Skip to the content
12345678

ATA6563-GAQW1

Microchip TechnologyExtended

-40℃~+125℃ 12uA 4.5V~5.5V 5Mbps 70mA CAN Transceiver SOIC-8 CAN Transceivers ROHS

Part id
microchip/ATA6563-GAQW1
Category
CAN Transceivers
Package
SOIC-8
Pins
8
In stock
4,065 at JLCPCB (C5127614)
Used on
5 open-source boards

Overview

The ATA6563-GAQW1 is a CAN Transceiver made by Microchip Technology in a SOIC-8 package with 8 pins. -40℃~+125℃ 12uA 4.5V~5.5V 5Mbps 70mA CAN Transceiver SOIC-8 CAN Transceivers ROHS.

PCBKit's library has its KiCad symbol (EasyEDA_Cloud:ATA6563-GAQW1, from EasyEDA) and its footprint (Package_SO:SOIC-8_3.9x4.9mm_P1.27mm, from KiCad's library), ready for a KiCad board. 4,065 are in stock at JLCPCB (part C5127614). 5 open-source boards in 5 repositories on GitHub use it.

Symbol

1TXD2GND3VCC4RXD5VIO6CANL7CANH8STBY
EasyEDA_Cloud:ATA6563-GAQW1From EasyEDA

Footprint

12345678
Package_SO:SOIC-8_3.9x4.9mm_P1.27mmFrom KiCad's library

From the datasheet

11
Supply, least
4.5 V · VCC, recommended operating min · p. 11
Supply, most
5.5 V · VCC, recommended operating max · p. 11
Supply, least
2.8 V · VIO, recommended operating min · p. 11
Supply, absolute maximum
5.5 V · VCC, absolute max · p. 11
Works from
-40 °C · Grade 1 ambient min · p. 11
Works up to
125 °C · Grade 1 ambient max · p. 11
Junction, hottest
175 °C · Virtual junction temperature absolute max · p. 11
Takes at most
70.5 mA · sum of VCC and VIO max normal dominant currents, VTXD = 0 V · p. 11
Takes asleep
13 µA · sum of VCC and VIO max standby currents · p. 11
Junction to air (SOIC8)
145 K/W · Virtual junction to ambient typical · p. 15
Data rate, most
5 Mbit/s · Communication speed max · p. 1

What it is and has

7
CAN FD
Ready · p. 1
Communication speed
Up to 5 Mbps · p. 1
Functional safety
ISO 26262 Functional Safety Ready · p. 1
Qualification
AEC-Q100 and AEC-Q006 · p. 1
Protection
CANH/CANL short-circuit and overtemperature protection · p. 1
Undervoltage detection
VCC and VIO · p. 1
RXD recessive clamping detection
Supported · p. 1

Around it

2
cap 100 nF
between VIO and GND; Shown in the ATA6563 typical application. · p. 10
cap 22 µF
between VCC and GND; Shown in the ATA6563 typical application; size depends on the external voltage regulator. · p. 10

Specifications

93
ParameterConditionsAs printedPage
DC Voltage at CANH, CANL VCANH, VCANLmin -27 · max 42 V11
Transient Voltage at CANH, CANL VCANH, VCANLaccording to ISO 7637 part 2min -150 · max 100 V11
Max. Differential Bus Voltage VDiffmin -5 · max 18 V11
DC Voltage on all other Pins VXmin -0.3 · max 5.5 V11
ESD according to IBEE CAN EMC - Test Specification Following IEC 61000-4-2 - Pin CANH, CANLPin CANH, CANLmin -8 · max 8 kV11
ESD (HBM Following STM5.1 with 1.5 kΩ/100 pF) - Pins CANH, CANL to GNDPins CANH, CANL to GNDmin -6 · max 6 kV11
Component Level ESD (HBM according to ANSI/ESD STM5.1, JESD22-A114, AEC-Q100 (002)min -4 · max 4 kV11
CDM ESD STM 5.3.1min -750 · max 750 V11
ESD Machine Model AEC-Q100-RevF(003)min -200 · max 200 V11
Virtual Junction Temperature TvJmin -40 · max 175 °C11
Storage Temperature Range Tstgmin -55 · max 150 °C11
Supply Voltage VVCCSupply, Pin VCC; Grade 1min 4.5 · max 5.5 V11
Supply Current in Normal Mode IVCC_recRecessive, VTXD = VVIOmin 2 · max 5 mA11
Supply Current in Normal Mode IVCC_domDominant, VTXD = 0Vmin 30 · typ 50 · max 70 mA11
Supply Current in Normal Mode IVCC_shortShort between CANH and CANL (Note 1)max 85 mA11
Supply Current in Standby Mode IVCC_STBYVCC = VIO, VTXD = VNSIL = VVIOmax 12 uA11
Supply Current in Standby Mode IVCC_STBYTa = 25°C (Note 3)typ 7 uA11
Undervoltage Detection Threshold on Pin VCC Vuvd(VCC)min 2.75 · max 4.5 V11
Supply Voltage on Pin VIO VVIOATA6563min 2.8 · max 5.5 V11
Supply Current on Pin VIO IVIO_recATA6563; Normal mode, Recessive, VTXD = VVIOmin 10 · typ 80 · max 250 uA11
Supply Current on Pin VIO IVIO_domATA6563; Normal mode, Dominant, VTXD = 0Vmin 50 · typ 350 · max 500 uA11
Supply Current on Pin VIO IVIO_STBYATA6563; Standby modemax 1 uA11
Undervoltage Detection Threshold on Pin VIO Vuvd(VIO)ATA6563min 1.3 · max 2.7 V11
Low-Level Input Voltage VILPin STBY; max = 0.3 × VVIOmin -0.3 V12
Pull-Up Resistor to VCC RpuPin STBY; VSTBY = 0V, VNSIL = 0Vmin 75 · typ 125 · max 175 kΩ12
High-Level Leakage Current ILPin STBY; VSTBY = VVIO, VNSIL = VVIOmin -2 · max 2 uA12
Low-Level Input Voltage VILPin TXD; max = 0.3 × VVIOmin -0.3 V12
Pull-Up Resistor to VCC RTXDPin TXD; VTXD = 0Vmin 20 · typ 35 · max 50 kΩ12
High-Level Leakage Current ITXDNormal mode, VTXD = VVIOmin -2 · max 2 uA12
Input Capacitance CTXDNote 3typ 5 · max 10 pF12
High-Level Output Current IOHPin RXD; Normal mode, VRXD = VVIO – 0.4V, VVIO = VVCCmin -8 · max -1 mA12
Low-Level Output Current, Bus Dominant IOLPin RXD; Normal mode, VRXD = 0.4V, Bus Dominantmin 2 · max 12 mA12
Single Ended Dominant Output Voltage VO(dom)VTXD = 0V, t < tto(dom)TXD; RL = 50Ω to 65Ω; pin CANH (Note 1)min 2.75 · typ 3.5 · max 4.5 V12
Single Ended Dominant Output Voltage VO(dom)VTXD = 0V, t < tto(dom)TXD; RL = 50Ω to 65Ω; pin CANL (Note 1)min 0.5 · typ 1.5 · max 2.25 V12
Transmitter Voltage Symmetry VSymVSym = (VCANH + VCANL) / VVCC; Split Termination, RL = 2 x 30Ω, CSplit = 4.7 nF (Note 3)min 0.9 · typ 1 · max 1.1 —12
Bus Differential Output Voltage VDiffVTXD = 0V, t < tto(dom)TXD; RL = 45Ω to 65Ωmin 1.5 · max 3 V12
Bus Differential Output Voltage VDiffVTXD = 0V, t < tto(dom)TXD; RL = 70Ω (Note 3)min 1.5 · max 3.3 V12
Bus Differential Output Voltage VDiffVTXD = 0V, t < tto(dom)TXD; RL = 2240Ω (Note 3)min 1.5 · max 5 V12
Bus Differential Output Voltage VDiffNormal mode; VVCC = 4.75V to 5.25V; VTXD = VVIO, recessive, no loadmin -50 · max 50 mV12
Bus Differential Output Voltage VDiffStandby mode; VVCC = 4.75V to 5.25V; VTXD = VVIO, recessive, no loadmin -200 · max 200 mV12
Single Ended Recessive Output Voltage VO(rec)Normal mode, VTXD = VVIO, no load; typ = 0.5 × VVCCmin 2 · max 3 V13
Single Ended Recessive Output Voltage VO(rec)Standby mode, VTXD = VVIO, no loadmin -0.1 · max 0.1 V13
Differential Receiver Threshold Voltage Vth(RX)difNormal mode (HSC), Vcm(CAN) = –27V to +27Vmin 0.5 · typ 0.7 · max 0.9 V13
Differential Receiver Threshold Voltage Vth(RX)difStandby mode (WUC), Vcm(CAN) = –27V to +27V (Note 1)min 0.4 · typ 0.7 · max 1.1 V13
Differential Receiver Hysteresis Voltage Vhys(RX)difNormal mode (HSC), Vcm(CAN) = –27V to +27V (Note 1)min 50 · typ 120 · max 200 mV13
Dominant Output Current IIO(dom)VTXD = 0V, t < tto(dom)TXD, VVCC = 5V; pin CANH, VCANH = –5Vmin -75 · max -35 mA13
Dominant Output Current IIO(dom)VTXD = 0V, t < tto(dom)TXD, VVCC = 5V; pin CANL, VCANL = +40Vmin 35 · max 75 mA13
Recessive Output Current IIO(rec)Normal mode, VTXD = VVIO, no load, VCANH = VCANL = –27V to +32Vmin -5 · max 5 mA13
Leakage Current IIO(leak)VVCC = VVIO = 0V, VCANH = VCANL = 5Vmin -5 · typ 0 · max 5 uA13
Leakage Current IIO(leak)VCC = VIO connected to GND with R = 47kΩ; VCANH = VCANL = 5V (Note 3)min -5 · typ 0 · max 5 uA13
Input Resistance RiVCANH = VCANL = 4Vmin 9 · typ 15 · max 28 kΩ13
Input Resistance Ri–2V ≤ VCANH ≤ +7V, –2V ≤ VCANL ≤ +7V (Note 3)min 9 · typ 15 · max 28 kΩ13
Input Resistance Deviation ΔRiBetween CANH and CANL; VCANH = VCANL = 4V (Note 1)min -1 · typ 0 · max 1 %13
Input Resistance Deviation ΔRiBetween CANH and CANL; –2V ≤ VCANH ≤ +7V, –2V ≤ VCANL ≤ +7V (Note 3)min -1 · typ 0 · max 1 %13
Differential Input Resistance Ri(dif)VCANH = VCANL = 4V (Note 1)min 18 · typ 30 · max 56 kΩ13
Differential Input Resistance Ri(dif)–2V ≤ VCANH ≤ +7V, –2V ≤ VCANL ≤ +7V (Note 3)min 18 · typ 30 · max 56 kΩ13
Common-mode Input Capacitance Ci(cm)f = 500 kHz, CANH and CANL referred to GND (Note 3)max 20 pF13
Differential Input Capacitance Ci(dif)f = 500kHz, between CANH and CANL (Note 3)max 10 pF13
Differential Bus Voltage Range for RECESSIVE State Detection VDiff_recNormal mode (HSC); –27V ≤ VCANH ≤ +27V, –27V ≤ VCANL ≤ +27V (Note 3)min -3 · max 0.5 V14
Differential Bus Voltage Range for RECESSIVE State Detection VDiff_recStandby mode (WUC); –27V ≤ VCANH ≤ +27V, –27V ≤ VCANL ≤ +27V (Note 3)min -3 · max 0.4 V14
Differential Bus Voltage Range for DOMINANT State Detection VDiff_domNormal mode (HSC); –27V ≤ VCANH ≤ +27V, –27V ≤ VCANL ≤ +27V (Note 3)min 0.9 · max 8 V14
Differential Bus Voltage Range for DOMINANT State Detection VDiff_domStandby mode (WUC); –27V ≤ VCANH ≤ +27V, –27V ≤ VCANL ≤ +27V (Note 3)min 1.15 · max 8 V14
Delay Time from TXD to Bus Dominant td(TXD-busdom)Normal mode (Note 2)min 40 · max 130 ns14
Delay Time from TXD to Bus Recessive td(TXD-busrec)Normal mode (Note 2)min 40 · max 130 ns14
Delay Time from Bus Dominant to RXD td(busdom-RXD)Normal mode (Note 2)min 20 · max 100 ns14
Delay Time from Bus Recessive to RXD td(busrec-RXD)Normal mode (Note 2)min 20 · max 100 ns14
Propagation Delay from TXD to RXD tPD(TXD-RXD)Normal mode, Rising edge at pin TXD; RL = 60Ω, CL = 100 pFmin 40 · max 210 ns14
Propagation Delay from TXD to RXD tPD(TXD-RXD)Normal mode, Falling edge at pin TXD; RL = 60Ω, CL = 100 pFmin 40 · max 200 ns14
Propagation Delay from TXD to RXD tPD(TXD-RXD)Normal mode, Rising edge at pin TXD; RL = 150Ω, CL = 100 pF (Note 3)max 300 ns14
Propagation Delay from TXD to RXD tPD(TXD-RXD)Normal mode, Falling edge at pin TXD; RL = 150Ω, CL = 100pF (Note 3)max 300 ns14
TXD Dominant Time-Out Time tto(dom)TXDVTXD = 0V, Normal modemin 0.8 · max 3 ms14
Bus Wake-up Time-Out Time tWakeStandby modemin 0.8 · max 3 ms14
Min. Dominant/Recessive Bus Wake-up Time tFilterStandby modemin 0.5 · typ 3 · max 3.8 us14
Delay Time for Standby Mode to Normal Mode Transition tdel(stby-norm)Falling edge at pin STBYmax 47 us14
Delay Time for Normal Mode to Standby Mode Transition tdel(norm-stby)Rising edge at pin STBY (Note 3)max 5 us14
Debouncing Time for Recessive Clamping State Detection tRC_detV(CANH-CANL) > 900mV; RXD = high (Note 3)typ 90 ns15
Recessive Bit Time on Pin RXD tBit(RXD)Normal mode, tBit(TXD) = 500 ns; RL = 60Ω, CL = 100 pF (Note 1)min 400 · max 550 ns15
Recessive Bit Time on Pin RXD tBit(RXD)Normal mode, tBit(TXD) = 200 ns; RL = 60Ω, CL = 100 pFmin 120 · max 220 ns15
Recessive Bit Time on the Bus tBit(Bus)Normal mode, tBit(TXD) = 500 ns; RL = 60Ω, CL = 100 pF (Note 1)min 435 · max 530 ns15
Recessive Bit Time on the Bus tBit(Bus)Normal mode, tBit(TXD) = 200 ns; RL = 60Ω, CL = 100 pFmin 155 · max 210 ns15
Receiver Timing Symmetry ΔtRecNormal mode, tBit(TXD) = 500 ns; ΔtRec = tBit(RXD)–tBit(Bus); RL = 60Ω, CL = 100 pF (Note 1)min -65 · max 40 ns15
Receiver Timing Symmetry ΔtRecNormal mode, tBit(TXD) = 200 ns; ΔtRec = tBit(RXD)–tBit(Bus); RL = 60Ω, CL = 100 pFmin -45 · max 15 ns15
Thermal Resistance Virtual Junction to Ambient RthvJASOIC8 Packagetyp 145 K/W15
Thermal Shutdown of the Bus Drivers for ATA6562-GAQW1, ATA6563-GAQW1 (Grade 1) TVJsdSOIC8 Package; ATA6563-GAQW1 (Grade 1)min 150 · max 195 °C15
Thermal Shutdown Hysteresis TvJsd_hysSOIC8 Packagetyp 15 °C15
Debouncing Time for Recessive Clamping State Detection tRC_detV(CANH-CANL) > 900mV, RXD = high; design parametertyp 90 ns15
Recessive Bit Time on Pin RXD tBit(RXD)Normal mode, tBit(TXD) = 500 ns, RL = 60Ω, CL = 100 pF; Note 1min 400 · max 550 ns15
Recessive Bit Time on Pin RXD tBit(RXD)Normal mode, tBit(TXD) = 200 ns, RL = 60Ω, CL = 100 pFmin 120 · max 220 ns15
Recessive Bit Time on the Bus tBit(Bus)Normal mode, tBit(TXD) = 500 ns, RL = 60Ω, CL = 100 pF; Note 1min 435 · max 530 ns15
Recessive Bit Time on the Bus tBit(Bus)Normal mode, tBit(TXD) = 200 ns, RL = 60Ω, CL = 100 pFmin 155 · max 210 ns15
Receiver Timing Symmetry ΔtRecNormal mode, tBit(TXD) = 500 ns, ΔtRec = tBit(RXD)–tBit(Bus), RL = 60Ω, CL = 100 pF; Note 1min -65 · max 40 ns15
Receiver Timing Symmetry ΔtRecNormal mode, tBit(TXD) = 200 ns, ΔtRec = tBit(RXD)–tBit(Bus), RL = 60Ω, CL = 100 pFmin -45 · max 15 ns15
Thermal Shutdown of the Bus Drivers for ATA6562-GAQW1, ATA6563-GAQW1 (Grade 1) TVJsdATA6563-GAQW1 (Grade 1), SOIC8 Packagemin 150 · max 195 °C15

Pins, by the datasheet

8
1 TXD
Transmit data input. · p. 9
2 GND
Ground. · p. 9
3 VCC
Supply voltage. · p. 9
4 RXD
Receive data output; reads out data from the bus lines. · p. 9
5 VIO
Supply voltage for I/O level adapter; connect to the microcontroller supply. · p. 9
6 CANL
Low-level CAN bus line. · p. 9
7 CANH
High-level CAN bus line. · p. 9
8 STBY
Standby mode control input. · p. 9

Ordering codes, by the datasheet

4
ATA6563-GAQW1
SOIC8 · Grade 1; standby mode and VIO pin for compatibility with 3.3V and 5V microcontrollers. · p. 2
ATA6563-GAQW0
8-Lead SOIC · Temperature Grade 0 (-40°C to +150°C); 330 mm tape and reel; RoHS · p. 29
ATA6563-GBQW0
8-Lead VDFN · Temperature Grade 0 (-40°C to +150°C); 330 mm tape and reel; RoHS · p. 29
ATA6563-GBQW1
8-Lead VDFN · Temperature Grade 1 (-40°C to +125°C); 330 mm tape and reel; RoHS · p. 29

Open-source boards using it

5
  • 2 layers43.8 × 31.8 mmCbb, the printed circuit board in 3D

    Cbb

    0x007E/cbb

    CAN-Bus Bridge

    33 parts
  • 4 layers45.5 × 51 mmCanBus Sniffer v1, the printed circuit board in 3D

    CanBus Sniffer v1

    Kubakl11/CAN_Bus_Sniffer_BP

    The bachelor’s thesis is focused on the design and implementation of a system for CAN bus data analysis for automotive monitoring.

    78 parts
  • 2 layers132 × 56 mmDashboard, the printed circuit board in 3D

    Dashboard

    marcutudor79/electronic-module-for-the-dashboard-of-upbdrive-racing-car

    My Bachelor's degree that consists of the electronic module for the Formula Student race car and it's testing module

    127 partsApache-2.0
  • 2 layers95.9 × 90.2 mmDat, the printed circuit board in 3D

    Dat

    timothy-joseph/timotelemetry_timounu

    Formula Student Telemetry system I've developed in my first year of University at UPB Drive

    86 partsGPL-3.0
  • 2 layers55.9 × 30.5 mmCanfd transducer, the printed circuit board in 3D

    Canfd transducer

    Wolgamonox/me410-rowing

    Firmware and electronics for the Syncrower project (EPFL course ME410)

    12 parts

Parts like it

8

Questions

Is there a KiCad symbol and footprint for the ATA6563-GAQW1?

Yes. The symbol is EasyEDA_Cloud:ATA6563-GAQW1 and the footprint Package_SO:SOIC-8_3.9x4.9mm_P1.27mm, both drawn on this page. PCBKit places them on a board for you when you design with it.

What package is the ATA6563-GAQW1?

SOIC-8, with 8 pins. Its footprint is drawn on this page.

Where is the ATA6563-GAQW1 datasheet?

Microchip Technology publishes it: the Datasheet link on this page opens it.

Where can I order the ATA6563-GAQW1?

JLCPCB lists it as part C5127614, with 4,065 in stock; the sellers' links on this page open their listings.

What can replace the ATA6563-GAQW1?

Parts like it in the library: the TJA1051T/3/1J by NXP Semiconductors, the SN65HVD230D by Texas Instruments, the TJA1042T/1J by NXP Semiconductors and the CA-IF1051S by Chipanalog. Check their datasheets: a part that fits the footprint may still differ in its ratings.

Which open-source boards use the ATA6563-GAQW1?

5 boards in 5 repositories on GitHub; the most starred are listed on this page, with their KiCad files.