ES1J

MDD

-55℃~+150℃ 1 Independent 1.7V@1A 1A 35ns 5uA@600V 600V SMA Fast Recovery / High Efficiency Diodes ROHS

Extended

Category: Diodes Rectifiers Fast Recovery
Package: SMA(DO-214AC)
Pins: 2

Overview

The ES1J is a diodes Rectifiers Fast Recovery made by MDD in a SMA(DO-214AC) package with 2 pins. -55℃~+150℃ 1 Independent 1.7V@1A 1A 35ns 5uA@600V 600V SMA Fast Recovery / High Efficiency Diodes ROHS.

PCBKit's library has its KiCad symbol (Device:D, from KiCad's library) and its footprint (Diode_SMD:D_SMA, from KiCad's library), ready for a KiCad board. 623,892 are in stock at JLCPCB (part C412438). 21 open-source boards in 18 repositories on GitHub use it.

Symbol

Device:DFrom KiCad's library

Footprint

Diode_SMD:D_SMAFrom KiCad's library

From the datasheet

Reverse voltage, most: 600 V · max repetitive peak reverse voltage · p. 1
Forward current, most: 1 A · max average forward rectified current at TL=55 C · p. 1
Forward voltage: 1.7 V · max instantaneous forward voltage at 1.0 A · p. 1
Junction to air (DO-214AC/SMA): 60 K/W · typical, PCB mounted with 0.2x0.2 inch copper pad areas · p. 1
Junction, hottest: 150 °C · max operating junction temperature · p. 1

What it is and has

Flammability classification: 94V-0 · p. 1
Junction: Glass passivated chip junction · p. 1
Package: JEDEC DO-214AC molded plastic body over passivated chip · p. 1

Specifications

Parameter	Conditions	As printed	Page
Maximum repetitive peak reverse voltage VRRM	ES1J; 25 C ambient unless otherwise specified	max 600 VOLTS	1
Maximum RMS voltage VRMS	ES1J; 25 C ambient unless otherwise specified	max 420 VOLTS	1
Maximum DC blocking voltage VDC	ES1J; 25 C ambient unless otherwise specified	max 600 VOLTS	1
Maximum average forward rectified current I(AV)	ES1J; at TL=55 C; single phase half-wave 60Hz, resistive or inductive load; for capacitive load current derate by 20%	max 1 Amp	1
Peak forward surge current IFSM	ES1J; 8.3ms single half sine-wave superimposed on rated load (JEDEC Method)	max 30 Amps	1
Maximum instantaneous forward voltage at 1.0A VF	ES1J; 25 C ambient	max 1.7 Volts	1
Maximum DC reverse current at rated DC blocking voltage IR	ES1J; TA=25 C	max 5 uA	1
Maximum DC reverse current at rated DC blocking voltage IR	ES1J; TA=100 C	max 50 uA	1
Maximum reverse recovery time trr	ES1J; IF=0.5A, IR=1.0A, Irr=0.25A	max 35 ns	1
Typical junction capacitance CJ	ES1J; measured at 1MHz and applied reverse voltage of 4.0V D.C.	typ 15 pF	1
Typical thermal resistance RθJA	ES1J; DO-214AC/SMA; P.C.B. mounted with 0.2x0.2 inch (5.0x5.0mm) copper pad areas	typ 60 C/W	1
Operating junction and storage temperature range TJ,TSTG	ES1J	min -50 · max 150 C	1

Parameters

Current - Rectified: 1A
Diode Configuration: 1 Independent
Forward Current(If): 1A
Forward Voltage (Vf@If): 1.7V@1A
Junction Temperature(Max): 150℃
Operating Junction Temperature Range: -55℃~+150℃
Operating Temperature: -55℃~+150℃@(Tj)
Reverse Leakage Current: 5μA@600V
Reverse Leakage Current (Ir): 5uA@600V
Reverse Recovery Time (trr): 35ns
Reverse Voltage: 600V
Thermal Resistance(Junction to Ambient): 60℃/W
Voltage - DC Reverse(Vr): 600V
Voltage - Forward(Vf): 1.7V
Voltage - Forward(Vf@If): 1.7V@1A

Order codes

Pinout

The pins of the ES1J
Pin	Name	Type
1	K	Passive
2	A	Passive

Open-source boards using it

All 21

4 layers155 × 75 mm
GTI V5
fotherja/Grid_Tie_Inverter_V5
Please refer to my site ( www.jamesfotherby.com ) where this project is being documented in detail
165 parts47MIT
2 layers35 × 20 mm
T3pa loadcell mod v2
foriequal0/t3pa-loadcell-mod
Thrustmaster T3PA pedal load cell mod without a dead zone
23 parts5
4 layers109 × 231.4 mm
High voltage servo drive 3ch
ExcessiveOverkill/hvsd-3ch

487 parts4
2 layers100 × 85 mm
Dekatron
kuvychko/universal-nixie-display
Six IN-14 Nixie tubes, an A101 dekatron and an ESP32 touchscreen in one desktop display: a clock, timer and toy, and a numeric display for a computer over USB.
165 parts1
4 layers44 × 22 mm
Doublebridgeright v8
supernova-10/Kubits-programmable-magnets
Kubit is my Final Year Project (FYP) — a modular reconfigurable robot that uses programmable magnets, gears, and custom PCB-based control to achieve untethered actuation and reconfiguration.
32 parts1
2 layers140 × 50 mm
Yarrow counter basic
alplix/yarrow
Open firmware for the FNIRSI GC-03 radiation detector
62 partsGPL-3.0
2 layers
Sih
arthithadee/Sonar_transmitter
AZHAI is a software-defined sonar transmitter firmware designed for autonomous underwater vehicles (AUVs).
73 parts
2 layers70 × 54.5 mm
Reckoner
blind-reckoning/Reckoner
Turns press-and-hold motorised blinds into Home Assistant covers. One Reckoner per blind, hidden in the wall box behind the buttons you already have.
92 partsCERN-OHL-S-2.0

Show this part on your page

A live frame, for any web page

<iframe src="https://pcbkit.io/embed/parts/mdd/ES1J" title="ES1J in PCBKit" width="100%" height="480" style="border:0;border-radius:12px" allow="fullscreen" loading="lazy"></iframe>

A picture

<img src="https://pcbkit.io/embed/parts/mdd/ES1J.jpg" alt="ES1J" width="1200" height="900">

A picture that opens the part, for a README

[![ES1J](https://pcbkit.io/embed/parts/mdd/ES1J.jpg?size=s)](https://pcbkit.io/parts/mdd/ES1J)

Questions

Is there a KiCad symbol and footprint for the ES1J?

Yes. The symbol is Device:D and the footprint Diode_SMD:D_SMA, both drawn on this page. PCBKit places them on a board for you when you design with it.

What package is the ES1J?

SMA(DO-214AC), with 2 pins. Its footprint is drawn on this page.

Where is the ES1J datasheet?

MDD publishes it: the Datasheet link on this page opens it.

Where can I order the ES1J?

JLCPCB lists it as part C412438, with 623,892 in stock; the sellers' links on this page open their listings.

What can replace the ES1J?

Parts like it in the library: the US1J-A by FMS, the ES1J by Yenji Elec, the RS1M by Yenji Elec and the US1M by Yenji Elec. Check their datasheets: a part that fits the footprint may still differ in its ratings.

Which open-source boards use the ES1J?

21 boards in 18 repositories on GitHub; the most starred are listed on this page, with their KiCad files.