Skip to the content
12345

PAM2804AAB010

Diodes IncorporatedExtended

-40℃~+85℃ 1 1.5MHz 1A 2.5V~6V Buck Built-in Over-Temperature Protection (OTP)、Short-Circuit Protection PWM TSOT-25 LED Drivers ROHS

Part id
diodes/PAM2804AAB010
Category
LED Drivers
Package
TSOT-25
Pins
5
In stock
15,542 at JLCPCB (C71463)
Used on
4 open-source boards

Overview

The PAM2804AAB010 is a LED Driver made by Diodes Incorporated in a TSOT-25 package with 5 pins. -40℃~+85℃ 1 1.5MHz 1A 2.5V~6V Buck Built-in Over-Temperature Protection (OTP)、Short-Circuit Protection PWM TSOT-25 LED Drivers ROHS.

PCBKit's library has its KiCad symbol (Horizon_ic:PAM2804AAB010, from Horizon) and its footprint (Package_TO_SOT_SMD:TSOT-23-5, from KiCad's library), ready for a KiCad board. 15,542 are in stock at JLCPCB (part C71463). 4 open-source boards in 4 repositories on GitHub use it.

Symbol

3SW2GND5FB4VIN1EN
Horizon_ic:PAM2804AAB010From Horizon

Footprint

12345
Package_TO_SOT_SMD:TSOT-23-5From KiCad's library

From the datasheet

13
Supply, least
2.5 V · VIN, recommended operating min · p. 3
Supply, most
6 V · VIN, recommended operating max · p. 3
Supply, absolute maximum
6.5 V · VIN, absolute max · p. 2
Works from
-40 °C · Operating ambient min · p. 3
Works up to
85 °C · Operating ambient max · p. 3
Junction, hottest
150 °C · Junction temperature absolute max · p. 2
Takes working
180 µA · VIN quiescent current, no load, typical · p. 3
Takes asleep
1 µA · Shutdown current, VEN = 0V, max · p. 3
Gives
1 A · LED output current max, subject to package power dissipation · p. 1
Feedback reference
100 mV · Regulated feedback voltage typical · p. 3
Switches at
1.5 MHz · Oscillator frequency, VO = 100%, typical · p. 3
Junction to case (TSOT25)
130 K/W · Junction to case thermal resistance max · p. 3
Junction to air (TSOT25)
250 K/W · Junction to ambient thermal resistance max · p. 3

What it is and has

9
Efficiency
Up to 93% · p. 1
Rectifier
Internal synchronous rectifier · p. 1
Soft start
Supported · p. 1
Protection
Undervoltage lockout · p. 1
Protection
Short LED protection · p. 1
Protection
Open LED protection · p. 1
Protection
Thermal shutdown · p. 1
Package
5-pin TSOT25 · p. 1
Package material
Pb-free · p. 1

Around it

4
ind 1μH to 4.7μH
between SW and LED supply; Choose for desired ripple current; low DC resistance improves efficiency. · p. 6
res 0.286 Ω
between FB and GND; Current sense resistor for 350 mA LED current; keep its ground trace short, direct and wide. · p. 7
res 0.143 Ω
between FB and GND; Current sense resistor for 700 mA LED current; keep its ground trace short, direct and wide. · p. 7
res 0.1 Ω
between FB and GND; Current sense resistor for 1,000 mA LED current; keep its ground trace short, direct and wide. · p. 7

Specifications

27
ParameterConditionsAs printedPage
Input Pin VoltageTA = +25°C; voltages with respect to groundmin -0.3 · max 6.5 V2
EN, FB Pin VoltageTA = +25°C; upper limit VINmin -0.3 V2
SW Pin VoltageTA = +25°C; upper limit VIN +0.3 Vmin -0.3 V2
Junction Temperature Rangemax 150 °C2
Storage Temperature Rangemin -65 · max 150 °C2
Soldering Temperature5secmax 300 °C2
Supply VoltageTA = +25°Cmin 2.5 · max 63
Operation Temperature Rangemin -40 · max 85 °C3
Junction Temperature Rangemin -40 · max 125 °C3
Thermal Resistance (Junction to Case) θJCTSOT25 (Note 1)max 130 °C/W3
Thermal Resistance (Junction to Ambient) θJATSOT25max 250 °C/W3
Internal Power Dissipation PDTSOT25max 400 mW3
Input Voltage Range VINTA = +25°C, real WLED load, L = 4.7uH, CIN = 10uF, CO = 10uFmin 2.5 · max 6 V3
Regulated Feedback Voltage VFBTA = +25°C, VIN = 4.2V, real WLED load, L = 4.7uH, CIN = 10uF, CO = 10uFmin 0.095 · typ 0.1 · max 0.105 V3
Peak Inductor Current IPKVIN = 5V; TA = +25°C, real WLED load, L = 4.7uH, CIN = 10uF, CO = 10uFtyp 1.5 A3
Quiescent Current IQNo Load; TA = +25°C, VIN = 4.2V, L = 4.7uH, CIN = 10uF, CO = 10uFtyp 180 uA3
Shutdown Current ISDVEN = 0V; TA = +25°C, VIN = 4.2V, real WLED load, L = 4.7uH, CIN = 10uF, CO = 10uFmax 1 uA3
Oscillator Frequency fOSCVO = 100%; TA = +25°C, VIN = 4.2V, real WLED load, L = 4.7uH, CIN = 10uF, CO = 10uFmin 1.2 · typ 1.5 · max 1.8 MHz3
Drain-Source On-State Resistance RDS(ON)P MOSFET; IDS = 100mA; TA = +25°C, VIN = 4.2Vtyp 0.3 · max 0.45 Ω3
Drain-Source On-State Resistance RDS(ON)N MOSFET; IDS = 100mA; TA = +25°C, VIN = 4.2Vtyp 0.35 · max 0.5 Ω3
SW Leakage Current ILSWTA = +25°C, VIN = 4.2V, real WLED load, L = 4.7uH, CIN = 10uF, CO = 10uF; typical is ±0.01 uAtyp 0.01 · max 1 uA3
High Efficiency ηTA = +25°C, VIN = 4.2V, real WLED load, L = 4.7uH, CIN = 10uF, CO = 10uFtyp 93 %3
EN Threshold High VEHTA = +25°C, VIN = 4.2Vmin 1.5 V3
EN Threshold Low VELTA = +25°C, VIN = 4.2Vmax 0.3 V3
EN Leakage Current IENTA = +25°C, VIN = 4.2V; typical is ±0.01 uAtyp 0.01 uA3
Over-Temperature Protection OTPVIN = 4.2Vtyp 150 °C3
OTP Hysteresis OTHVIN = 4.2Vtyp 30 °C3

Pins, by the datasheet

5
1 EN
Enable control input; above 1.5V enables the chip and below 0.3V shuts down the device. · p. 2
2 GND
Ground. · p. 2
3 SW
The drains of the internal main and synchronous power MOSFET. · p. 2
4 VIN
Chip main power supply pin. · p. 2
5 FB
Feedback voltage to internal error amplifier; threshold voltage is 0.1V. · p. 2

Ordering codes, by the datasheet

1
PAM2804AAB010
TSOT25 · 5 pins, 0.1V feedback voltage, 3,000 units/tape & reel · p. 8

Open-source boards using it

4
  • 2 layers112 × 48.8 mmPCBmain, the printed circuit board in 3D

    PCBmain

    MagnusLab/Magnus-qPCR

    An open, portable and low cost qPCR machine.

    63 parts7GPL-3.0
  • 2 layers55.6 × 55.8 mmHikari, the printed circuit board in 3D

    Hikari

    goodmicros/hikari

    wled party beacon

    58 parts6
  • 4 layers43 × 62 mmSmall display, the printed circuit board in 3D

    Small display

    airball-aero/airball-hardware

    49 partsMIT
  • 4 layers48 × 40.1 mmLED Revised New, the printed circuit board in 3D

    LED Revised New

    DeanElec/Compact-high-efficiency-illumination-systems-for-in-orbit-microscopy

    Presents all data associated with the development of my thesis for a 3rd year final year project at the University of Nottingham, centred around a multimodal condenser free microscope for use on a CubeSat satellite.

    121 partsGPL-3.0

Parts like it

8

Questions

Is there a KiCad symbol and footprint for the PAM2804AAB010?

Yes. The symbol is Horizon_ic:PAM2804AAB010 and the footprint Package_TO_SOT_SMD:TSOT-23-5, both drawn on this page. PCBKit places them on a board for you when you design with it.

What package is the PAM2804AAB010?

TSOT-25, with 5 pins. Its footprint is drawn on this page.

Where is the PAM2804AAB010 datasheet?

Diodes Incorporated publishes it: the Datasheet link on this page opens it.

Where can I order the PAM2804AAB010?

JLCPCB lists it as part C71463, with 15,542 in stock; the sellers' links on this page open their listings.

What can replace the PAM2804AAB010?

Parts like it in the library: the AL8861WT by Diodes Incorporated, the ZXLD1362ET5TA by Diodes Incorporated, the PAM2804AAB010(MS) by MSKSEMI and the TMI5102 by TMI. Check their datasheets: a part that fits the footprint may still differ in its ratings.

Which open-source boards use the PAM2804AAB010?

4 boards in 4 repositories on GitHub; the most starred are listed on this page, with their KiCad files.