Skip to the content
1234567891011121314

AS5047P-ATSM

Advanced Monolithic SystemsExtended

-40℃~+125℃ 0°~360° 1.2mm 15mA 4.4mm 4.5V~5.5V 5mm Magnetic rotary position sensor No SPI TSSOP-14 Position Sensors ROHS

Part id
ams/AS5047P-ATSM
Category
Position Sensors
Package
TSSOP-14_4.4x5.0x0.65P
Pins
14
In stock
5,201 at JLCPCB (C962063)
Used on
34 open-source boards

Overview

The AS5047P-ATSM is a position Sensor made by Advanced Monolithic Systems in a TSSOP-14_4.4x5.0x0.65P package with 14 pins. -40℃~+125℃ 0°~360° 1.2mm 15mA 4.4mm 4.5V~5.5V 5mm Magnetic rotary position sensor No SPI TSSOP-14 Position Sensors ROHS.

PCBKit's library has its KiCad symbol (EasyEDA_Cloud:AS5047P-ATST, from EasyEDA) and its footprint (EasyEDA_Cloud:TSSOP-14_L5.0-W4.4-P0.65-LS6.4-BL, from EasyEDA), ready for a KiCad board. 5,201 are in stock at JLCPCB (part C962063). 34 open-source boards in 26 repositories on GitHub use it.

Symbol

1CSn2CLK3MISO4MOSI5Test6B7A8W/PWM9V10U11VDD12VDD3V313GND14I
EasyEDA_Cloud:AS5047P-ATSTFrom EasyEDA

Footprint

1234567891011121314
EasyEDA_Cloud:TSSOP-14_L5.0-W4.4-P0.65-LS6.4-BLFrom EasyEDA

From the datasheet

11
Supply, least
4.5 V · VDD, recommended operating min, 5.0V mode · p. 6
Supply, most
5.5 V · VDD, recommended operating max, 5.0V mode · p. 6
Supply, least
3 V · VDD3V3, recommended operating min, 3.3V mode · p. 6
Supply, most
3.6 V · VDD3V3, recommended operating max, 3.3V mode · p. 6
Supply, absolute maximum
7 V · VDD, absolute max · p. 5
Supply, absolute maximum
5 V · VDD3V3, absolute max · p. 5
Works from
-40 °C · Ambient temperature min, 5V operation · p. 5
Works up to
125 °C · Ambient temperature max, 5V operation · p. 5
Takes working
15 mA · Supply current max · p. 6
A pin gives at most
1 mA · Digital output current max, ABI and UVW · p. 6
A pin gives at most
4 mA · Digital output current max, MISO · p. 6

What it is and has

5
Maximum speed
28krpm · p. 1
Angle error compensation
DAEC™ Dynamic angle error compensation · p. 1
Core resolution
14-bit · p. 1
SPI
4-wire serial interface · p. 1
Diagnostics
Embedded self-diagnostics · p. 23

Around it

1
cap 1 μF
between VDD3V3 and GND; LDO decoupling capacitor; locate close to the chip. · p. 9

Specifications

40
ParameterConditionsAs printedPage
DC supply voltage at VDD pin VDD5min -0.3 · max 7 V5
DC supply voltage at VDD3V3 pin VDD3min -0.3 · max 5 V5
DC supply voltage at GND pin VSSmin -0.3 · max 0.3 V5
Input current (latch-up immunity) IscrAEC-Q100-004min -100 · max 100 mA5
Electrostatic discharge ESDAEC-Q100-002; minimum column states ±2min 2 kV5
Total power dissipation (all supplies and outputs) Ptmax 150 mW5
Ambient temperature 5V0 Ta5V0In the 5.0V power supply mode onlymin -40 · max 125 °C5
Ambient temperature 3V3 Ta3V3min -40 · max 125 °C5
Programming temperature TaProgProgramming @ room temperature (25°C ± 20°C)min 5 · max 45 °C5
Storage temperature Tstrgmin -55 · max 150 °C5
Package body temperature TbodyIPC/JEDEC J-STD-020max 260 °C5
Relative humidity non-condensing RHNCmin 5 · max 85 %5
Positive supply voltage VDD5.0V operation modemin 4.5 · typ 5 · max 5.5 V6
Positive supply voltage VDD3V33.3V operation mode; only from -40 to 125°Cmin 3 · typ 3.3 · max 3.6 V6
Positive supply voltage VDD_BurnSupply voltage required for programming in 3.3V operationmin 3.3 · max 3.5 V6
Regulated Voltage VREGVoltage at VDD3V3 pin if VDD ≠ VDD3V3min 3.2 · typ 3.4 · max 3.6 V6
Supply current IDDmax 15 mA6
Current on digital output (ABI, UVW) I_Outmax 1 mA6
Current on digital output MISO I_Out_MISOmax 4 mA6
Capacitive load on digital output C_Lmax 50 pf6
Orthogonal magnetic field strength, normal operating mode BzRequired orthogonal component of the magnetic field strength measured at the die's surface along a circle of 1.1mmmin 35 · max 70 mT7
Core resolution REStyp 14 bit7
Resolution of the ABI interface RES_ABIProgrammable with register setting (ABIRES)min 100 · max 4096 Steps per revolution7
Non-linearity, optimum placement of the magnet INLOPT @ 25°CMaximum stated as ±0.8max 0.8 degree7
Non-linearity optimum placement of the magnet over the full Temperature Range INLOPT+TEMPMaximum stated as ±1max 1 degree7
Non-linearity @ displacement of magnet and temperature -40°C to 150°C INLDIS+TEMPAssuming N35H Magnet (D=8mm, H=3mm) 500um displacement in x and y; z-distance @ 2000um; maximum stated as ±1.2max 1.2 degree7
RMS output noise (1 sigma). Not tested, guaranteed by design. ONLOrthogonal component for the magnetic field within the specified range (Bz)max 0.068 degree7
RMS output noise (1 sigma) on PWM interface ON_PWMOrthogonal component for the magnetic field within the specified range (Bz)max 0.068 degree7
System propagation delay –core tdelayReading angle via SPImin 90 · max 110 us7
System propagation delay after dynamic angle error correction. tdelay_DAECAt ABI and UVW interfacesmin 1.5 · max 1.9 us7
Sampling rate tsamplRefresh rate at SPImin 202 · typ 222 · max 247 ns8
Dynamic angle error DAE1700At 1700 RPM constant speedmax 0.02 degree8
Dynamic angle error DAEmaxAt 14500 RPM constant speedmax 0.18 degree8
Dynamic angle error at constant acceleration (25krad/s²) DAEacc25k radians/s² constant accelerationmax 0.175 degree8
Maximum speed MSmax 28000 RPM8
Power-on time tponTime frame between VDD > VDDmin and first valid angular value. Not tested, guaranteed by designmax 10 ms8
Programming temperature TaProgProgramming @ Room Temperature (25°C ±20°C)min 5 · max 45 °C26
Positive supply voltage VDD5 V operation mode. Supply voltage during programmingmin 4.5 · typ 5 · max 5.5 V26
Positive supply voltage VDD3.3 V operation mode. Supply voltage during programmingmin 3.3 · max 3.5 V26
Current for programming IProgMax current during OTP burn procedure.max 100 mA26

Pins, by the datasheet

14
1 CSn
SPI chip select, active low. · p. 3
2 CLK
SPI clock. · p. 3
3 MISO
SPI master data input, slave output. · p. 3
4 MOSI
SPI master data output, slave input. · p. 3
5 Test
Test pin; connect to ground. · p. 3
6 B
Incremental signal B. · p. 3
7 A
Incremental signal A. · p. 3
8 W/PWM
Commutation signal W or PWM. · p. 4
9 V
Commutation signal V. · p. 4
10 U
Commutation signal U. · p. 4
11 VDD
5V power supply voltage for on-chip regulator. · p. 4
12 VDD3V3
3.3V on-chip LDO output; requires an external 1uF decoupling capacitor. Used for the supply in 3.3V operation. · p. 4
13 GND
Ground. · p. 4
14 I
Incremental signal I (index) or PWM. · p. 4

Ordering codes, by the datasheet

2
AS5047P-ATST
TSSOP-14 · 13” Tape & Reel in dry pack, 4500 pcs/reel · p. 35
AS5047P-ATSM
TSSOP-14 · 7” Tape & Reel in dry pack, 500 pcs/reel · p. 35

Open-source boards using it

34See all 34
  • 6 layers69.7 × 76.7 mmAmulet controller, the printed circuit board in 3D

    Amulet controller

    EPFLXplore/XRE_LeggedRobot_HW

    PCB designs for Xplore Research's robot dog project

    414 parts348Apache-2.0
  • 6 layers56.7 × 54.7 mmBetter md80, the printed circuit board in 3D

    Better md80

    darshp848/bldc-controller-60v

    60 V, 20 A / 80 A peak BLDC motor controller that fits the MD80 v3.0 mounting. KiCad 10, 6 layers.

    144 parts1
  • 2 layers92.9 × 54.5 mmSaponseEx, the printed circuit board in 3D

    SaponseEx

    hide4096/SaponseEx

    91 parts1
  • 2 layers84 × 58 mmSmartKnobController ME507, the printed circuit board in 3D

    SmartKnobController ME507

    Larson-Nick/SmartKnobController

    This folder contains all mechanical and electrical design files for the Smart Knob Controller, created using KiCAD v9.0 and SolidWorks 2024.

    90 parts1
  • 2 layers18.4 × 9 mmEncoder BoardV2, the printed circuit board in 3D

    Encoder BoardV2

    polina4k/BIRD_PCB

    PCB for BIRD flapping wing drone

    13 parts1
  • 2 layers47.4 × 64 mmTORANEKO.Mk3, the printed circuit board in 3D

    TORANEKO.Mk3

    Tokoro0917/ToraNeko.Mk3

    KiCadプロジェクト本体(TORANEKO.Mk3.kicadpro / .kicadsch / .kicadpcb)を作成済みです(現状は空、これから回路図を起こしていきます)。 このディレクトリには、実際に回路図を起こす前に固めておいた機能ブロック構成・ペリフェラル割り当て案・BOMドラフトも一緒に置いています。

    93 parts1MIT
  • 6 layers69.7 × 76.7 mmAmulet controller, the printed circuit board in 3D

    Amulet controller

    aidanbrzezinski/Prism-test

    ΛMULET is a high-power brushless motor controller, compatible with the moteus firmware. It was specifically designed to be integrated in EPFL Xplore's Legged Robot actuators.

    414 parts

Parts like it

1

Questions

Is there a KiCad symbol and footprint for the AS5047P-ATSM?

Yes. The symbol is EasyEDA_Cloud:AS5047P-ATST and the footprint EasyEDA_Cloud:TSSOP-14_L5.0-W4.4-P0.65-LS6.4-BL, both drawn on this page. PCBKit places them on a board for you when you design with it.

What package is the AS5047P-ATSM?

TSSOP-14_4.4x5.0x0.65P, with 14 pins. Its footprint is drawn on this page.

Where is the AS5047P-ATSM datasheet?

Advanced Monolithic Systems publishes it: the Datasheet link on this page opens it.

Where can I order the AS5047P-ATSM?

JLCPCB lists it as part C962063, with 5,201 in stock; the sellers' links on this page open their listings.

What can replace the AS5047P-ATSM?

Parts like it in the library: the AS5147U-HTSM by Advanced Monolithic Systems. Check their datasheets: a part that fits the footprint may still differ in its ratings.

Which open-source boards use the AS5047P-ATSM?

34 boards in 26 repositories on GitHub; the most starred are listed on this page, with their KiCad files.