Skip to the content
2 layers53.3 × 15.2 mmMatrixctl, the printed circuit board in 3D

Visualizer for Covid-19 Exposure Notifications

Size
53.3 × 15.2 mm
Copper layers
2
Thickness
1.6 mm
Parts
24
Nets
30
Pads
134
Tracks, vias
246, 65
Pours
2
Routed
Yes
KiCad
KiCad 5 (file 20200921)
Created
23 Sep 2020
Updated
27 Sep 2020

Overview

Matrixctl is an open-source printed circuit board by znuh, from the znuh/exposure-notifications repository on GitHub. It is a 2-layer board of 53.3 × 15.2 mm with 24 parts on 30 nets, routed with 246 tracks and 65 vias.

It is built around the AP7313-33SRG and BAT60A. Its parts include 7 capacitors, 7 resistors, 4 connectors, 2 ICs and 1 diode.

Main components

2

README

README.md

Exposure Notifications

Printed Circuit Boards for the Covid-19 Exposure Notifications Visualizer - see this for more details

To remake Exposure Notifications you need to get/make four things:

  • a BBC micro:bit or Calliope Mini with the microbit-corona-scanner installed
  • a black 23x23cm RIBBA frame from IKEA
  • the printed circuit board for the LEDs - see the leds/ directory of this repository
  • the printed circuit board for the LED matrix controller - either matrixctl-v1 OR matrixctl-v2
    • matrixctl-v2 includes a socket for the micro:bit and a switching voltage regulator
    • matrixctl-v1 comes without a socket for the micro:bit and has no switching voltage regulator
    • v2 is more efficient and keeps the LED matrix driver cooler when more LEDs light up - therefore I recommend using v2

The printed circuit board designs are made with a Nightly Development Build of KiCAD. If you want to open/edit them you also need a recent Nightly Development Build. If you just want to use the PCBs unmodified you can also use the gerber-files from the gerber-subdirectories.

LED matrix board

The LED matrix board uses Würth 150141RV73100 LEDs. These are bicolor-LEDs but only the red LED is used. The landing pads for the LEDs have been reduced to a minimum to hide the pads underneath the LEDs. All PCB tracks are on the back side of the PCB. 1206 0-Ohms resistors are used instead of vias to cross tracks. LED matrix front side LED matrix back side

matrixctl v2 board

The part number of the micro:bit socket is PIS-1240. The Micro-USB connector is a Molex 105017-0001. You can get these parts and all additional components from digi-key.

Following a recommendation from the IS31FL3738 datasheet the board includes a Tantalum Capacitor to avoid audible noise produced by ceramics capacitors through the piezoelectric effect. Tantalum is a conflict resource. I've chosen a Kemet T495B336K010ATE450 because Kemet is a sane choice in general and their handling of the issue sounds ok. matrixctl v2 If you do not want to use the micro:bit socket you can also connect the micro:bit or a Calliope Mini to the pin header of the PCB. You need to connect I²C (SCL and SDA), 3V and GND.

Parts

24
QtyValueFootprintReferences
41uCapacitor_SMD:C_0603_1608MetricC102, C103, C104, C105
32.2kResistor_SMD:R_0603_1608MetricR103, R104, R112
22.2uCapacitor_SMD:C_0603_1608MetricC106, C107
2600R/1A/0.1Inductor_SMD:L_0805_2012MetricFB101, FB102
2Conn_02x05_Odd_EvenConnector_PinSocket_2.54mm:PinSocket_2x05_P2.54mm_VerticalJ101, J102
10Resistor_SMD:R_0603_1608MetricR106
1100kResistor_SMD:R_0603_1608MetricR101
120kResistor_SMD:R_0603_1608MetricR105
133u/10VCapacitor_Tantalum_SMD:CP_EIA-3528-21_Kemet-BC101
1AP7313-33SRPackage_TO_SOT_SMD:SOT-23U102
1BAT60ADiode_SMD:D_SOD-323D101
1Conn_01x08Connector_PinHeader_2.54mm:PinHeader_1x08_P2.54mm_VerticalJ103
1DNPResistor_SMD:R_0603_1608MetricR102
1IS31FL3738ledmatrix:QFN-28-1EP_5x5mm_P0.5mm_EP3.5x3.5mm_ThermalViasU101
1TestPointTestPoint:TestPoint_Pad_D1.0mmTP101
1USB_B_MicroConnector_USB:USB_Micro-B_Molex-105017-0001J104

More from znuh/exposure-notifications

2
  • 2 layers230 × 230 mmLeds, the printed circuit board in 3D

    Leds

    znuh/exposure-notifications

    Visualizer for Covid-19 Exposure Notifications

    35 parts
  • 2 layers66.8 × 29.7 mmMatrixctl, the printed circuit board in 3D

    Matrixctl

    znuh/exposure-notifications

    Visualizer for Covid-19 Exposure Notifications

    31 parts

Similar boards

  • 2 layers58 × 41 mmCo2mon, the printed circuit board in 3D

    Co2mon

    znuh/co2mon

    CO2 Multimon

    55 parts2
  • 2 layers90 × 150 mmEnc hid kicad v10, the printed circuit board in 3D

    Enc hid kicad v10

    znuh/kicad-frontpanel-generator

    Frontpanel Generator for KiCad PCBs

    98 parts2MIT
  • 2 layers17.8 × 43.2 mmStm32c0-nano, the printed circuit board in 3D

    Stm32c0-nano

    znuh/stm32c0-nano-hw

    STM32C0-Nano Board Hardware Design Files

    31 parts2CC-BY-SA-4.0
  • 4 layers100 × 83 mmModule17-Mainboard, the printed circuit board in 3D

    Module17-Mainboard

    M17-Project/Module_17

    M17 modem board for 9600-baud capable radios

    209 parts129CERN-OHL-W-2.0
  • 4 layers41.4 × 108 mmM17 3310, the printed circuit board in 3D

    M17 3310

    M17-Project/M17_3310

    Mainboard replacement for Nokia 3310

    124 parts68
  • 4 layers99.6 × 43.7 mmMini17, the printed circuit board in 3D

    Mini17

    M17-Project/Mini17

    Mini17 - QRP M17 handheld

    209 parts41
  • 4 layers132 × 84.5 mmHamodule, the printed circuit board in 3D

    Hamodule

    crgarcia12/electronics-homeassistant-lightscontroll

    A smart lighting controller PCB that integrates seamlessly with ESPHome and Home Assistant while maintaining full compatibility with traditional mechanical switches.

    207 parts28
  • 4 layers41.4 × 108 mmMesh3310, the printed circuit board in 3D

    Mesh3310

    JLTelectronics/The-Mesh3310-Project

    Make the worlds strongest Node

    223 parts26MIT

Questions

How big is the Matrixctl PCB?

It measures 53.3 × 15.2 mm and has 2 copper layers, 1.6 mm thick.

What parts does the Matrixctl use?

24 parts, built around the AP7313-33SRG and BAT60A. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the Matrixctl KiCad files?

From the znuh/exposure-notifications repository on GitHub, at the commit this page was made from: the board is matrixctl-v1/matrixctl.kicad_pcb and its schematic leds/leds.kicad_sch. PCBKit opens the board in the browser, with nothing to install.

Can I use the Matrixctl design in my own project?

Its repository states no licence, so its author keeps all rights: ask znuh before reusing the design.