
NPM1100-QDAA-R
Nordic SemiconExtended
-40℃~+85℃ 1 4.1V~6.7V Lithium-ion/Polymer QFN-24(4x4) Power Management - Specialized ROHS
- Part id
- nordic-semicon/NPM1100-QDAA-R
- Category
- Battery Management
- Package
- QFN-24(4x4)
- Pins
- 25
- In stock
- 1,576 at JLCPCB (C5816773)
- Used on
- 7 open-source boards
Overview
The NPM1100-QDAA-R is a battery Management made by Nordic Semicon in a QFN-24(4x4) package with 25 pins. -40℃~+85℃ 1 4.1V~6.7V Lithium-ion/Polymer QFN-24(4x4) Power Management - Specialized ROHS.
1,576 are in stock at JLCPCB (part C5816773). 7 open-source boards in 6 repositories on GitHub use it.
Symbol
The library has no symbol for this part yet.
Footprint
The library has no footprint for this part yet.
From the datasheet
19- Supply, least
- 4.1 V · VBUS, recommended operating min · p. 14
- Supply, most
- 6.7 V · VBUS, recommended operating max · p. 14
- Supply, least
- 2.3 V · VBAT, recommended operating min · p. 14
- Supply, most
- 4.35 V · VBAT, recommended operating max · p. 14
- Supply, absolute maximum
- 20 V · VBUS, absolute max · p. 13
- Supply, absolute maximum
- 5.5 V · VBAT, absolute max · p. 13
- Works from
- -40 °C · Ambient operating min · p. 14
- Works up to
- 85 °C · Ambient operating max · p. 14
- Junction, hottest
- 125 °C · Junction temperature max · p. 14
- Takes working
- 800 nA · VBAT, typical quiescent current, no load, MODE LOW, VBUS disconnected · p. 12
- Takes asleep
- 460 nA · VBAT, typical Ship mode quiescent current · p. 12
- Gives
- 150 mA · BUCK rated output max · p. 3
- Gives
- 400 mA · Battery charger rated charge current max · p. 3
- Current limit
- 660 mA · Battery discharge output current limit typical · p. 25
- Dropout
- 410 mV · BUCK dropout typical; load unspecified · p. 30
- Switches at
- 3.6 MHz · BUCK PWM switching frequency typical · p. 30
- Junction to air (WLCSP 25 pins)
- 50.7 K/W · Junction-to-ambient thermal resistance · p. 14
- Junction to case (WLCSP 25 pins)
- 9.2 K/W · Junction-to-case top thermal resistance · p. 14
- Junction to board (WLCSP 25 pins)
- 22.6 K/W · Junction-to-board thermal resistance · p. 14
What it is and has
16- Battery charger
- 400 mA linear lithium-ion/lithium-polymer charger · p. 3
- Charge current
- Adjustable from 20 mA to 400 mA · p. 3
- Charge termination voltage
- Selectable 4.1 V or 4.2 V · p. 3
- Buck regulator
- 1.8 V to 3.0 V, 150 mA · p. 3
- Buck output selection
- 1.8 V, 2.1 V, 2.7 V, 3.0 V; pin selectable · p. 3
- Charging indication driver
- 5 mA low side LED driver · p. 3
- Error indication driver
- 5 mA low side LED driver · p. 3
- Thermal protection
- Battery thermal protection · p. 3
- Protection
- Thermal protection · p. 3
- Protection
- Discharge current limitation · p. 3
- Protection
- Reverse current protection · p. 3
- USB input current limits
- 100 mA and 500 mA · p. 3
- USB port detection
- SDP, DCP, CDP; Battery Charging Specification v1.2 · p. 15
- Battery thermal charging profile
- JEITA compliant; standard and extended temperature range · p. 19
- Package
- 2.1x2.1 mm WLCSP · p. 3
- Software control
- No software control · p. 2
Around it
7- res 0 Ω
- between ICHG and AVSS; Short to AVSS selects nominal 400 mA charge current. · p. 21
- res 1.5 kΩ
- between ICHG and AVSS; Selects nominal 200 mA charge current. · p. 21
- res 4.7 kΩ
- between ICHG and AVSS; Selects nominal 100 mA charge current. · p. 21
- res 11 kΩ
- between ICHG and AVSS; Selects nominal 50 mA charge current. · p. 21
- res 30 kΩ
- between ICHG and AVSS; Selects nominal 20 mA charge current. · p. 21
- other 10 kΩ NTC thermistor
- between NTC and AVSS; Nominal resistance at 25°C; thermal contact with battery, preferably within battery pack; resistance accuracy 1%, B25/50 = 3380 Kelvin. · p. 22
- res 10 kΩ
- between NTC and AVSS; ≤20% accuracy; use when battery thermal protection is not used. · p. 22
Specifications
88| Parameter | Conditions | As printed | Page |
|---|---|---|---|
| Ship mode quiescent current IQSHIP | typ 460 nA | 12 | |
| Quiescent current, battery operation, no load, MODE = LOW, VBUS disconnected IQBAT | Battery operation, no load, MODE = LOW, VBUS disconnected | typ 800 nA | 12 |
| Thermal shutdown threshold TSD | typ 120 °C | 12 | |
| Thermal shutdown hysteresis TSDHYST | typ 10 °C | 12 | |
| Input HIGH VIH | Maximum = VINT | min 1.1 V | 12 |
| Input LOW VIL | min 0 · max 0.4 V | 12 | |
| Internal resistance between SHPACT and AVSS RSHPACT | typ 500 kΩ | 12 | |
| Duration SHPACT must be held high to enable Ship mode tactiveToShip | min 200 ms | 12 | |
| Duration SHPHLD must be held low to disable Ship mode tshipToActive | min 200 ms | 12 | |
| VBUS VBUS | Power; absolute maximum ratings | min -0.3 · max 20 V | 13 |
| VBAT VBAT | Power; absolute maximum ratings | min -0.3 · max 5.5 V | 13 |
| VSYS, DEC, SW | Absolute maximum ratings | min -0.3 · max 5.5 V | 13 |
| AVSS, PVSS | Power; absolute maximum ratings | max 0 V | 13 |
| Analog I/O VANAI/O | D-, D+, NTC, ICHG, VOUTB; maximum = VINT + 0.3 V | min -0.3 V | 13 |
| Digital I/O VDIGI/O | VOUTBSET0, VOUTBSET1, VTERMSET, SHPHLD, SHPACT, ISET, ERR, CHG, MODE; maximum = VINT + 0.3 V | min -0.3 V | 13 |
| Storage temperature | WLCSP package | min -40 · max 125 °C | 13 |
| Moisture Sensitivity Level MSL | WLCSP package | max 1 | 13 |
| Human Body Model Class 2 ESD HBM | WLCSP package | max 2 kV | 13 |
| Charged Device Model ESD CDM | WLCSP package | max 500 V | 13 |
| Supply voltage VBUSOP | Nom. = 5 V | min 4.1 · typ 5 · max 6.7 V | 14 |
| Battery voltage VBATOP | min 2.3 · max 4.35 V | 14 | |
| Junction temperature TJ | min -40 · max 125 °C | 14 | |
| Operating temperature TO | Ambient | min -40 · max 85 °C | 14 |
| Junction-to-ambient thermal resistance RϴJA | WLCSP 25 pins; JESD51-7; single stated value | typ 50.7 °C/W | 14 |
| Junction-to-case (top) thermal resistance RϴJC(top) | WLCSP 25 pins; JESD51-7; single stated value | typ 9.2 °C/W | 14 |
| Junction-to-board thermal resistance RϴJB | WLCSP 25 pins; JESD51-7; single stated value | typ 22.6 °C/W | 14 |
| Junction-to-top characterization parameter ΨJT | WLCSP 25 pins; JESD51-7; single stated value | typ 1.05 °C/W | 14 |
| Junction-to-board characterization parameter ΨJB | WLCSP 25 pins; JESD51-7; single stated value | typ 23 °C/W | 14 |
| Max VBUS input current, CDP/DCP USB or ISET = HIGH IBUSLIM1 | CDP/DCP USB or ISET = HIGH | min 450 · max 500 mA | 16 |
| Max VBUS input current, SDP USB and ISET = LOW, 25°C IBUSLIM0 | SDP USB and ISET = LOW, 25°C | min 90 · max 100 mA | 17 |
| Regulated VINT voltage from SYSREG, VBUS = 6 V VINTREG | VBUS = 6 V | typ 5.2 V | 17 |
| SYSREG on resistance, ISET = HIGH RONREG | ISET = HIGH | typ 440 · max 720 mΩ | 17 |
| Overvoltage protection threshold VBUSOVP | typ 6.9 V | 17 | |
| Undervoltage threshold VBUSMIN | typ 3.9 V | 17 | |
| Threshold for entering ULP mode VBUSULP | typ 1.8 V | 17 | |
| Power-on reset release voltage for VBUS VBUSPOR | typ 3.9 V | 17 | |
| Brownout reset trigger voltage for VBUS VBUSBOR | BOR requires both V(VBUS) < VBUSBOR and V(VBAT) < VBATBOR | typ 3.8 V | 17 |
| Time for USB detection, ISET = LOW TCONN0 | ISET = LOW | max 700 ms | 17 |
| Time for VINT to settle after VBUS connection, ISET = HIGH, no load TCONN1 | ISET = HIGH, no load | typ 1.2 ms | 17 |
| Time for system to reach ULP mode after VBUS disconnect, CVBUS = 10 uF TDISCONN | VBUS disconnect, CVBUS = 10 uF | typ 110 ms | 17 |
| Nominal resistance at 25°C | Single stated value | typ 10 kΩ | 22 |
| Resistance accuracy | Stated accuracy | typ 1 % | 22 |
| B25/50 constant | Single stated value | typ 3380 Kelvin | 22 |
| B25/85 constant | Stated range | min 3434 · max 3435 Kelvin | 22 |
| B constant accuracy | Stated accuracy | typ 1 % | 22 |
| Trickle charging timeout TOUTTRICKLE | typ 10 min | 25 | |
| Timeout for Fast charging and constant current charging TOUTCHARGE | typ 7 hour | 25 | |
| VINT - VBAT voltage for charging VDROPOUT_CHARGER | typ 50 mV | 25 | |
| Minimum VBUS - VBAT voltage for charging VDROPOUT_VBUS | typ 140 mV | 25 | |
| Period between detection events TREDETECT | typ 500 ms | 25 | |
| Output current limit from battery in discharge IBATLIM | Battery discharge | typ 660 mA | 25 |
| CHARGER resistance between VBAT and VINT in Discharge, VBAT = 3.7 V RONCHARGER | Discharge, VBAT = 3.7 V | typ 130 · max 230 mΩ | 25 |
| Power-on reset release voltage for VBAT VBATPOR | typ 2.7 V | 25 | |
| Brownout reset trigger voltage for VBAT VBATBOR | BOR requires both V(VBUS) < VBUSBOR and V(VBAT) < VBATBOR | typ 2.5 V | 25 |
| DC current (CHG and ERR) ISINK | CHG and ERR | typ 5 mA | 25 |
| JEITA cold temperature threshold (Thermistor: 10 kΩ, B25/50=3380 K) TNTCCOLD | Thermistor: 10 kΩ, B25/50=3380 K | typ 0 °C | 25 |
| Resistance threshold from cool to cold RNTCCOLD_FALLING | min 25.53 · typ 27.28 · max 29.13 kΩ | 25 | |
| Resistance threshold from cold to cool RNTCCOLD_RISING | min 23.1 · typ 26 · max 28.2 kΩ | 25 | |
| JEITA cool temperature threshold (Thermistor: 10 kΩ, B25/50=3380 K) TNTCCOOL | Thermistor: 10 kΩ, B25/50=3380 K | typ 10 °C | 25 |
| Resistance threshold from nom. to cool RNTCCOOL_FALLING | min 16.8 · typ 18 · max 19.2 kΩ | 25 | |
| Resistance threshold from cool to nom. RNTCCOOL_RISING | min 15.5 · typ 17.1 · max 18.6 kΩ | 25 | |
| JEITA warm temperature threshold (Thermistor: 10 kΩ, B25/50=3380 K) TNTCWARM | Thermistor: 10 kΩ, B25/50=3380 K | typ 45 °C | 25 |
| Resistance threshold from warm to nom. RNTCWARM_FALLING | min 4.86 · typ 5.13 · max 5.43 kΩ | 25 | |
| Resistance threshold from nom. to warm RNTCWARM_RISING | min 4.68 · typ 4.92 · max 5.17 kΩ | 25 | |
| JEITA hot temperature threshold (Thermistor: 10 kΩ, B25/50=3380 K) TNTCHOT | Thermistor: 10 kΩ, B25/50=3380 K | typ 60 °C | 25 |
| Resistance threshold from hot to warm RNTCHOT_FALLING | min 3.04 · typ 3.19 · max 3.35 kΩ | 25 | |
| Resistance threshold from warm to hot RNTCHOT_RISING | min 2.9 · typ 3.02 · max 3.15 kΩ | 25 | |
| Nominal inductance | Recommended inductor | typ 2.2 uH | 30 |
| Inductor tolerance | Recommended inductor | max 20 % | 30 |
| DC resistance (DCR) | Recommended inductor | max 400 mΩ | 30 |
| Saturation current (lsat) | Recommended inductor | min 350 mA | 30 |
| Maximum current (lmax) | Recommended inductor | min 350 mA | 30 |
| Recommended nominal capacitor | Effective capacitance at VOUTB: 6 uF minimum, 20 uF maximum | min 6 · typ 10 · max 20 uF | 30 |
| VOUTB accuracy under static conditions; no change in supply voltage, load current, or Buck operating mode VOUTBACC | Static conditions; no change in supply voltage, load current, or Buck operating mode | min -2 · max 8 % | 30 |
| Short circuit current limit IOUTBSHORT | max 400 mA | 30 | |
| Load current threshold from Hysteretic to PWM mode (MODE = LOW) IPWMTHRES | MODE = LOW | typ 90 mA | 30 |
| Load current threshold from PWM to Hysteretic mode (MODE = LOW) IHYSTTHRES | MODE = LOW | typ 40 mA | 30 |
| VOUTB ripple, MODE = HIGH or load current above IPWMTHRES VOUTBRIPPLE_HYST | MODE = HIGH or load current above IPWMTHRES | max 10 mVpp | 30 |
| VOUT ripple, MODE = LOW and load current below IPWMTHRES VOUTBRIPPLE_HYST | MODE = LOW and load current below IPWMTHRES | max 80 mVpp | 30 |
| Efficiency, VOUTBSET = 11 (VOUTB = 3.0 V), VINT = 3.7 V, IOUTB = 100 mA EFFBUCK | VOUTBSET = 11 (VOUTB = 3.0 V), VINT = 3.7 V, IOUTB = 100 mA | typ 93.5 % | 30 |
| Dropout voltage, V(VOUTB) - VINT VDROPOUT_BUCK | typ 0.41 V | 30 | |
| Switching frequency for PWM mode FBUCK | PWM mode | typ 3.6 MHz | 30 |
| Hysteretic to PWM mode transition time on MODE pin toggle TPWMMODE | MODE pin toggle | max 55 us | 30 |
| PWM to Hysteretic mode transition time on MODE pin toggle THYSTMODE | MODE pin toggle | max 25 us | 30 |
| Hysteretic to PWM mode transition time TPWM | max 90 us | 30 | |
| PWM to Hysteretic mode transition time THYST | max 35 us | 31 | |
| Settling time to within 1% after load transient of 0 A to 100 mA TSETTLE | Load transient of 0 A to 100 mA | max 20 us | 31 |
| Minimum VINT voltage for enabling BUCK VINTBUCKMIN | typ 2.8 V | 31 |
Open-source boards using it
7- 4 layers50 × 50 mm

- 6 layers38 × 39 mm

- 4 layers66 × 42 mm

- 4 layers

NRF development board HAN V1.0
EmielV2002/nRF_dev_board
A dev board utilizing the nRF53 and nPM1100 chip.
105 partsGPL-3.0 - 4 layers59.4 × 30 mm

- 4 layers93 × 94.8 mm

- 4 layers20.8 × 29 mm

Questions
What package is the NPM1100-QDAA-R?
QFN-24(4x4), with 25 pins.
Where is the NPM1100-QDAA-R datasheet?
Nordic Semicon publishes it: the Datasheet link on this page opens it.
Where can I order the NPM1100-QDAA-R?
JLCPCB lists it as part C5816773, with 1,576 in stock; the sellers' links on this page open their listings.
Which open-source boards use the NPM1100-QDAA-R?
7 boards in 6 repositories on GitHub; the most starred are listed on this page, with their KiCad files.