mA | 50 |
| Supply current in Run mode from VDD supply IDD | VDD = VDDA = 3.3 V; HSE crystal clock 8 MHz; fHCLK = 8 MHz; peripherals enabled | typ 4.5 mA | 50 |
| Supply current in Run mode from VDD supply IDD | VDD = VDDA = 3.3 V; HSE crystal clock 8 MHz; fHCLK = 8 MHz; peripherals disabled | typ 3 mA | 50 |
| Supply current in Run mode from VDDA supply IDDA | VDD = VDDA = 3.3 V; HSE crystal clock 8 MHz; fHCLK = 48 MHz; peripherals enabled | typ 158 uA | 50 |
| Supply current in Run mode from VDDA supply IDDA | VDD = VDDA = 3.3 V; HSE crystal clock 8 MHz; fHCLK = 48 MHz; peripherals disabled | typ 158 uA | 50 |
| Supply current in Run mode from VDDA supply IDDA | VDD = VDDA = 3.3 V; HSE crystal clock 8 MHz; fHCLK = 8 MHz; peripherals enabled | typ 2.43 uA | 50 |
| Supply current in Run mode from VDDA supply IDDA | VDD = VDDA = 3.3 V; HSE crystal clock 8 MHz; fHCLK = 8 MHz; peripherals disabled | typ 2.43 uA | 50 |
| Thermal resistance junction-ambient ΘJ | LQFP32 - 7 mm x 7 mm; table gives a single value | typ 56 °C/W | 93 |
| External main supply voltage VDD–VSS | min -0.3 · max 4 V | 43 | |
| External analog supply voltage VDDA–VSS | min -0.3 · max 4 V | 43 | |
| Allowed voltage difference for VDD > VDDA VDD–VDDA | VDD > VDDA | max 0.4 V | 43 |
| Input voltage on TTa pins VIN | max 4 V | 43 | |
| BOOT0 VIN | VDDIOx is internally connected with VDD pin | min 0 V | 43 |
| Input voltage on any other pin VIN | max 4 V | 43 | |
| Total current into sum of all VDD power lines (source) ΣIVDD | max 120 mA | 44 | |
| Total current out of sum of all VSS ground lines (sink) ΣIVSS | max -120 mA | 44 | |
| Maximum current into each VDD power pin (source) IVDD(PIN) | max 100 mA | 44 | |
| Maximum current out of each VSS ground pin (sink) IVSS(PIN) | max -100 mA | 44 | |
| Output current sunk by any I/O and control pin IIO(PIN) | max 25 mA | 44 | |
| Output current source by any I/O and control pin IIO(PIN) | max -25 mA | 44 | |
| Total output current sunk by sum of all I/Os and control pins ΣIIO(PIN) | max 80 mA | 44 | |
| Total output current sourced by sum of all I/Os and control pins ΣIIO(PIN) | max -80 mA | 44 | |
| Storage temperature range TSTG | min -65 · max 150 °C | 44 | |
| Maximum junction temperature TJ | max 150 °C | 44 | |
| I/O input voltage VIN | TC and RST I/O | min -0.3 V | 45 |
| I/O input voltage VIN | TTa I/O | min -0.3 V | 45 |
| VDD rise time rate tVDD | min 0 us/V | 45 | |
| VDD fall time rate tVDD | min 20 us/V | 45 | |
| VDDA rise time rate tVDDA | min 0 us/V | 45 | |
| VDDA fall time rate tVDDA | min 20 us/V | 45 | |
| Power on/power down reset threshold VPOR/PDR | Falling edge | min 1.8 · typ 1.88 · max 1.96 V | 46 |
| Power on/power down reset threshold VPOR/PDR | Rising edge | min 1.84 · typ 1.92 · max 2 V | 46 |
| PDR hysteresis VPDRhyst | typ 40 mV | 46 | |
| Reset temporization tRSTTEMPO | Guaranteed by design, not tested in production | min 1.5 · typ 2.5 · max 4.5 ms | 46 |
| Internal reference voltage VREFINT | –40 °C < TA < +85 °C | min 1.16 · typ 1.2 · max 1.24 V | 46 |
| ADC sampling time when reading the internal reference voltage tS_vrefint | typ 5.1 · max 17.1 us | 46 | |
| Internal reference voltage spread over the temperature range ΔVREFINT | VDDA = 3 V | max 10 mV | 46 |
| Temperature coefficient TCoeff | min -100 · max 100 ppm/°C | 46 | |
| Supply current in Run mode, code executing from Flash IDD | STM32F030x4/6/8; 48 MHz; HSI or HSE clock, PLL on; all peripherals enabled; max at TA = 85 °C | typ 22 · max 22.8 mA | 47 |
| Supply current in Run mode, code executing from Flash IDD | STM32F030x4/6/8; 24 MHz; HSI or HSE clock, PLL on; all peripherals enabled; max at TA = 85 °C | typ 12.2 · max 13.2 mA | 47 |
| Supply current in Run mode, code executing from Flash IDD | STM32F030x4/6/8; 8 MHz; HSI or HSE clock, PLL off; all peripherals enabled; max at TA = 85 °C | typ 4.4 · max 5.2 mA | 47 |
| Supply current in Run mode, code executing from RAM IDD | STM32F030x4/6/8; 48 MHz; HSI or HSE clock, PLL on; all peripherals enabled; max at TA = 85 °C | typ 22.2 · max 23.2 mA | 47 |
| Supply current in Run mode, code executing from RAM IDD | STM32F030x4/6/8; 24 MHz; HSI or HSE clock, PLL on; all peripherals enabled; max at TA = 85 °C | typ 11.2 · max 12.2 mA | 47 |
| Supply current in Run mode, code executing from RAM IDD | STM32F030x4/6/8; 8 MHz; HSI or HSE clock, PLL off; all peripherals enabled; max at TA = 85 °C | typ 4 · max 4.5 mA | 47 |
| Supply current in Sleep mode, code executing from Flash or RAM IDD | STM32F030x4/6/8; 48 MHz; HSI or HSE clock, PLL on; all peripherals enabled; max at TA = 85 °C | typ 14 · max 15.3 mA | 47 |
| Supply current in Sleep mode, code executing from Flash or RAM IDD | STM32F030x4/6/8; 24 MHz; HSI or HSE clock, PLL on; all peripherals enabled; max at TA = 85 °C | typ 7.3 · max 7.8 mA | 47 |
| Supply current in Sleep mode, code executing from Flash or RAM IDD | STM32F030x4/6/8; 8 MHz; HSI or HSE clock, PLL off; all peripherals enabled; max at TA = 85 °C | typ 2.6 · max 2.9 mA | 47 |
| Supply current in Run mode, code executing from Flash or RAM IDDA | STM32F030x4/6/8; VDDA = 3.6 V; HSE bypass, PLL on; 48 MHz; max at TA = 85 °C | typ 175 · max 215 uA | 48 |
| Supply current in Run mode, code executing from Flash or RAM IDDA | STM32F030x4/6/8; VDDA = 3.6 V; HSE bypass, PLL off; 8 MHz; max at TA = 85 °C | typ 3.9 · max 4.9 uA | 48 |
| Supply current in Run mode, code executing from Flash or RAM IDDA | STM32F030x4/6/8; VDDA = 3.6 V; HSI clock, PLL on; 48 MHz; max at TA = 85 °C | typ 244 · max 275 uA | 48 |
| Supply current in Run mode, code executing from Flash or RAM IDDA | STM32F030x4/6/8; VDDA = 3.6 V; HSI clock, PLL off; 8 MHz; max at TA = 85 °C | typ 85 · max 105 uA | 48 |
| Supply current in Run or Sleep mode, code executing from Flash or RAM IDDA | STM32F030x4/6/8; VDDA = 3.6 V; HSE bypass, PLL on; 48 MHz; max at TA = 85 °C | typ 174 · max 215 uA | 48 |
| Supply current in Run or Sleep mode, code executing from Flash or RAM IDDA | STM32F030x4/6/8; VDDA = 3.6 V; HSE bypass, PLL off; 8 MHz; max at TA = 85 °C | typ 3.9 · max 4.9 uA | 48 |
| Supply current in Run or Sleep mode, code executing from Flash or RAM IDDA | STM32F030x4/6/8; VDDA = 3.6 V; HSE bypass, PLL off; 1 MHz; max at TA = 85 °C | typ 3.9 · max 4.9 uA | 48 |
| Supply current in Run or Sleep mode, code executing from Flash or RAM IDDA | STM32F030x4/6/8; VDDA = 3.6 V; HSI clock, PLL on; 48 MHz; max at TA = 85 °C | typ 244 · max 299 uA | 48 |
| Supply current in Run or Sleep mode, code executing from Flash or RAM IDDA | STM32F030x4/6/8; VDDA = 3.6 V; HSI clock, PLL off; 8 MHz; max at TA = 85 °C | typ 85 · max 105 uA | 48 |
| Supply current in Stop mode IDD | VDD = VDDA = 3.6 V; regulator in run mode, all oscillators OFF; max at TA = 85 °C | typ 19 · max 48 uA | 49 |
| Supply current in Stop mode IDD | VDD = VDDA = 3.6 V; regulator in low-power mode, all oscillators OFF; max at TA = 85 °C | typ 5 · max 32 uA | 49 |
| Supply current in Standby mode IDDA | VDD = VDDA = 3.6 V; VDDA monitoring ON; LSI OFF and IWDG OFF; max at TA = 85 °C | typ 2.8 · max 3.5 uA | 49 |
| Supply current in Run mode from VDD supply IDD | VDD = VDDA = 3.3 V; HSE crystal clock 8 MHz; 48 MHz fHCLK; PLL used; peripherals enabled | typ 23.3 mA | 50 |
| Supply current in Run mode from VDD supply IDD | VDD = VDDA = 3.3 V; HSE crystal clock 8 MHz; 48 MHz fHCLK; PLL used; peripherals disabled | typ 11.5 mA | 50 |
| Supply current in Run mode from VDD supply IDD | VDD = VDDA = 3.3 V; HSE crystal clock 8 MHz; 8 MHz fHCLK; peripherals enabled | typ 4.5 mA | 50 |
| Supply current in Run mode from VDD supply IDD | VDD = VDDA = 3.3 V; HSE crystal clock 8 MHz; 8 MHz fHCLK; peripherals disabled | typ 3 mA | 50 |
| Supply current in Run mode from VDDA supply IDDA | VDD = VDDA = 3.3 V; HSE crystal clock 8 MHz; 48 MHz fHCLK; PLL used; peripherals enabled | typ 158 uA | 50 |
| Supply current in Run mode from VDDA supply IDDA | VDD = VDDA = 3.3 V; HSE crystal clock 8 MHz; 48 MHz fHCLK; PLL used; peripherals disabled | typ 158 uA | 50 |
| Supply current in Run mode from VDDA supply IDDA | VDD = VDDA = 3.3 V; HSE crystal clock 8 MHz; 8 MHz fHCLK; peripherals enabled | typ 2.43 uA | 50 |
| Supply current in Run mode from VDDA supply IDDA | VDD = VDDA = 3.3 V; HSE crystal clock 8 MHz; 8 MHz fHCLK; peripherals disabled | typ 2.43 uA | 50 |
| I/O current consumption ISW | VDDIOx = 3.3 V, CEXT = 0 pF, C = CINT + CEXT+ CS, fSW = 4 MHz | typ 0.18 mA | 52 |
| I/O current consumption ISW | VDDIOx = 3.3 V, CEXT = 0 pF, C = CINT + CEXT+ CS, fSW = 8 MHz | typ 0.37 mA | 52 |
| I/O current consumption ISW | VDDIOx = 3.3 V, CEXT = 0 pF, C = CINT + CEXT+ CS, fSW = 16 MHz | typ 0.76 mA | 52 |
| I/O current consumption ISW | VDDIOx = 3.3 V, CEXT = 0 pF, C = CINT + CEXT+ CS, fSW = 24 MHz | typ 1.39 mA | 52 |
| I/O current consumption ISW | VDDIOx = 3.3 V, CEXT = 0 pF, C = CINT + CEXT+ CS, fSW = 48 MHz | typ 2.188 mA | 52 |
| I/O current consumption ISW | VDDIOx = 3.3 V, CEXT = 22 pF, C = CINT + CEXT+ CS, fSW = 4 MHz | typ 0.49 mA | 52 |
| I/O current consumption ISW | VDDIOx = 3.3 V, CEXT = 22 pF, C = CINT + CEXT+ CS, fSW = 8 MHz | typ 0.94 mA | 52 |
| I/O current consumption ISW | VDDIOx = 3.3 V, CEXT = 22 pF, C = CINT + CEXT+ CS, fSW = 16 MHz | typ 2.38 mA | 52 |
| I/O current consumption ISW | VDDIOx = 3.3 V, CEXT = 22 pF, C = CINT + CEXT+ CS, fSW = 24 MHz | typ 3.99 mA | 52 |
| I/O current consumption ISW | VDDIOx = 3.3 V, CEXT = 47 pF, fSW = 4 MHz | typ 0.81 mA | 52 |
| I/O current consumption ISW | VDDIOx = 3.3 V, CEXT = 47 pF, fSW = 8 MHz | typ 1.7 mA | 52 |
| I/O current consumption ISW | VDDIOx = 3.3 V, CEXT = 47 pF, fSW = 16 MHz | typ 3.67 mA | 52 |
| Wakeup from Stop mode tWUSTOP | Regulator in run mode; typical at VDD = VDDA = 3.3 V | typ 2.8 · max 5 us | 53 |
| Wakeup from Standby mode tWUSTANDBY | Typical at VDD = VDDA = 3.3 V | typ 51 us | 53 |
| Wakeup from Sleep mode tWUSLEEP | Typical at VDD = VDDA = 3.3 V; 4 SYSCLK cycles | typ 4 SYSCLK cycles | 53 |
| Oscillator frequency fOSC_IN | min 4 · typ 8 · max 32 MHz | 56 | |
| Feedback resistor RF | typ 200 kΩ | 56 | |
| HSE current consumption IDD | During startup | max 8.5 mA | 56 |
| HSE current consumption IDD | VDD = 3.3 V, Rm = 45 Ω, CL = 10 pF@8 MHz | typ 0.5 mA | 56 |
| HSE current consumption IDD | VDD = 3.3 V, Rm = 30 Ω, CL = 20 pF@32 MHz | typ 1.5 mA | 56 |
| Oscillator transconductance gm | Startup | min 10 mA/V | 56 |
| Startup time tSU(HSE) | VDD is stabilized | typ 2 ms | 56 |
| LSE current consumption IDD | LSEDRV[1:0]=00, lower driving capability | typ 0.5 · max 0.9 uA | 58 |
| LSE current consumption IDD | LSEDRV[1:0]= 01, medium low driving capability | max 1 uA | 58 |
| LSE current consumption IDD | LSEDRV[1:0] = 10, medium high driving capability | max 1.3 uA | 58 |
| LSE current consumption IDD | LSEDRV[1:0]=11, higher driving capability | max 1.6 uA | 58 |
| Oscillator transconductance gm | LSEDRV[1:0]=00, lower driving capability | min 5 uA/V | 58 |
| Oscillator transconductance gm | LSEDRV[1:0]= 01, medium low driving capability | min 8 uA/V | 58 |
| Oscillator transconductance gm | LSEDRV[1:0] = 10, medium high driving capability | min 15 uA/V | 58 |
| Oscillator transconductance gm | LSEDRV[1:0]=11, higher driving capability | min 25 uA/V | 58 |
| Startup time tSU(LSE) | VDDIOx is stabilized | typ 2 s | 58 |
| 16-bit programming time tprog | TA = -40 to +85 °C | typ 53.5 us | 62 |
| Page erase time tERASE | TA = -40 to +85 °C; STM32F030x6 page size is 1KB | typ 30 ms | 62 |
| Mass erase time tME | TA = -40 to +85 °C | typ 30 ms | 62 |
| Supply current IDD | Write mode; TA = -40 to +85 °C | max 10 mA | 62 |
| Supply current IDD | Erase mode; TA = -40 to +85 °C | max 12 mA | 62 |
| Programming voltage Vprog | TA = -40 to +85 °C | min 2.4 · max 3.6 V | 62 |
| Endurance NEND | TA = -40 to +85 °C | min 1 kcycles | 62 |
| Data retention tRET | 1 kcycle at TA = 85 °C | min 20 Years | 62 |
| Electrostatic discharge voltage (human body model) VESD(HBM) | TA = +25 °C, conforming to JESD22-A114; All packages; Class 2 | max 2000 V | 64 |
| Electrostatic discharge voltage (charge device model) VESD(CDM) | TA = +25 °C, conforming to ANSI/ESD STM5.3.1; All packages; Class II | max 500 V | 64 |
| Injected current on BOOT0 and PF1 pins IINJ | Functional susceptibility: negative injection -0 mA; positive injection NA | min 0 mA | 65 |
| Injected current on PA9, PB3, PB13, PF11 pins with induced leakage current on adjacent pins less than 50 uA IINJ | Functional susceptibility: negative injection -5 mA; positive injection NA | min -5 mA | 65 |
| Injected current on PA11 and PA12 pins with induced leakage current on adjacent pins less than -1 mA IINJ | Functional susceptibility: negative injection -5 mA; positive injection NA | min -5 mA | 65 |
| Injected current on PB0 and PB1 pins IINJ | Functional susceptibility: negative injection -5 mA; positive injection NA | min -5 mA | 65 |
| Injected current on all other TTa, TC and RST pins IINJ | Functional susceptibility: negative and positive injection | min -5 · max 5 mA | 65 |
| Output low level voltage for an I/O pin VOL | |IIO| = 8 mA, VDDIOx ≥ 2.7 V | max 0.4 V | 69 |
| Output low level voltage for an I/O pin VOL | |IIO| = 20 mA, VDDIOx ≥ 2.7 V | max 1.3 V | 69 |
| Output low level voltage for an I/O pin VOL | |IIO| = 6 mA | max 0.4 V | 69 |
| Output low level voltage for an FTf I/O pin in Fm+ mode VOLFm+ | |IIO| = 20 mA, VDDIOx ≥ 2.7 V | max 0.4 V | 69 |
| Output low level voltage for an FTf I/O pin in Fm+ mode VOLFm+ | |IIO| = 10 mA | max 0.4 V | 69 |
| Maximum frequency fmax(IO)out | OSPEEDRy[1:0] = x0, CL = 50 pF, VDDIOx ≥ 2.4 V | max 2 MHz | 70 |
| Output fall time tf(IO)out | OSPEEDRy[1:0] = x0, CL = 50 pF, VDDIOx ≥ 2.4 V | max 125 ns | 70 |
| Output rise time tr(IO)out | OSPEEDRy[1:0] = x0, CL = 50 pF, VDDIOx ≥ 2.4 V | max 125 ns | 70 |
| Maximum frequency fmax(IO)out | OSPEEDRy[1:0] = 01, CL = 50 pF, VDDIOx ≥ 2.4 V | max 10 MHz | 70 |
| Output fall time tf(IO)out | OSPEEDRy[1:0] = 01, CL = 50 pF, VDDIOx ≥ 2.4 V | max 25 ns | 70 |
| Output rise time tr(IO)out | OSPEEDRy[1:0] = 01, CL = 50 pF, VDDIOx ≥ 2.4 V | max 25 ns | 70 |
| Maximum frequency fmax(IO)out | OSPEEDRy[1:0] = 11, CL = 30 pF, VDDIOx ≥ 2.7 V | max 50 MHz | 70 |
| Maximum frequency fmax(IO)out | OSPEEDRy[1:0] = 11, CL = 50 pF, VDDIOx ≥ 2.7 V | max 30 MHz | 70 |
| Maximum frequency fmax(IO)out | OSPEEDRy[1:0] = 11, CL = 50 pF, 2.4 V ≤ VDDIOx < 2.7 V | max 20 MHz | 70 |
| Output fall time tf(IO)out | OSPEEDRy[1:0] = 11, CL = 30 pF, VDDIOx ≥ 2.7 V | max 5 ns | 70 |
| Output fall time tf(IO)out | OSPEEDRy[1:0] = 11, CL = 50 pF, VDDIOx ≥ 2.7 V | max 8 ns | 70 |
| Output fall time tf(IO)out | OSPEEDRy[1:0] = 11, CL = 50 pF, 2.4 V ≤ VDDIOx < 2.7 V | max 12 ns | 70 |
| Output rise time tr(IO)out | OSPEEDRy[1:0] = 11, CL = 30 pF, VDDIOx ≥ 2.7 V | max 5 ns | 70 |
| Output rise time tr(IO)out | OSPEEDRy[1:0] = 11, CL = 50 pF, VDDIOx ≥ 2.7 V | max 8 ns | 70 |
| Output rise time tr(IO)out | OSPEEDRy[1:0] = 11, CL = 50 pF, 2.4 V ≤ VDDIOx < 2.7 V | max 12 ns | 70 |
| Maximum frequency fmax(IO)out | Fm+ configuration, CL = 50 pF, VDDIOx ≥ 2.4 V | max 2 MHz | 70 |
| Output fall time tf(IO)out | Fm+ configuration, CL = 50 pF, VDDIOx ≥ 2.4 V | max 12 ns | 70 |
| Output rise time tr(IO)out | Fm+ configuration, CL = 50 pF, VDDIOx ≥ 2.4 V | max 34 ns | 70 |
| Pulse width of external signals detected by the EXTI controller tEXTIpw | min 10 ns | 70 | |
| Analog supply voltage for ADC ON VDDA | min 2.4 · max 3.6 V | 73 | |
| Current consumption of the ADC IDDA (ADC) | VDD = VDDA = 3.3 V | typ 0.9 mA | 73 |
| ADC clock frequency fADC | min 0.6 · max 14 MHz | 73 | |
| Sampling rate fS | min 0.05 · max 1 MHz | 73 | |
| External trigger frequency fTRIG | fADC = 14 MHz | max 823 kHz | 73 |
| External trigger frequency fTRIG | max 17 1/fADC | 73 | |
| Conversion voltage range VAIN | Maximum VDDA | min 0 V | 73 |
| External input impedance RAIN | See Equation 1 and Table 51 for details | max 50 kΩ | 73 |
| Sampling switch resistance RADC | max 1 kΩ | 73 | |
| Internal sample and hold capacitor CADC | max 8 pF | 73 | |
| Calibration time tCAL | fADC = 14 MHz | typ 5.9 us | 73 |
| Calibration time tCAL | typ 83 1/fADC | 73 | |
| ADC_DR register write latency WLATENCY | ADC clock = PCLK/2 | typ 4.5 fPCLK cycle | 73 |
| ADC_DR register write latency WLATENCY | ADC clock = PCLK/4 | typ 8.5 fPCLK cycle | 73 |
| Trigger conversion latency tlatr | fADC = fPCLK/2 = 14 MHz | typ 0.196 us | 73 |
| Trigger conversion latency tlatr | fADC = fPCLK/2 | typ 5.5 1/fPCLK | 73 |
| Trigger conversion latency tlatr | fADC = fPCLK/4 = 12 MHz | typ 0.219 us | 73 |
| Trigger conversion latency tlatr | fADC = fPCLK/4 | typ 10.5 1/fPCLK | 73 |
| Trigger conversion latency tlatr | fADC = fHSI14 = 14 MHz | min 0.188 · max 0.259 us | 73 |
| ADC jitter on trigger conversion JitterADC | fADC = fHSI14 | typ 1 1/fHSI14 | 73 |
| Sampling time tS | fADC = 14 MHz | min 0.107 · max 17.1 us | 73 |
| Sampling time tS | min 1.5 · max 239.5 1/fADC | 73 | |
| Power-up time tSTAB | min 0 · typ 0 · max 1 us | 74 | |
| Total conversion time (including sampling time) tCONV | fADC = 14 MHz | min 1 · max 18 us | 74 |
| Total conversion time (including sampling time) tCONV | tS for sampling +12.5 for successive approximation | min 14 · max 252 1/fADC | 74 |
| RAIN max RAIN | Ts = 1.5 cycles, tS = 0.11 us | max 0.4 kΩ | 74 |
| RAIN max RAIN | Ts = 7.5 cycles, tS = 0.54 us | max 5.9 kΩ | 74 |
| RAIN max RAIN | Ts = 13.5 cycles, tS = 0.96 us | max 11.4 kΩ | 74 |
| RAIN max RAIN | Ts = 28.5 cycles, tS = 2.04 us | max 25.2 kΩ | 74 |
| RAIN max RAIN | Ts = 41.5 cycles, tS = 2.96 us | max 37.2 kΩ | 74 |
| RAIN max RAIN | Ts = 55.5 cycles, tS = 3.96 us | max 50 kΩ | 74 |
| Total unadjusted error ET | fPCLK = 48 MHz, fADC = 14 MHz, RAIN < 10 kΩ, VDDA = 2.7 V to 3.6 V, TA = −40 to 85 °C; typical ±3.3, maximum ±4 | typ 3.3 · max 4 LSB | 74 |
| Offset error EO | fPCLK = 48 MHz, fADC = 14 MHz, RAIN < 10 kΩ, VDDA = 2.7 V to 3.6 V, TA = −40 to 85 °C; typical ±1.9, maximum ±2.8 | typ 1.9 · max 2.8 LSB | 74 |
| Gain error EG | fPCLK = 48 MHz, fADC = 14 MHz, RAIN < 10 kΩ, VDDA = 2.7 V to 3.6 V, TA = −40 to 85 °C; typical ±2.8, maximum ±3 | typ 2.8 · max 3 LSB | 74 |
| Differential linearity error ED | fPCLK = 48 MHz, fADC = 14 MHz, RAIN < 10 kΩ, VDDA = 2.7 V to 3.6 V, TA = −40 to 85 °C; typical ±0.7, maximum ±1.3 | typ 0.7 · max 1.3 LSB | 74 |
| Integral linearity error EL | fPCLK = 48 MHz, fADC = 14 MHz, RAIN < 10 kΩ, VDDA = 2.7 V to 3.6 V, TA = −40 to 85 °C; typical ±1.2, maximum ±1.7 | typ 1.2 · max 1.7 LSB | 74 |
| Timeout period | Prescaler divider /4, PR[2:0] = 0; minimum RL[11:0] = 0x000, maximum RL[11:0] = 0xFFF | min 0.1 · max 409.6 ms | 77 |
| Timeout period | Prescaler divider /8, PR[2:0] = 1; minimum RL[11:0] = 0x000, maximum RL[11:0] = 0xFFF | min 0.2 · max 819.2 ms | 77 |
| Timeout period | Prescaler divider /16, PR[2:0] = 2; minimum RL[11:0] = 0x000, maximum RL[11:0] = 0xFFF | min 0.4 · max 1638.4 ms | 77 |
| Timeout period | Prescaler divider /32, PR[2:0] = 3; minimum RL[11:0] = 0x000, maximum RL[11:0] = 0xFFF | min 0.8 · max 3276.8 ms | 77 |
| Timeout period | Prescaler divider /64, PR[2:0] = 4; minimum RL[11:0] = 0x000, maximum RL[11:0] = 0xFFF | min 1.6 · max 6553.6 ms | 77 |
| Timeout period | Prescaler divider /128, PR[2:0] = 5; minimum RL[11:0] = 0x000, maximum RL[11:0] = 0xFFF | min 3.2 · max 13107.2 ms | 77 |
| Timeout period | Prescaler divider /256, PR[2:0] = 6 or 7; minimum RL[11:0] = 0x000, maximum RL[11:0] = 0xFFF | min 6.4 · max 26214.4 ms | 77 |
| Timeout value | Prescaler 1, WDGTB = 0 | min 0.0853 · max 5.4613 ms | 77 |
| Timeout value | Prescaler 2, WDGTB = 1 | min 0.1706 · max 10.9226 ms | 77 |
| Timeout value | Prescaler 4, WDGTB = 2 | min 0.3413 · max 21.8453 ms | 77 |
| Timeout value | Prescaler 8, WDGTB = 3 | min 0.6826 · max 43.6906 ms | 77 |
| Thermal resistance junction-ambient ΘJ | LQFP32 - 7 mm x 7 mm | typ 56 °C/W | 93 |
Pins, by the datasheet
28- 4 NRST
- Active-low device reset input and internal reset output. · p. 28
- 5 VDDA
- Analog power supply. · p. 28
- 6 PA0
- GPIO with USART1_CTS, ADC_IN0, RTC_TAMP2 and WKUP1 functions. · p. 28
- 7 PA1
- GPIO with USART1_RTS, EVENTOUT and ADC_IN1 functions. · p. 28
- 8 PA2
- GPIO with USART1_TX and ADC_IN2 functions. · p. 29
- 9 PA3
- GPIO with USART1_RX and ADC_IN3 functions. · p. 29
- 10 PA4
- GPIO with SPI1_NSS, USART1_CK, TIM14_CH1 and ADC_IN4 functions. · p. 29
- 11 PA5
- GPIO with SPI1_SCK and ADC_IN5 functions. · p. 29
- 12 PA6
- GPIO with SPI1_MISO, TIM3_CH1, TIM1_BKIN, TIM16_CH1, EVENTOUT and ADC_IN6 functions. · p. 29
- 13 PA7
- GPIO with SPI1_MOSI, TIM3_CH2, TIM14_CH1, TIM1_CH1N, TIM17_CH1, EVENTOUT and ADC_IN7 functions. · p. 29
- 14 PB0
- GPIO with TIM3_CH3, TIM1_CH2N, EVENTOUT and ADC_IN8 functions. · p. 29
- 1 VDD
- Digital power supply. · p. 33
- 15 PB1
- GPIO with TIM3_CH4, TIM14_CH1, TIM1_CH3N and ADC_IN9 functions. · p. 30
- 16 VSS
- Ground. · p. 30
- 17 VDD
- Digital power supply. · p. 30
- 18 PA8
- GPIO with USART1_CK, TIM1_CH1, EVENTOUT and MCO functions. · p. 31
- 19 PA9
- GPIO with USART1_TX and TIM1_CH2 functions. · p. 31
- 20 PA10
- GPIO with USART1_RX, TIM1_CH3 and TIM17_BKIN functions. · p. 31
- 21 PA11
- GPIO with USART1_CTS, TIM1_CH4 and EVENTOUT functions. · p. 31
- 22 PA12
- GPIO with USART1_RTS, TIM1_ETR and EVENTOUT functions. · p. 31
- 25 PA15
- GPIO with SPI1_NSS, USART1_RX and EVENTOUT functions. · p. 31
- 26 PB3
- GPIO with SPI1_SCK and EVENTOUT functions. · p. 32
- 27 PB4
- GPIO with SPI1_MISO, TIM3_CH1 and EVENTOUT functions. · p. 32
- 28 PB5
- GPIO with SPI1_MOSI, I2C1_SMBA, TIM16_BKIN and TIM3_CH2 functions. · p. 32
- 29 PB6
- GPIO with I2C1_SCL, USART1_TX and TIM16_CH1N functions. · p. 32
- 30 PB7
- GPIO with I2C1_SDA, USART1_RX and TIM17_CH1N functions. · p. 32
- 31 BOOT0
- Boot memory selection. · p. 32
- 32 VSS
- Ground. · p. 33
- 4 layers243.8 × 171.5 mm

- 2 layers22 × 41 mm

RSTM32F030K6T6
r-pv/STM32F030K6
Custom board for the STM32F30K6T6 MCU, compatible with STM32Duino (Arduino).
23 parts11GPL-3.0 - 2 layers59.1 × 110.7 mm

- 4 layers243.8 × 245.5 mm

Neotron Common Hardware
Neotron-Compute/Neotron-Common-Hardware
Contains KiCad footprints and symbols shared across multiple Neotron projects.
287 parts4CC-BY-SA-4.0 - 2 layers50 × 36 mm

- 2 layers80 × 56 mm

- 2 layers75 × 50 mm

- 2 layers105 × 50 mm

Parts like it
8STM32G030K6T6
LQFP-32(7x7)-40℃~+85℃ 12bit 2V~3.6V 30 32 Bit 32KB 64MHz 8KB ARM Cortex-M0+ Built-in+External FLASH LQFP-32(7x7) Microcontrollers (MCU/MPU/SOC) ROHSSTMicroelectronicsMicrocontrollers (MCU/MPU/SOC)APM32F030K6T6
LQFP-32(7x7)12bit 26 2V~3.6V 32 Bit 32KB 48MHz ARM Cortex-M0+ FLASH LQFP-32(7x7) Microcontrollers (MCU/MPU/SOC) ROHSGeehyMicrocontrollers (MCU/MPU/SOC)PY32F030K18T6
LQFP-32(7x7)64KB FLASH LQFP-32(7x7) Microcontrollers (MCU/MPU/SOC) ROHSPUYAMicrocontrollers (MCU/MPU/SOC)C8051F410-GQR
LQFP-32(7x7)-40℃~+85℃ 12bit 12bit 2.25KB 24 2V~5.25V 32KB 50MHz 51 Family 8 Bit Built-in FLASH LQFP-32(7x7) Microcontrollers (MCU/MPU/SOC) ROHSSilicon LabsMicrocontrollers (MCU/MPU/SOC)STM32G070KBT6
LQFP-32(7x7)-40℃~+85℃ 128KB 12bit 29 2V~3.6V 32 Bit 36KB 64MHz ARM Cortex-M0+ Built-in+External FLASH LQFP-32(7x7) Microcontrollers (MCU/MPU/SOC) ROHSSTMicroelectronicsMicrocontrollers (MCU/MPU/SOC)STM32C031K6T6
LQFP-32(7x7)-40℃~+85℃ 12KB 12bit 2V~3.6V 30 32 Bit 32KB 48MHz ARM Cortex-M0+ Built-in+External FLASH LQFP-32(7x7) Microcontrollers (MCU/MPU/SOC) ROHSSTMicroelectronicsMicrocontrollers (MCU/MPU/SOC)AC33M3064TLBN-01
LQFP-32(7x7)LQFP-32(7x7) Microcontrollers (MCU/MPU/SOC) ROHSABOV SemiconMicrocontrollers (MCU/MPU/SOC)AT32F421K8T7
LQFP-32(7x7)-40℃~+105℃ 120MHz 16KB 2.4V~3.6V 25 32 Bit 64KB ARM Cortex-M4 Built-in+External FLASH LQFP-32(7x7) Microcontrollers (MCU/MPU/SOC) ROHSARTERYMicrocontrollers (MCU/MPU/SOC)
Questions
Is there a KiCad symbol and footprint for the STM32F030K6T6?
Yes. The symbol is MCU_ST_STM32F0:STM32F030K6Tx and the footprint Package_QFP:LQFP-32_7x7mm_P0.8mm, both drawn on this page. PCBKit places them on a board for you when you design with it.
What package is the STM32F030K6T6?
LQFP-32(7x7), with 32 pins. Its footprint is drawn on this page.
Where is the STM32F030K6T6 datasheet?
STMicroelectronics publishes it: the Datasheet link on this page opens it.
Where can I order the STM32F030K6T6?
JLCPCB lists it as part C46830, with 39,364 in stock; the sellers' links on this page open their listings.
What can replace the STM32F030K6T6?
Parts like it in the library: the STM32G030K6T6 by STMicroelectronics, the APM32F030K6T6 by Geehy, the PY32F030K18T6 by PUYA and the C8051F410-GQR by Silicon Labs. Check their datasheets: a part that fits the footprint may still differ in its ratings.
Which open-source boards use the STM32F030K6T6?
12 boards in 12 repositories on GitHub; the most starred are listed on this page, with their KiCad files.