Skip to the content
1234567891011121314

AS5048B-HTSP-500

Advanced Monolithic SystemsExtended

-40℃~+150℃ 0°~360° 1.2mm 15mA 3V~3.6V、4.5V~5.5V 4.4mm 5mm I2C Magnetic rotary position sensor No TSSOP-14 Position Sensors ROHS

Part id
ams/AS5048B-HTSP-500
Category
Position Sensors
Package
TSSOP-14
Pins
14
In stock
187 at JLCPCB (C2655184)
Used on
2 open-source boards

Overview

The AS5048B-HTSP-500 is a position Sensor made by Advanced Monolithic Systems in a TSSOP-14 package with 14 pins. -40℃~+150℃ 0°~360° 1.2mm 15mA 3V~3.6V、4.5V~5.5V 4.4mm 5mm I2C Magnetic rotary position sensor No TSSOP-14 Position Sensors ROHS.

PCBKit's library has its KiCad symbol (Sensor_Magnetic:AS5048B, from KiCad's library) and its footprint (Package_SO:TSSOP-14_4.4x5mm_P0.65mm, from KiCad's library), ready for a KiCad board. 187 are in stock at JLCPCB (part C2655184). 2 open-source boards in 2 repositories on GitHub use it.

Symbol

1SDA2SCL3A24A15TEST6TEST7TEST8TEST9TEST10TEST11VDD5V12VDD3V13GND14PWM
Sensor_Magnetic:AS5048BFrom KiCad's library

Footprint

1234567891011121314
Package_SO:TSSOP-14_4.4x5mm_P0.65mmFrom KiCad's library

From the datasheet

12
Supply, least
4.5 V · VDD5V, recommended operating min, 5V operation via LDO · p. 7
Supply, most
5.5 V · VDD5V, recommended operating max, 5V operation via LDO · p. 7
Supply, least
3 V · VDD5V tied to VDD3V, recommended operating min, 3.3V operation · p. 10
Supply, most
3.6 V · VDD5V tied to VDD3V, recommended operating max, 3.3V operation · p. 10
Supply, absolute maximum
7 V · VDD5V, absolute max · p. 6
Supply, absolute maximum
5 V · VDD3V, absolute max · p. 6
Works from
-40 °C · Ambient temperature min · p. 7
Works up to
150 °C · Ambient temperature max, 5V operation only · p. 7
Works up to
125 °C · Ambient temperature max, 3V operation · p. 7
Takes working
15 mA · Supply current max · p. 7
A pin gives at most
4 mA · Output current max, PWM and SDA · p. 7
Data rate, most
3.4 Mbit/s · I²C high-speed mode max · p. 21

What it is and has

7
Sensor
360° absolute angular position · p. 1
Resolution
14-bit, 0.0219°/LSB · p. 1
Interface
I²C and PWM · p. 1
Zero position
Programmable via I²C · p. 1
Magnetic immunity
Immune to external magnetic stray fields · p. 1
Package
TSSOP14 · p. 5
I²C speed
Up to 3.4MHz clock frequency · p. 21

Around it

2
cap 10 μF
between VDD3V and GND; Required buffer capacitor in 5V operation; VDD3V must not be left floating. · p. 10
cap 10μF
between VDD3V and GND; Also required when programming in 3V operation; programming supply must be at least 3.3V. · p. 28

Specifications

85
ParameterConditionsAs printedPage
DC supply voltage at VDD pin VDD5Vmin -0.3 · max 7 V6
DC voltage at VDD3V pin VDD3Vmin -0.3 · max 5 V6
DC voltage at GND pin GNDmin -0.3 · max 0.3 V6
Input current (latchup immunity) ISCRJedec 78min -100 · max 100 mA6
Electrostatic discharge ESDMIL 883 E method 3015; rating ±2 kVmax 2 kV6
Total power dissipation (all supplies and outputs) PTmax 150 mW6
Storage temperature TSTRGmin -55 · max 150 °C6
Package body temperature TBODYReflow peak soldering temperature; IPC/JEDEC J-STD-020max 260 °C6
Relative humidity non-condensing RHNCmin 5 · max 85 %6
Moisture sensitivity level MSLMaximum floor life time of 168hmax 36
Positive supply voltage VDD5V5V Operation via LDOmin 4.5 · max 5.5 V7
Positive supply voltage VDD3VLDO output voltagemin 3 · max 3.6 V7
Positive core supply voltage VDDCOREmin 3 · max 3.6 V7
Ambient temperature TAMBOnly for 5V operation; T_amb_max for 3V is 125°Cmin -40 · max 150 °C7
Supply current ISUPmax 15 mA7
Input leakage current lLEAKCMOS Digital Input with Schmitt Trigger: SCL, A1, A2max 1 uA7
Capacitive load CLCMOS Output: PWM, SDAmax 50 pF7
Output current IOUTCMOS Output: PWM, SDAmax 4 mA7
Magnetic input field BzVDD5V = 5V, T AMB = -40 to 150°C unless noted otherwisemin 30 · typ 50 · max 70 mT8
Output sampling rate fsampleVDD5V = 5V, T AMB = -40 to 150°C unless noted otherwisemin 10.2 · typ 11.25 · max 12.4 kHz8
Output resolution RESVDD5V = 5V, T AMB = -40 to 150°C unless noted otherwisetyp 14 Bit8
Sensor output noise Noise2.73LSB@14bit, rms value; VDD5V = 5V, T AMB = -40 to 150°Cmax 0.06 deg8
System propagation delay tpropVDD5V = 5V, T AMB = -40 to 150°C unless noted otherwisemin 90.7 · typ 100 · max 110.2 us8
PWM frequency fPWMVDD5V = 5V, T AMB = -40 to 150°C unless noted otherwisemin 0.907 · typ 1 · max 1.102 kHz8
Non-linearity, optimum placement of the magnet INLOPT @25ºC25ºC; maximum error ±0.8 degmax 0.8 deg8
Non-linearity optimum placement of the magnet over the full temperature range INL OPT+TEMPVDD5V = 5V, T AMB = -40 to 150°C; maximum error ±1 degmax 1 deg8
Non-linearity @ displacement of magnet and temperature -40ºC to 150ºC INL DIS+TEMPAssuming N35H magnet (D=8mm, H=3mm) 500um displacement in x and y z-distance @ 2000um; maximum error ±1.2 degmax 1.2 deg8
Startup time tstartupVDD5V = 5V, T AMB = -40 to 150°C unless noted otherwisemax 10 ms8
LOW-Level Input Voltage VILFS-mode+; maximum 0.3VDDCOREmin -0.5 V21
LOW-Level Input Voltage VILHS-mode CB=100pF; maximum 0.3VDDCOREmin -0.5 V21
LOW-Level Input Voltage VILHS-mode CB=400pF; maximum 0.3VDDCOREmin -0.5 V21
LOW-Level Output Current IOLFS-mode+; VOL = 0.4Vmin 20 mA21
Pull-up current of SCLH current source ICSHS-mode CB=100pFmin 3 · max 12 mA21
Pull-up current of SCLH current source ICSHS-mode CB=400pFmin 3 · max 12 mA21
Pulse Width of Spikes that must be suppressed by the Input Filter tSPFS-mode+; note 1max 50 ns21
Pulse Width of Spikes that must be suppressed by the Input Filter tSPHS-mode CB=100pFmax 10 ns21
Pulse Width of Spikes that must be suppressed by the Input Filter tSPHS-mode CB=400pFmax 10 ns21
Input Current at each I/O Pin IiFS-mode+; note 2min -10 · max 10 uA22
Input Current at each I/O Pin IiHS-mode CB=100pFmax 10 uA22
Input Current at each I/O Pin IiHS-mode CB=400pFmax 10 uA22
Total Capacitive Load for each Bus Line CBFS-mode+max 550 pF22
Total Capacitive Load for each Bus Line CBHS-mode CB=100pFmax 100 pF22
Total Capacitive Load for each Bus Line CBHS-mode CB=400pFmax 400 pF22
I/O Capacitance (SDA,SCL) CI/OFS-mode+max 10 pF22
I/O Capacitance (SDA,SCL) CI/OHS-mode CB=100pFmax 10 pF22
I/O Capacitance (SDA,SCL) CI/OHS-mode CB=400pFmax 10 pF22
SCL clock Frequency fSCLKFS-modemax 400 kHz22
SCL clock Frequency fSCLKHS-mode CB=100pFmax 3400 kHz22
SCL clock Frequency fSCLKHS-mode CB=400pF; note 5max 1700 kHz22
Bus Free Time; time between STOP and START Condition tBUFFS-modemin 500 ns22
Bus Free Time; time between STOP and START Condition tBUFHS-mode CB=100pFmin 500 ns22
Bus Free Time; time between STOP and START Condition tBUFHS-mode CB=400pF; note 5min 500 ns22
Hold Time; (Repeated) START Condition (1) tHD;STAFS-modemin 260 ns22
Hold Time; (Repeated) START Condition (1) tHD;STAHS-mode CB=100pFmin 160 ns22
Hold Time; (Repeated) START Condition (1) tHD;STAHS-mode CB=400pF; note 5min 160 ns22
LOW Period of SCL Clock tLOWFS-modemin 500 ns22
LOW Period of SCL Clock tLOWHS-mode CB=100pFmin 160 ns22
LOW Period of SCL Clock tLOWHS-mode CB=400pF; note 5min 320 ns22
HIGH Period of SCL Clock tHIGHFS-modemin 260 ns22
HIGH Period of SCL Clock tHIGHHS-mode CB=100pFmin 60 ns22
HIGH Period of SCL Clock tHIGHHS-mode CB=400pF; note 5min 120 ns22
Setup Time for a Repeated START condition tSU;STAFS-modemin 260 ns22
Setup Time for a Repeated START condition tSU;STAHS-mode CB=100pFmin 160 ns22
Setup Time for a Repeated START condition tSU;STAHS-mode CB=400pF; note 5min 160 ns22
Data Hold Time (2) tHD;DATFS-modemin 0 · max 450 ns22
Data Hold Time (2) tHD;DATHS-mode CB=100pFmin 0 · max 70 ns22
Data Hold Time (2) tHD;DATHS-mode CB=400pF; note 5min 0 · max 150 ns22
Data Setup Time (3) tSU;DATFS-modemin 50 ns22
Data Setup Time (3) tSU;DATHS-mode CB=100pFmin 10 ns22
Data Setup Time (3) tSU;DATHS-mode CB=400pF; note 5min 10 ns22
Rise Time of SDA and SCL Signals tRFS-mode; minimum 20+0.1Cb nsmax 120 ns22
Fall time of SDA and SCL signals tFFS-mode; minimum 20+0.1Cb ns; note 4max 120 ns23
Rise time of SCLH signal trCLHS-mode CB=100pF; Ext. pull-up source of 3mAmin 10 · max 40 ns23
Rise time of SCLH signal trCLHS-mode CB=400pF; Ext. pull-up source of 3mA; note 5min 20 · max 80 ns23
Rise time of SCLH signal after repeated START condition and after an acknowledge bit trCL1HS-mode CB=100pF; Ext. pull-up source of 3mAmin 10 · max 80 ns23
Rise time of SCLH signal after repeated START condition and after an acknowledge bit trCL1HS-mode CB=400pF; Ext. pull-up source of 3mA; note 5min 20 · max 160 ns23
Output rise time of SCLH signal tfCLHS-mode CB=100pF; Ext. pull-up source of 3mAmin 10 · max 40 ns23
Output rise time of SCLH signal tfCLHS-mode CB=400pF; Ext. pull-up source of 3mA; note 5min 20 · max 80 ns23
Output rise time of SDAH signal trDAHS-mode CB=100pFmin 10 · max 80 ns23
Output rise time of SDAH signal trDAHS-mode CB=400pF; note 5min 20 · max 160 ns23
Output rise time of SDAH signal tfDAHS-mode CB=100pFmin 10 · max 80 ns23
Output rise time of SDAH signal tfDAHS-mode CB=400pF; note 5min 20 · max 160 ns23
Setup Time for STOP Condition tSU;STOFS-modemin 260 ns23
Setup Time for STOP Condition tSU;STOHS-mode CB=100pFmin 160 ns23
Setup Time for STOP Condition tSU;STOHS-mode CB=400pF; note 5min 160 ns23

Pins, by the datasheet

14
1 SDA
Bidirectional I²C data pin with open drain output. · p. 5
2 SCL
I²C clock input with Schmitt trigger. · p. 5
3 A2
I²C address selection pin 3 with Schmitt trigger. · p. 5
4 A1
I²C address selection pin 4 with Schmitt trigger. · p. 5
5 TEST
Test pin; connect to GND. · p. 5
6 TEST
Test pin; leave open during normal operation. · p. 5
7 TEST
Test pin; leave open during normal operation. · p. 5
8 TEST
Test pin; leave open during normal operation. · p. 5
9 TEST
Test pin; leave open during normal operation. · p. 5
10 TEST
Test pin; leave open during normal operation. · p. 5
11 VDD5V
Positive supply voltage, 3.0 to 5.5 V. · p. 5
12 VDD3V
3.3V regulator output; connect to VDD for 3V supply and buffer to GND with 10uF in 5V operation. · p. 5
13 GND
Negative Supply Voltage (GND). · p. 5
14 PWM
Push-pull Pulse Width Modulation output. · p. 5

Open-source boards using it

2
  • 6 layers69.7 × 76.7 mmAmulet controller, the printed circuit board in 3D

    Amulet controller

    EPFLXplore/XRE_LeggedRobot_HW

    PCB designs for Xplore Research's robot dog project

    414 parts348Apache-2.0
  • 6 layers69.7 × 76.7 mmAmulet controller, the printed circuit board in 3D

    Amulet controller

    aidanbrzezinski/Prism-test

    ΛMULET is a high-power brushless motor controller, compatible with the moteus firmware. It was specifically designed to be integrated in EPFL Xplore's Legged Robot actuators.

    414 parts

Parts like it

8

Questions

Is there a KiCad symbol and footprint for the AS5048B-HTSP-500?

Yes. The symbol is Sensor_Magnetic:AS5048B and the footprint Package_SO:TSSOP-14_4.4x5mm_P0.65mm, both drawn on this page. PCBKit places them on a board for you when you design with it.

What package is the AS5048B-HTSP-500?

TSSOP-14, with 14 pins. Its footprint is drawn on this page.

Where is the AS5048B-HTSP-500 datasheet?

Advanced Monolithic Systems publishes it: the Datasheet link on this page opens it.

Where can I order the AS5048B-HTSP-500?

JLCPCB lists it as part C2655184, with 187 in stock; the sellers' links on this page open their listings.

What can replace the AS5048B-HTSP-500?

Parts like it in the library: the AS5047D-ATSM by Advanced Monolithic Systems, the AS5048A-HTSP-500 by Advanced Monolithic Systems, the A1333LLETR-T by Allegro MicroSystems, LLC and the A1335LLETR-T by Allegro MicroSystems, LLC. Check their datasheets: a part that fits the footprint may still differ in its ratings.

Which open-source boards use the AS5048B-HTSP-500?

2 boards in 2 repositories on GitHub; the most starred are listed on this page, with their KiCad files.