Skip to the content
12345678

PCA9306DC1

NXP SemiconductorsExtended

-40℃~+105℃ 1.8V~5.5V 1V~3.6V 2 2 2Mbps Automatic direction detection、Output enable high-impedance Bidirectional Level translator Open-drain SMBus、I2C VSSOP-8-0.5mm Translators, Level Shifters ROHS

Part id
nxp/PCA9306DC1
Category
Translators, Level Shifters
Package
VSSOP-8-0.5mm
Pins
8
In stock
2,796 at JLCPCB (C129510)
Used on
10 open-source boards

Overview

The PCA9306DC1 is a translators, Level Shifter made by NXP Semiconductors in a VSSOP-8-0.5mm package with 8 pins. -40℃~+105℃ 1.8V~5.5V 1V~3.6V 2 2 2Mbps Automatic direction detection、Output enable high-impedance Bidirectional Level translator Open-drain SMBus、I2C VSSOP-8-0.5mm Translators, Level Shifters ROHS.

PCBKit's library has its KiCad symbol (Interface:PCA9306DC1, from KiCad's library) and its footprint (Package_SO:VSSOP-8_3x3mm_P0.65mm, from KiCad's library), ready for a KiCad board. 2,796 are in stock at JLCPCB (part C129510). 10 open-source boards in 10 repositories on GitHub use it.

Symbol

1GND2VREF13SCL14SDA15SDA26SCL27VREF28EN
Interface:PCA9306DC1From KiCad's library

Footprint

12345678
Package_SO:VSSOP-8_3x3mm_P0.65mmFrom KiCad's library

From the datasheet

5
Supply, most
5 V · VREF1, recommended operating max · p. 6
Supply, absolute maximum
6 V · VREF1, absolute max · p. 6
Works from
-40 °C · operating free-air ambient min · p. 6
Works up to
105 °C · operating free-air ambient max · p. 6
Takes working
5 µA · reference transistor current, application typical · p. 10

What it is and has

6
Direction control
Bidirectional voltage translation with no direction pin · p. 2
ON-state connection resistance
3.5 Ω headline · p. 2
Disable behavior
High-impedance SCL1, SDA1, SCL2 and SDA2 when EN is LOW · p. 2
Lock-up
Lock-up free operation · p. 2
ESD protection
Exceeds 2000 V HBM per JESD22-A114 and 1000 V CDM per JESD22-C101 · p. 2
Package options
SO8, TSSOP8, VSSOP8, XQFN8, XSON8, X2SON8 · p. 2

Around it

2
res 200 kΩ
between VREF2/EN and Vpu(D); Typical pull-up for bidirectional translation; connect EN to VREF2. · p. 9
cap not specified
between VREF2 and GND; Recommended filter capacitor on VREF2; capacitance is not specified. · p. 9

Specifications

43
ParameterConditionsAs printedPage
reference voltage (1) Vref(1)Over operating free-air temperature rangemin -0.5 · max 6 V6
reference bias voltage (2) Vbias(ref)(2)Over operating free-air temperature rangemin -0.5 · max 6 V6
input voltage VIOver operating free-air temperature range; negative voltage rating may be exceeded if clamp current ratings are observedmin -0.5 · max 6 V6
voltage on an input/output pin VI/OOver operating free-air temperature range; negative voltage rating may be exceeded if clamp current ratings are observedmin -0.5 · max 6 V6
channel current (DC) IchOver operating free-air temperature rangemax 128 mA6
input clamping current IIKVI < 0 V; over operating free-air temperature rangemax -50 mA6
storage temperature Tstgmin -65 · max 150 °C6
voltage on an input/output pin VI/OSCL1, SDA1, SCL2, SDA2min 0 · max 5 V6
reference voltage (1) Vref(1)VREF1; Vref(1) ≤ Vbias(ref)(2) - 1 V for best results in level shifting applicationsmin 0 · max 5 V6
reference bias voltage (2) Vbias(ref)(2)VREF2; Vref(1) ≤ Vbias(ref)(2) - 1 V for best results in level shifting applicationsmin 0 · max 5 V6
input voltage on pin EN VI(EN)min 0 · max 5 V6
pass switch current Isw(pass)max 64 mA6
ambient temperature Tamboperating in free-airmin -40 · max 105 °C6
input clamping voltage VIKII = -18 mA; VI(EN) = 0 V; Tamb = -40 °C to +105 °Cmax -1.2 V6
HIGH-level input current IIHVI = 5 V; VI(EN) = 0 V; Tamb = -40 °C to +105 °Cmax 5 uA6
input capacitance on pin EN Ci(EN)VI = 3 V or 0 V; typical at Tamb = 25 °Ctyp 7.1 pF7
off-state input/output capacitance Cio(off)SCLn, SDAn; VO = 3 V or 0 V; VI(EN) = 0 V; Tamb = -40 °C to +105 °C; typical at 25 °Ctyp 4 · max 6 pF7
on-state input/output capacitance Cio(on)SCLn, SDAn; VO = 3 V or 0 V; VI(EN) = 3 V; Tamb = -40 °C to +105 °C; typical at 25 °Ctyp 9.3 · max 12.5 pF7
ON-state resistance RonSCLn, SDAn; VI = 0 V; IO = 64 mA; VI(EN) = 4.5 V; Tamb = -40 °C to +105 °C; typical at 25 °Ctyp 2.4 · max 5 Ω7
ON-state resistance RonSCLn, SDAn; VI = 0 V; IO = 64 mA; VI(EN) = 3 V; Tamb = -40 °C to +105 °C; typical at 25 °Ctyp 3 · max 6 Ω7
ON-state resistance RonSCLn, SDAn; VI = 0 V; IO = 64 mA; VI(EN) = 2.3 V; Tamb = -40 °C to +105 °C; typical at 25 °Ctyp 3.8 · max 8 Ω7
ON-state resistance RonDC1 (VSSOP8); SCLn, SDAn; VI = 0 V; IO = 64 mA; VI(EN) = 1.5 V; footnote [4]; Tamb = -40 °C to +105 °C; typical at 25 °Ctyp 32 · max 80 Ω7
ON-state resistance RonSCLn, SDAn; VI = 2.4 V; IO = 15 mA; VI(EN) = 4.5 V; Tamb = -40 °C to +105 °C; typical at 25 °Ctyp 4.8 · max 7.5 Ω7
ON-state resistance RonSCLn, SDAn; VI = 2.4 V; IO = 15 mA; VI(EN) = 3 V; Tamb = -40 °C to +105 °C; typical at 25 °Ctyp 46 · max 80 Ω7
ON-state resistance RonSCLn, SDAn; VI = 1.7 V; IO = 15 mA; VI(EN) = 2.3 V; Tamb = -40 °C to +105 °C; typical at 25 °Ctyp 40 · max 80 Ω7
LOW to HIGH propagation delay tPLHCL = 50 pF; VI(EN) = 3.3 V; VIH = 3.3 V; VIL = 0 V; VM = 1.15 V; SCL2 or SDA2 to SCL1 or SDA1; Tamb = -40 °C to +105 °Cmin 0 · max 2 ns7
LOW to HIGH propagation delay tPLHCL = 30 pF; VI(EN) = 3.3 V; VIH = 3.3 V; VIL = 0 V; VM = 1.15 V; SCL2 or SDA2 to SCL1 or SDA1; Tamb = -40 °C to +105 °Cmin 0 · max 1.2 ns7
LOW to HIGH propagation delay tPLHCL = 15 pF; VI(EN) = 3.3 V; VIH = 3.3 V; VIL = 0 V; VM = 1.15 V; SCL2 or SDA2 to SCL1 or SDA1; Tamb = -40 °C to +105 °Cmin 0 · max 0.6 ns7
HIGH to LOW propagation delay tPHLCL = 50 pF; VI(EN) = 3.3 V; VIH = 3.3 V; VIL = 0 V; VM = 1.15 V; SCL2 or SDA2 to SCL1 or SDA1; Tamb = -40 °C to +105 °Cmin 0 · max 2 ns7
HIGH to LOW propagation delay tPHLCL = 30 pF; VI(EN) = 3.3 V; VIH = 3.3 V; VIL = 0 V; VM = 1.15 V; SCL2 or SDA2 to SCL1 or SDA1; Tamb = -40 °C to +105 °Cmin 0 · max 1.5 ns7
HIGH to LOW propagation delay tPHLCL = 15 pF; VI(EN) = 3.3 V; VIH = 3.3 V; VIL = 0 V; VM = 1.15 V; SCL2 or SDA2 to SCL1 or SDA1; Tamb = -40 °C to +105 °Cmin 0 · max 0.75 ns7
LOW to HIGH propagation delay tPLHCL = 50 pF; VI(EN) = 2.5 V; VIH = 2.5 V; VIL = 0 V; VM = 0.75 V; SCL2 or SDA2 to SCL1 or SDA1; Tamb = -40 °C to +105 °Cmin 0 · max 2 ns7
LOW to HIGH propagation delay tPLHCL = 30 pF; VI(EN) = 2.5 V; VIH = 2.5 V; VIL = 0 V; VM = 0.75 V; SCL2 or SDA2 to SCL1 or SDA1; Tamb = -40 °C to +105 °Cmin 0 · max 1.2 ns7
LOW to HIGH propagation delay tPLHCL = 15 pF; VI(EN) = 2.5 V; VIH = 2.5 V; VIL = 0 V; VM = 0.75 V; SCL2 or SDA2 to SCL1 or SDA1; Tamb = -40 °C to +105 °Cmin 0 · max 0.6 ns7
HIGH to LOW propagation delay tPHLCL = 50 pF; VI(EN) = 2.5 V; VIH = 2.5 V; VIL = 0 V; VM = 0.75 V; SCL2 or SDA2 to SCL1 or SDA1; Tamb = -40 °C to +105 °Cmin 0 · max 2.5 ns7
HIGH to LOW propagation delay tPHLCL = 30 pF; VI(EN) = 2.5 V; VIH = 2.5 V; VIL = 0 V; VM = 0.75 V; SCL2 or SDA2 to SCL1 or SDA1; Tamb = -40 °C to +105 °Cmin 0 · max 1.5 ns7
HIGH to LOW propagation delay tPHLCL = 15 pF; VI(EN) = 2.5 V; VIH = 2.5 V; VIL = 0 V; VM = 0.75 V; SCL2 or SDA2 to SCL1 or SDA1; Tamb = -40 °C to +105 °Cmin 0 · max 0.75 ns7
reference bias voltage (2) Vbias(ref)(2)Refer to Figure 9; minimum = Vref(1) + 0.6 V; typical at Tamb = 25 °Ctyp 2.1 · max 5 V10
input voltage on pin EN VI(EN)Refer to Figure 9; minimum = Vref(1) + 0.6 V; typical at Tamb = 25 °Ctyp 2.1 · max 5 V10
reference voltage (1) Vref(1)Refer to Figure 9; typical at Tamb = 25 °Cmin 0 · typ 1.5 · max 4.4 V10
pass switch current Isw(pass)Refer to Figure 9; typical at Tamb = 25 °Ctyp 14 mA10
reference current Ireftransistor; refer to Figure 9; typical at Tamb = 25 °Ctyp 5 uA10
ambient temperature Tamboperating in free-air; refer to Figure 9min -40 · max 105 °C10

Pins, by the datasheet

8
1 GND
Ground (0 V). · p. 5
2 VREF1
Low-voltage side reference supply voltage for SCL1 and SDA1. · p. 5
3 SCL1
Serial clock, low-voltage side; connect to VREF1 through a pull-up resistor. · p. 5
4 SDA1
Serial data, low-voltage side; connect to VREF1 through a pull-up resistor. · p. 5
5 SDA2
Serial data, high-voltage side; connect to VREF2 through a pull-up resistor. · p. 5
6 SCL2
Serial clock, high-voltage side; connect to VREF2 through a pull-up resistor. · p. 5
7 VREF2
High-voltage side reference supply voltage for SCL2 and SDA2. · p. 5
8 EN
Switch enable input; connect to VREF2 and pull up through a high resistor. · p. 5

Ordering codes, by the datasheet

9
PCA9306D,118
SO8 · Reel 13” Q1/T1, standard mark SMD; minimum order 2500; Tamb = -40 °C to +105 °C · p. 3
PCA9306DC1,125
VSSOP8 · Reel 7” Q3/T4, standard mark; minimum order 3000; Tamb = -40 °C to +105 °C; discontinuation notice directs customers to PCA9306DC1Z · p. 3
PCA9306DC1Z
VSSOP8 · Reel 7” Q3/T4, standard mark SSB; minimum order 3000; Tamb = -40 °C to +105 °C · p. 3
PCA9306DC1/DG,125
VSSOP8 · Dark green package material; reel 7” Q3/T4, standard mark; minimum order 3000; Tamb = -40 °C to +105 °C · p. 3
PCA9306DP,118
TSSOP8 · SOT505-1, body width 3 mm; reel 13” Q1/T1, standard mark SMD; minimum order 2500; Tamb = -40 °C to +105 °C · p. 3
PCA9306DP1,125
TSSOP8 · SOT505-2, body width 3 mm, lead length 0.5 mm; reel 7” Q3/T4, standard mark; minimum order 3000; Tamb = -40 °C to +105 °C · p. 3
PCA9306GF,115
XSON8 · Body 1.35 x 1 x 0.5 mm; reel 7” Q1/T1, standard mark SMD; minimum order 5000; Tamb = -40 °C to +105 °C; being replaced by PCA9306JK · p. 3
PCA9306JKZ
X2SON8 · Body 1.35 x 1 x 0.32 mm; reel 7” Q1/T1; minimum order 6000; Tamb = -40 °C to +105 °C · p. 3
PCA9306GM,125
XQFN8 · Reel 7” Q3/T4, standard mark; minimum order 4000; Tamb = -40 °C to +105 °C · p. 4

Open-source boards using it

10See all 10
  • 4 layers65 × 30 mmIcepi zero, the printed circuit board in 3D

    Icepi zero

    cheyao/icepi-zero

    An ECP5 FPGA Dev Board in a Pi Zero form

    163 parts869
  • 2 layers61.3 × 45.2 mmHashHacker Hashboard Tester, the printed circuit board in 3D

    HashHacker Hashboard Tester

    DCentralTech/HashHacker-Multi-Hashboard-Tester

    HashHacker Multi-Hashboard Tester from D-Central, the ultimate open-source tool for repairing and testing your ASIC miners.

    30 parts9GPL-3.0
  • 4 layers51.3 × 21 mmWifi interposer, the printed circuit board in 3D

    Wifi interposer

    dsi-modchip/pcb

    This repository contains the KiCAD design files for the DSi modchip and the cable flex-PCB.

    89 parts2CERN-OHL-S-2.0
  • 4 layers100 × 67.8 mmAlarmbot, the printed circuit board in 3D

    Alarmbot

    benthacher/alarmbot

    Alarmbot pcb and firmware (and rpi cm5 software)

    227 parts
  • 2 layers30 × 62 mmWiFIR, the printed circuit board in 3D

    WiFIR

    Duckle29/WiFIR

    A WiFi connected IR blaster to control heatpumps

    34 partsBSD-3-Clause
  • 2 layers40.9 × 84.4 mmBicycle board, the printed circuit board in 3D

    Bicycle board

    XuHg-zjcn/bicycle_board

    a PCB board for bicycle

    158 partsCERN-OHL-S-2.0
  • 4 layers65 × 30 mmIcepi zero, the printed circuit board in 3D

    Icepi zero

    hackclub/OnBoard

    💡 Join 1,000 teenagers and make your first PCB with a $100 grant!

    122 parts915
  • 2 layers84.5 × 54.6 mmMain board v2, the printed circuit board in 3D

    Main board v2

    felixzero/escrocs

    Repository for the ESCROCS team for the french robotics cup 2020!

    75 parts7GPL-3.0

Parts like it

8

Questions

Is there a KiCad symbol and footprint for the PCA9306DC1?

Yes. The symbol is Interface:PCA9306DC1 and the footprint Package_SO:VSSOP-8_3x3mm_P0.65mm, both drawn on this page. PCBKit places them on a board for you when you design with it.

What package is the PCA9306DC1?

VSSOP-8-0.5mm, with 8 pins. Its footprint is drawn on this page.

Where is the PCA9306DC1 datasheet?

NXP Semiconductors publishes it: the Datasheet link on this page opens it.

Where can I order the PCA9306DC1?

JLCPCB lists it as part C129510, with 2,796 in stock; the sellers' links on this page open their listings.

What can replace the PCA9306DC1?

Parts like it in the library: the 74LVC2T45DC by Nexperia, the TCA9517ADGKR by Texas Instruments, the RS0102YVS8 by Jiangsu RUNIC Tech and the LSF0102DCH by Nexperia. Check their datasheets: a part that fits the footprint may still differ in its ratings.

Which open-source boards use the PCA9306DC1?

10 boards in 10 repositories on GitHub; the most starred are listed on this page, with their KiCad files.