Skip to the content

QMC5883P

QSTExtended

-40℃~+85℃ 16bit 2.5V~3.6V 35uA I2C ±3mT ±3mT LGA-16(3x3) 3D Magnetic Sensors ROHS

Part id
qst/QMC5883P
Category
3D Magnetic Sensors
Package
LGA-16(3x3)
Pins
16
In stock
4,017 at JLCPCB (C2847467)
Used on
11 open-source boards

Overview

The QMC5883P is a 3D Magnetic Sensor made by QST in a LGA-16(3x3) package with 16 pins. -40℃~+85℃ 16bit 2.5V~3.6V 35uA I2C ±3mT ±3mT LGA-16(3x3) 3D Magnetic Sensors ROHS.

PCBKit's library has its KiCad symbol (EasyEDA_Cloud:QMC5883P, from EasyEDA) and its footprint (EasyEDA_Cloud:LGA-16_L3.0-W3.0-P0.50-BL_SQ, from EasyEDA), ready for a KiCad board. 4,017 are in stock at JLCPCB (part C2847467). 11 open-source boards in 9 repositories on GitHub use it.

Symbol

1SCK2VDD3NC4NC5NC6NC7NC8NC9GND10C111GND12NC13NC14NC15NC16SDA
EasyEDA_Cloud:QMC5883PFrom EasyEDA

Footprint

EasyEDA_Cloud:LGA-16_L3.0-W3.0-P0.50-BL_SQFrom EasyEDA

From the datasheet

10
Supply, least
2.5 V · VDD, recommended operating min · p. 4
Supply, most
3.6 V · VDD, recommended operating max · p. 4
Supply, absolute maximum
5.4 V · VDD, absolute max · p. 5
Works from
-40 °C · Operating temperature min · p. 4
Works up to
85 °C · Operating temperature max · p. 4
Takes working
280 µA · VDD, normal mode typical, ODR=200Hz, low power, OSR1=1 · p. 4
Takes working
1.18 mA · VDD, normal mode typical, ODR=200Hz, high power, OSR1=8 · p. 4
Takes at most
2.2 mA · VDD, continuous mode typical at maximum ODR 1500Hz · p. 4
Takes asleep
22 µA · VDD, suspend mode typical · p. 4
Data rate, most
400 kbit/s · I2C Fast-mode clock frequency max · p. 12

What it is and has

9
Sensor
3-axis single-chip magnetic sensor · p. 1
Package
16-pin LGA, 3.0x3.0x0.9mm3 · p. 1
ADC
16-bit · p. 1
Magnetic field range
±30 Gauss · p. 1
Temperature compensation
Temperature compensated data output · p. 1
I2C
Standard and Fast modes · p. 1
Data output rate
Maximum 1.5KHz · p. 1
Self-test
Built-in · p. 1
Package compliance
Lead free, RoHS · p. 1

Specifications

60
ParameterConditionsAs printedPage
Supply VoltageVDD; tested and specified at 25°Cmin 2.5 · max 3.6 V4
Suspend Mode CurrentTotal Current on VDD; 25°Ctyp 22 uA4
Normal Mode Current [1]Low power mode, OSR1=1; ODR=10Hz; 25°Ctyp 35 uA4
Normal Mode Current [1]High power mode, OSR1=8; ODR=10Hz; 25°Ctyp 78 uA4
Normal Mode Current [1]Low power mode, OSR1=1; ODR=50Hz; 25°Ctyp 85 uA4
Normal Mode Current [1]High power mode, OSR1=8; ODR=50Hz; 25°Ctyp 310 uA4
Normal Mode Current [1]Low power mode, OSR1=1; ODR=100Hz; 25°Ctyp 150 uA4
Normal Mode Current [1]High power mode, OSR1=8; ODR=100Hz; 25°Ctyp 600 uA4
Normal Mode Current [1]Low power mode, OSR1=1; ODR=200Hz; 25°Ctyp 280 uA4
Normal Mode Current [1]High power mode, OSR1=8; ODR=200Hz; 25°Ctyp 1180 uA4
Continuous Mode CurrentMaximum ODR: 1500Hz; 25°Ctyp 2200 uA4
Sensor Field RangeFull Scale; 25°Cmin -30 · max 30 Gauss4
Sensitivity [2]Field Range = ±30G; calibrated at zero field; 25°Ctyp 1000 LSB/G4
Sensitivity [2]Field Range = ±12G; calibrated at zero field; 25°Ctyp 2500 LSB/G4
Sensitivity [2]Field Range = ±8G; calibrated at zero field; 25°Ctyp 3750 LSB/G4
Sensitivity [2]Field Range = ±2G; calibrated at zero field; 25°Ctyp 15000 LSB/G4
LinearityField Range = ±30G; Happlied= ±15G; 25°Ctyp 0.5 %FS4
Hysteresis3 sweeps across ±30G; 25°Ctyp 0.03 %FS4
Digital ResolutionField Range = ±30G; 25°Ctyp 1 mGauss4
Field ResolutionStandard deviation; X/Y axis; 25°Ctyp 2 mGauss4
Field ResolutionStandard deviation; Z axis; 25°Ctyp 3 mGauss4
Operating Temperaturemin -40 · max 85 °C4
ESDHBM; 25°Cmin 4000 V4
ESDCDM; 25°Cmin 1000 V4
VDDTested at 25°Cmin -0.3 · max 5.4 V5
Storage Temperaturemin -40 · max 125 °C5
Exposed to Magnetic Field (all directions)Tested at 25°Cmax 50000 Gauss5
Hysteresis of Schmitt Trigger Input VHYSVDDIO=3.3Vmin 0.1 V5
Input Leakage, ALL Inputs IILVDDIO=3.3Vmin -10 · max 10 uA5
POR Completion Time PORTTime Period After VDD at Operating Voltage to Ready for I2C Commandmax 250 uS9
Power off Voltage SDVVoltage that Device Considered to be Power Down.max 0.2 V9
Power on Interval PINTTime Period Required for Voltage Lower Than SDV to Enable Next PORmin 100 uS9
SCL clock frequency fSCLStandard-modemin 0 · max 100 kHz12
SCL clock frequency fSCLFast-modemin 0 · max 400 kHz12
hold time (repeated) START condition tHD;STAStandard-mode; After this period, the first clock pulse is generated.min 4 uS12
hold time (repeated) START condition tHD;STAFast-mode; After this period, the first clock pulse is generated.min 0.6 uS12
LOW period of the SCL clock tLOWStandard-modemin 4.7 uS12
LOW period of the SCL clock tLOWFast-modemin 1.3 uS12
HIGH period of the SCL clock tHIGHStandard-modemin 4 uS12
HIGH period of the SCL clock tHIGHFast-modemin 0.6 uS12
set-up time for a repeated START condition tSU;STAStandard-modemin 4.7 uS12
set-up time for a repeated START condition tSU;STAFast-modemin 0.6 uS12
data hold time tHD;DATStandard-modemin 0 uS12
data hold time tHD;DATFast-modemin 0 uS12
data set-up time tSU;DATStandard-modemin 250 nS12
data set-up time tSU;DATFast-modemin 100 nS12
rise time of both SDA and SCL signals trStandard-modemax 300 nS12
rise time of both SDA and SCL signals trFast-modemax 300 nS12
fall time of both SDA and SCL signals tfStandard-modemax 300 nS12
fall time of both SDA and SCL signals tfFast-modemax 300 nS12
set-up time for STOP condition tSU;STOStandard-modemin 4 uS12
set-up time for STOP condition tSU;STOFast-modemin 0.6 uS12
bus free time between a STOP and START condition tBUFStandard-modemin 4.7 uS12
bus free time between a STOP and START condition tBUFFast-modemin 1.3 uS12
capacitive load for each bus line CbStandard-modemax 200 pF12
capacitive load for each bus line CbFast-modemax 200 pF12
data valid time tVD;DATStandard-modemax 0.8 uS12
data valid time tVD;DATFast-modemax 0.8 uS12
data valid acknowledge time tVD;ACKStandard-modemax 0.8 uS12
data valid acknowledge time tVD;ACKFast-modemax 0.8 uS12

Ordering codes, by the datasheet

1
QMC5883P-TR
LGA-16 · -40°C to 85°C operating temperature; tape and reel, 3k pieces/reel · p. 17

Open-source boards using it

11See all 11
  • 2 layers94 × 94 mm3axis magnitometer, the printed circuit board in 3D

    3axis magnitometer

    NarodniySputnik/Gladiolus-1

    Gladiolus-1 - автономный модуль для приема и передачи изображений в формате SSTV (Slow Scan TeleVision) на малом космическом аппарате (МКА) формата CubeSat

    96 parts9GPL-3.0
  • 8 layers22.3 × 77.5 mmTinker mantis, the printed circuit board in 3D

    Tinker mantis

    Tinkerbug-Robotics/TinkerRocket

    Model rocket flight computer, ground station, iOS app, and simulation

    279 parts1GPL-3.0
  • 2 layers50 × 50 mmBoreas, the printed circuit board in 3D

    Boreas

    darshg321/Boreas

    an STM32F7 flight controller for a rocket.

    100 parts
  • 4 layers37 × 37 mmNSSFC, the printed circuit board in 3D

    NSSFC

    Keyaan-07/NSSFC

    NSSFC is an FPV flight controller made with the STM32F405 and it has an IMU, Barometric pressure sensor and a magnetometer. It uses the betaflight as firmware(thus no firmware directory in this repository).

    97 parts
  • 4 layers59.5 × 117 mmTaz Main PCB V1.14, the printed circuit board in 3D

    Taz Main PCB V1.14

    root-applied-sciences/Taz-Main-PCB-V1.14

    113 parts
  • 2 layers9 × 57.6 mmTracker, the printed circuit board in 3D

    Tracker

    RunTheBot/Tracker

    44 parts
  • 2 layers68.7 × 64.9 mmSpindlyVR, the printed circuit board in 3D

    SpindlyVR

    SpindlySpider/spindlyVR

    65 partsGPL-3.0
  • 2 layers45 × 48 mmAetherpose custom, the printed circuit board in 3D

    Aetherpose custom

    thousandflame1000/aetherpose

    2026-10-18。已選方向:沿用 Arduino Nano 33 BLE 原版 ABX00030/帶針 ABX00034(LSM9DS1),製作供電與固定底板;六個穿戴位置各用一套。

    44 parts

Parts like it

1

Questions

Is there a KiCad symbol and footprint for the QMC5883P?

Yes. The symbol is EasyEDA_Cloud:QMC5883P and the footprint EasyEDA_Cloud:LGA-16_L3.0-W3.0-P0.50-BL_SQ, both drawn on this page. PCBKit places them on a board for you when you design with it.

What package is the QMC5883P?

LGA-16(3x3), with 16 pins. Its footprint is drawn on this page.

Where is the QMC5883P datasheet?

QST publishes it: the Datasheet link on this page opens it.

Where can I order the QMC5883P?

JLCPCB lists it as part C2847467, with 4,017 in stock; the sellers' links on this page open their listings.

What can replace the QMC5883P?

Parts like it in the library: the QMC5883L by QST. Check their datasheets: a part that fits the footprint may still differ in its ratings.

Which open-source boards use the QMC5883P?

11 boards in 9 repositories on GitHub; the most starred are listed on this page, with their KiCad files.