

Arduino Pro Mini
My arduino playground
- Size
- 17.8 × 33 mm
- Copper layers
- 2
- Thickness
- 1.6 mm
- Parts
- 29
- Nets
- 33
- Pads
- 108
- Tracks, vias
- 349, 29
- Pours
- 2
- Routed
- Yes
- KiCad
- KiCad 6 (file 20211014)
- Created
- 16 Feb 2022
- Updated
- 8 Mar 2024
Overview
Arduino Pro Mini is an open-source printed circuit board by zymaxcii, from the zymaxcii/sketch repository on GitHub. It is a 2-layer board of 17.8 × 33 mm with 29 parts on 33 nets, routed with 349 tracks and 29 vias.
It is built around the ATMEGA328-PU and MIC5205YM5. Its parts include 6 capacitors, 5 resistors, 2 ICs, 2 diodes and 1 transistor. It belongs with the AVR (ATmega, ATtiny) boards of this library.
Main components
2ATMEGA328-PU
PDIP-28-40℃~+85℃ 1.8V~5.5V 10bit 1KB 20MHz 23 2KB 32KB 8 Bit AVR Built-in FLASH PDIP-28 Microcontrollers (MCU/MPU/SOC) ROHSMicrochip TechnologyMicrocontrollers (MCU/MPU/SOC)MIC5205YM5
SOT-23-5-40℃~+125℃ 1 1.242V~15.65V 150mA 150uA 16V 350mV@(150mA) Adjustable Positive SOT-23-5 Voltage Regulators - Linear, Low Drop Out (LDO) Regulators ROHSMicrochip TechnologyVoltage Regulators - Linear, Low Drop Out (LDO) Regulators
README
cad/anavi-light-controller/anavi-light-controller-orig/README.mdANAVI Light Controller
ANAVI Light Controller is an open source hardware board for controlling 12V RGB LED strip powered by free and open source software. It features:
- Slot for RGB LED strip
- 12V input for the RGB LED strip
- Slots for up to 3 plug and play I2C sensors for temperature, barometric pressure, humidity and light
- UART (Universal asynchronous receiver/transmitter) pins for debugging
Open source software for ANAVI Light Controller written as an Arduino sketch is also available at GitHub.
License
The project is released under the Creative Commons Attribution-ShareAlike 4.0 International (CC BY-SA 4.0).
Note: This is a human-readable summary of (and not a substitute for) the license.
You are free to:
Share — copy and redistribute the material in any medium or format Adapt — remix, transform, and build upon the material for any purpose, even commercially. The licensor cannot revoke these freedoms as long as you follow the license terms. Under the following terms:
Attribution — You must give appropriate credit, provide a link to the license, and indicate if changes were made. You may do so in any reasonable manner, but not in any way that suggests the licensor endorses you or your use. ShareAlike — If you remix, transform, or build upon the material, you must distribute your contributions under the same license as the original. No additional restrictions — You may not apply legal terms or technological measures that legally restrict others from doing anything the license permits. Notices:
You do not have to comply with the license for elements of the material in the public domain or where your use is permitted by an applicable exception or limitation. No warranties are given. The license may not give you all of the permissions necessary for your intended use. For example, other rights such as publicity, privacy, or moral rights may limit how you use the material.
You will have to provide a link to the original creator of the project http://www.anavi.technology on any documentation or website.
Credit can be attributed through a link to the creator website: http://www.anavi.technology
Parts
29| Qty | Value | Footprint | References |
|---|---|---|---|
| 4 | 0.1uF | Arduino-Pro-Mini:0603-CAP | C1, C2, C3, C10 |
| 2 | Arduino-Pro-Mini:0603-RES | R1, R3 | |
| 2 | Arduino-Pro-Mini:1X02 | JP2, JP3 | |
| 2 | Arduino-Pro-Mini:1X12 | JP6, JP7 | |
| 2 | 10K | Arduino-Pro-Mini:0603-RES | R2, R11 |
| 2 | 10uF | Arduino-Pro-Mini:EIA3216 | C13, C19 |
| 2 | FIDUCIALUFIDUCIAL | Arduino-Pro-Mini:MICRO-FIDUCIAL | JP5, JP8 |
| 1 | Arduino-Pro-Mini:SJ_2S | SJ1 | |
| 1 | 330 | Arduino-Pro-Mini:0603-RES | R6 |
| 1 | 8/16/20MHz | Arduino-Pro-Mini:RESONATOR-SMD-1_1 | Q1 |
| 1 | ATMEGA328 | Arduino-Pro-Mini:TQFP32-08 | U1 |
| 1 | FRAME-LETTER | Arduino-Pro-Mini:CREATIVE_COMMONS | FRAME1 |
| 1 | FTDI Basic | Arduino-Pro-Mini:1X06 | JP1 |
| 1 | Green | Arduino-Pro-Mini:0603-LED-ALT1 | D3 |
| 1 | LOGO-SFENEW | Arduino-Pro-Mini:SFE-NEW-WEBLOGO | U$11 |
| 1 | LOGO-SFESK | Arduino-Pro-Mini:SFE-LOGO-FLAME | U$1 |
| 1 | MIC5205 | Arduino-Pro-Mini:SOT23-5 | U2 |
| 1 | OSHW-LOGOS | Arduino-Pro-Mini:OSHW-LOGO-S | U$3 |
| 1 | Red | Arduino-Pro-Mini:0603-LED-ALT1 | LED1 |
| 1 | Reset | Arduino-Pro-Mini:TACTILE-SWITCH-SMD-ALT01 | S1 |
More from zymaxcii/sketch
12- 2 layers70 × 50 mm

- 2 layers99.6 × 44.2 mm

- 2 layers74.9 × 40.6 mm

- 2 layers23.2 × 31.5 mm

- 2 layers43.8 × 158.8 mm

- 2 layers40.6 × 30.5 mm

- 16 layers30.4 × 24.1 mm

- 2 layers59.7 × 36.8 mm

- 2 layers61 × 25.4 mm

- 2 layers59.7 × 20 mm

- 2 layers28.4 × 15.2 mm

- 2 layers35.6 × 12.7 mm

Similar boards
- 2 layers20.6 × 30 mm

- 2 layers25.4 × 33 mm

- 2 layers18 × 33.2 mm

Arduino pro mini
etimou/arduino-pro-mini-kicad
This is a clone of the well known arduino board "pro-mini" designed in kicad while the original was designed in eagle. Ref https://store.arduino.cc/arduino-pro-mini
23 parts69 - 2 layers34.1 × 34.2 mm

TinyFINITY
fishpepper/tinyFINITY
Tiny and opensource video transmitter with integrated graphic OSD
155 parts42 - 2 layers139 × 139 mm

Breeze electronics design
microdynamics-robot-quadcopter/breeze_electronics_design
This project is created and managed by EDA softwares, which contains the breeze quadcopter's component library, footprint library, schematic, printed circuit boards, etc.
107 parts13GPL-3.0 - 2 layers66.8 × 104.8 mm

- 4 layers27.9 × 20.3 mm

RF Attenuator Board
ckflight/RF_ATTENUATOR_HARDWARE
1 to 6000MHz 7-Bit Digital Step Attenuator Board with Parallel or Serial Interface
35 parts5MIT - 4 layers70 × 50 mm

Questions
How big is the Arduino Pro Mini PCB?
It measures 17.8 × 33 mm and has 2 copper layers, 1.6 mm thick.
What parts does the Arduino Pro Mini use?
29 parts, built around the ATMEGA328-PU and MIC5205YM5. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the Arduino Pro Mini KiCad files?
From the zymaxcii/sketch repository on GitHub, at the commit this page was made from: the board is cad/Arduino-Pro-Mini/Arduino-Pro-Mini.kicad_pcb. PCBKit opens the board in the browser, with nothing to install.
Can I use the Arduino Pro Mini design in my own project?
Its repository states no licence, so its author keeps all rights: ask zymaxcii before reusing the design.