Skip to the content
12345

AL8860WT

Diodes IncorporatedExtended

-40℃~+85℃ 1 1A 1MHz 4.5V~40V 5% Analog、PWM Buck Built-in DC-DC Short Circuit Protection、Over-Temperature Protection (OTP)、LED open-circuit protection、Built-in soft-start TSOT-25 LED Drivers ROHS

Part id
diodes/AL8860WT
Category
LED Drivers
Package
TSOT-25
Pins
5
In stock
5 at JLCPCB (C125330)
Used on
10 open-source boards

Overview

The AL8860WT is a LED Driver made by Diodes Incorporated in a TSOT-25 package with 5 pins. -40℃~+85℃ 1 1A 1MHz 4.5V~40V 5% Analog、PWM Buck Built-in DC-DC Short Circuit Protection、Over-Temperature Protection (OTP)、LED open-circuit protection、Built-in soft-start TSOT-25 LED Drivers ROHS.

PCBKit's library has its KiCad symbol (Driver_LED:AL8860WT, from KiCad's library) and its footprint (Package_TO_SOT_SMD:TSOT-23-5, from KiCad's library), ready for a KiCad board. 5 are in stock at JLCPCB (part C125330). 10 open-source boards in 8 repositories on GitHub use it.

Symbol

1SW2GND3CTRL4SET5VIN
Driver_LED:AL8860WTFrom KiCad's library

Footprint

12345
Package_TO_SOT_SMD:TSOT-23-5From KiCad's library

From the datasheet

12
Supply, least
4.5 V · VIN, recommended operating min · p. 3
Supply, most
40 V · VIN, recommended operating max · p. 3
Supply, absolute maximum
42 V · VIN, absolute max · p. 3
Works from
-40 °C · Operating ambient temperature min · p. 3
Works up to
85 °C · Operating ambient temperature max · p. 3
Junction, hottest
150 °C · Junction temperature absolute max · p. 3
Takes working
550 µA · Quiescent current typical, CTRL floating, VIN = 16V · p. 4
Takes asleep
50 µA · Shutdown supply current typical, CTRL grounded · p. 4
Gives
1 A · Continuous output current max, TSOT25 · p. 3
Switches at
250 kHz · Operating frequency typical, VIN = 16V, VO = 9.6V, ILED = 1A · p. 4
Junction to air (TSOT25)
147 K/W · Junction to ambient, specified PCB mounting · p. 3
Junction to case (TSOT25)
27 K/W · Junction to case · p. 3

What it is and has

9
Internal power switch
40V NDMOS · p. 1
Output current accuracy
5% typical · p. 1
Analog dimming range
5% to 100% · p. 1
Soft-start
Supported · p. 1
Efficiency
Up to 97% · p. 1
Protection
LED short protection · p. 1
Protection
Open-circuit LED protection · p. 1
Protection
Overtemperature protection · p. 1
Package options
TSOT25 and MSOP-8EP · p. 1

Around it

9
cap 10μF or higher
between VIN and GND; X7R ceramic capacitor close to device. · p. 2
cap 4.7μF to 10μF
between VIN and GND; Common input decoupling values; use low ESR and place close to the IC. · p. 12
cap 1.5ms/nF
between CTRL and GND; Optional soft-start capacitor; value states typical additional delay per capacitance. · p. 12
ind 33μH to 100μH
between LED cathode and SW; Use saturation current above peak output current and continuous rating above mean output current; mount close to device. · p. 13
diode Schottky
between SW and VIN; D1 freewheeling diode, anode at SW; fast, low capacitance and low reverse leakage. Current ratings must exceed coil peak and output load currents. · p. 12
res 0.1 Ω
between VIN and SET; Current-setting resistor for nominal average output current of 1000mA, CTRL floating. · p. 11
res 0.13 Ω
between VIN and SET; Current-setting resistor for nominal average output current of 760mA, CTRL floating. · p. 11
res 0.15 Ω
between VIN and SET; Current-setting resistor for nominal average output current of 667mA, CTRL floating. · p. 11
res 0.3 Ω
between VIN and SET; Current-setting resistor for nominal average output current of 333mA, CTRL floating. · p. 11

Specifications

35
ParameterConditionsAs printedPage
Human Body Model ESD Protection ESD HBMTA = +25°Cmax 2.5 kV3
Machine Model ESD Protection ESD MMTA = +25°Cmax 200 V3
Input Voltage VINTA = +25°Cmin -0.3 · max 42 V3
SW, SET Pin Voltage VSW, VSETTA = +25°Cmin -0.3 · max 42 V3
CTRL Pin Voltage VCTRLTA = +25°Cmin -0.3 · max 6 V3
Operating Junction Temperature TJmax 150 °C3
Storage Temperature Range TSTGmin -65 · max 150 °C3
Lead Temperature (Soldering, 10s) TLEADSoldering, 10smax 260 °C3
Thermal Resistance (Junction to Ambient) θJATSOT25 (Note 5)max 147 °C/W3
Thermal Resistance (Junction to Case) θJCTSOT25 (Note 5)max 27 °C/W3
Input Voltage VINTA = +25°Cmin 4.5 · max 40 V3
Switching Frequency fSWTA = +25°Cmax 1 MHz3
Continuous Output Current IOUTTSOT25max 1 A3
Recommended Analog Dimming RangeTA = +25°Cmin 5 · max 100 %3
Operating Ambient Temperature TAmin -40 · max 85 °C3
Operating Junction Temperature TJmin -40 · max 125 °C3
Input Voltage VINTA = +25°Cmin 4.5 · max 40 V4
Quiescent Current IQCTRL Pin Floating, VIN = 16Vtyp 0.55 mA4
Shutdown Supply Current ISHDNCTRL Pin Groundedtyp 50 · max 80 uA4
Mean Current Sense Threshold Voltage VSENSEMeasured on SET Pin with Respect to VINmin 96 · typ 100 · max 104 mV4
SET Pin Input Current ISETVSET = VIN -0.1typ 8 uA4
CTRL Range on CTRL Pin VENFor Analog Dimmingmin 0.3 · max 2.5 V4
DC Voltage on CTRL Pin to Enable VEN(ON)VEN Risingtyp 0.25 V4
DC Voltage on CTRL Pin to Disable VEN(OFF)VEN Fallingtyp 0.2 V4
SW Switch On Resistance RSW@ISW = 100mAtyp 0.2 Ω4
SW Switch Leakage Current ISW(LEAK)max 5 uA4
Soft-Start Time tSSVIN = 16V, CEN = 1nFtyp 1.5 ms4
Operating Frequency fSWVIN = 16V, VO = 9.6V (3 LEDs); L = 47uF, ΔI = 0.25A (ILED = 1A)typ 250 kHz4
Recommended Minimum Switch ON Time tON_RECFor 4% Accuracytyp 500 ns4
Recommended Maximum Switch Frequency fSW(MAX)max 1 MHz4
Max Duty Cycle DSW(MAX)typ 98 %4
Recommended Duty Cycle Range DSWmin 25 · max 75 %4
Internal Comparator Propagation Delay (Note 7) tPDGuaranteed by designtyp 45 ns4
Overtemperature Protection TOTPtyp 150 °C4
Temperature Protection Hysteresis TOTP_HYStyp 30 °C4

Pins, by the datasheet

5
1 SW
Drain of NDMOS switch. · p. 2
2 GND
Ground (0V). · p. 2
3 CTRL
On/Off and brightness control; leave floating for normal operation, drive below 0.2V to turn off, or apply DC or PWM dimming. Connect a capacitor to ground to increase soft-start time. · p. 2
4 SET
Connect resistor RS to VIN to define nominal average output current: IOUT_NOM = 0.1/Rs. · p. 2
5 VIN
Input voltage (4.5V to 40V); decouple to ground with a 10uF or higher X7R ceramic capacitor close to the device. · p. 2

Ordering codes, by the datasheet

2
AL8860WT-7
TSOT25 · 3000 units, Tape & Reel; continuous output current up to 1A. · p. 15
AL8860MP-13
MSOP-8EP · 2500 units, Tape & Reel; continuous output current up to 1.5A. · p. 15

Open-source boards using it

10See all 10
  • 2 layers58.3 × 15 mmVape light, the printed circuit board in 3D

    Vape light

    sbyd-space/vape-light

    An educational DIY kit for converting a disposable vape into a rechargeable flashlight

    46 parts4CERN-OHL-P-2.0
  • 2 layers53.3 × 31.8 mmConstant current driver AL8860, the printed circuit board in 3D

    Constant current driver AL8860

    DIaLOGIKa-GmbH/pcb_constant-current-driver

    Testing PCBs for different constant current driver ICs

    22 parts3MIT
  • 2 layers49.4 × 95.7 mmPhysiowand, the printed circuit board in 3D

    Physiowand

    1tsMS/Physiowand

    91 parts
  • 4 layers39 × 119.5 mmFieldcam, the printed circuit board in 3D

    Fieldcam

    EmbryoPhenomics/FieldCam

    Submersible field camera and sensor instrument

    136 parts
  • 4 layers100 × 100 mmRipple tank pcb, the printed circuit board in 3D

    Ripple tank pcb

    practable/ripple-tank

    Software and documentation for the ripple tank remote lab project

    111 partsAGPL-3.0
  • 4 layers40 × 130 mmWurtelvin, the printed circuit board in 3D

    Wurtelvin

    samvandenabeele/wurtelvin

    95 parts
  • 2 layers100 × 96 mmBacklight, the printed circuit board in 3D

    Backlight

    jackw01/scanlight

    A better light source for scanning color negative film

    59 parts397CERN-OHL-W-2.0
  • 2 layers100 × 96 mmBacklight, the printed circuit board in 3D

    Backlight

    jackw01/scanlight

    A better light source for scanning color negative film

    69 parts397CERN-OHL-W-2.0

Parts like it

8

Questions

Is there a KiCad symbol and footprint for the AL8860WT?

Yes. The symbol is Driver_LED:AL8860WT and the footprint Package_TO_SOT_SMD:TSOT-23-5, both drawn on this page. PCBKit places them on a board for you when you design with it.

What package is the AL8860WT?

TSOT-25, with 5 pins. Its footprint is drawn on this page.

Where is the AL8860WT datasheet?

Diodes Incorporated publishes it: the Datasheet link on this page opens it.

Where can I order the AL8860WT?

JLCPCB lists it as part C125330, with 5 in stock; the sellers' links on this page open their listings.

What can replace the AL8860WT?

Parts like it in the library: the AL8861WT by Diodes Incorporated, the PAM2804AAB010 by Diodes Incorporated, the ZXLD1362ET5TA by Diodes Incorporated and the PAM2804AAB010(MS) by MSKSEMI. Check their datasheets: a part that fits the footprint may still differ in its ratings.

Which open-source boards use the AL8860WT?

10 boards in 8 repositories on GitHub; the most starred are listed on this page, with their KiCad files.