Skip to the content
2 layers57.1 × 59.6 mmWalkieTalkie, the printed circuit board in 3D

Walky-Talky — LoRa voice communication system built on STM32 with a custom KiCad PCB. Features I2S digital mic input (INMP441), Codec2 voice compression (96kbps → 1.2kbps), RYLR998 LoRa RF at 915MHz, 12-bit DAC audio output, and FM-style channel selection via rotary encoder. All peripheral I/O driven by STM32 HAL DMA. Work in progress.

Size
57.1 × 59.6 mm
Copper layers
2
Thickness
1.6 mm
Parts
49
Nets
74
Pads
208
Tracks, vias
322, 16
Pours
1
Routed
Yes
KiCad
KiCad 9.0 (file 20241229)
Created
21 May 2026
Updated
27 May 2026

Overview

WalkieTalkie is an open-source printed circuit board by zmuhammad07, from the zmuhammad07/Walky_Talky repository on GitHub, published under the MIT licence. It is a 2-layer board of 57.1 × 59.6 mm with 49 parts on 74 nets, routed with 322 tracks and 16 vias.

It is built around the PAM8403DR and LM1117DT-ADJ. Its parts include 20 capacitors, 6 connectors, 5 resistors, 4 ICs and 2 switches. It belongs with the radio and wireless and audio and music boards and the STM32 boards of this library.

Main components

2

README

README.md

Walky-Talky

Walky-Talky is a custom STM32-based digital voice communication system built for long-range, low-bandwidth voice transmission over LoRa RF.

The project combines embedded firmware development, custom PCB design in KiCad, digital signal processing, and wireless communication into a fully self-contained handheld device.

Voice audio is captured using an INMP441 I2S microphone, compressed in real time using the Codec2 low-bitrate voice codec, and transmitted through a RYLR998 LoRa module operating at 915 MHz. On the receiving side, audio is decoded and played back through a 12-bit DAC and PAM8403 speaker amplifier.

To support continuous real-time streaming, STM32 DMA is used throughout both the audio and RF pipelines, minimizing CPU overhead while maintaining low-latency operation.

The hardware was designed entirely from scratch in KiCad and includes custom analog audio circuitry, rotary encoder channel selection, power regulation, and RF interfacing on a fully custom PCB.

Features -Real-time digital voice communication over LoRa -Codec2 low-bitrate voice compression -STM32 DMA-driven audio streaming -INMP441 I2S microphone input -12-bit DAC audio playback -PAM8403 speaker amplifier output -Rotary encoder channel selection -Fully custom KiCad PCB design -Embedded real-time firmware architecture

System Diagram

image

Hardware Overview

Schematic: image

PCB Renderings: WalkieTalkieRnder2 WalkieTalkie

Technologies Used STM32 KiCad LoRa / RYLR998 Codec2 I2S Audio DMA Streaming Embedded C Digital Signal Processing Custom PCB Design

Parts

49
QtyValueFootprintReferences
6100nCapacitor_SMD:C_0603_1608MetricC1, C2, C3, C4, C5, C10
41uCapacitor_SMD:C_0603_1608MetricC8, C9, C19, C20
4MountingHoleMountingHole:MountingHole_2.2mm_M2H1, H2, H3, H4
310uCapacitor_SMD:C_0603_1608MetricC6, C13, C18
3Conn_01x01_PinConnector_PinSocket_2.54mm:PinSocket_1x01_P2.54mm_HorizontalJ4, J5, J6
20.1uCapacitor_SMD:C_0603_1608MetricC16, C17
21kResistor_SMD:R_0603_1608MetricR4, R5
220pCapacitor_SMD:C_0603_1608MetricC11, C12
2Conn_01x04_PinConnector_PinHeader_2.54mm:PinHeader_1x04_P2.54mm_VerticalJ2, J3
1100kResistor_SMD:R_0603_1608MetricR3
1100uCapacitor_SMD:C_0603_1608MetricC14
110nCapacitor_SMD:C_0603_1608MetricC7
1120RInductor_SMD:L_0603_1608MetricFB1
12.2uCapacitor_SMD:C_0603_1608MetricC15
1240Resistor_SMD:R_0603_1608MetricR1
1390Resistor_SMD:R_0603_1608MetricR2
18MHzCrystal:Crystal_SMD_3225-4Pin_3.2x2.5mmY1
1KY-040Connector_PinHeader_2.54mm:PinHeader_1x05_P2.54mm_VerticalU4
1LM1117DT-ADJPackage_TO_SOT_SMD:TO-252-3_TabPin2U2
1PAM8403DPackage_SO:SOIC-16_3.9x9.9mm_P1.27mmU3
1RResistor_SMD:R_0603_1608Metric1k1
1R1Resistor_SMD:R_0603_1608Metric10k2
1R2Resistor_SMD:R_0603_1608Metric10k1
1REDLED_SMD:LED_0201_0603MetricD1
1STM32F446RETxPackage_QFP:LQFP-64_10x10mm_P0.5mmU1
1SW_PushButton_Switch_THT:SW_DIP_SPSTx01_Slide_6.7x4.1mm_W7.62mm_P2.54mm_LowProfileSW3
1SW_SPDTButton_Switch_SMD:SW_SPDT_PCM12SW1
1SpeakerConnector_PinHeader_2.54mm:PinHeader_1x02_P2.54mm_VerticalLS1
1USB_B_MicroConnector_USB:USB_Micro-B_Wuerth_629105150521J1
1~INMP441ACEZ-R7:MIC_INMP441ACEZ-R7M1

Similar boards

  • 2 layers118 × 70 mmPhotogateV2, the printed circuit board in 3D

    PhotogateV2

    MarcioBulla/PhotogateV2

    Second Version of Photogate

    66 parts1
  • 2 layers69 × 37.9 mmIntro to PCB, the printed circuit board in 3D

    Intro to PCB

    JBrannon48/ATmega328P_DevBoard

    45 parts
  • 2 layers79.5 × 46.5 mmIntro to PCB, the printed circuit board in 3D

    Intro to PCB

    maribelvasquez/IntrotoSOCET_pcb

    46 parts
  • 2 layers145 × 60 mmBT BAT CNTLR, the printed circuit board in 3D

    BT BAT CNTLR

    NateJ892/bluetooth-battery-system

    TODO: - Upsize regulator - Add USB protection IC - Increase Connector Current to 1.5A each for "Fast Charging"

    89 parts
  • 2 layers77 × 42.5 mmIntro to PCB, the printed circuit board in 3D

    Intro to PCB

    Seokjae-Kim/Intro-to-PCB

    Intro to PCB schematics

    45 parts
  • 2 layers88.3 × 97.8 mmStarter, the printed circuit board in 3D

    Starter

    L0czek/rakieta

    The starter board provides the ignition impulse to fire the engine. It includes an I2C IO expander and an 8-channel digital comparator to require a correct safety byte/address to be present before firing.

    45 parts
  • 2 layers316 × 119 mmTeensy Grovebox, the printed circuit board in 3D

    Teensy Grovebox

    jerry20091103/Teensy_Grovebox

    A portable synth and music multi-tool made with Teensy 4.1

    142 parts150MIT
  • 2 layers149.9 × 99.5 mmMegafrank, the printed circuit board in 3D

    Megafrank

    rh1tech/frank

    RP2350 Based Hardware Emulation Platform

    262 parts66GPL-3.0

Questions

How big is the WalkieTalkie PCB?

It measures 57.1 × 59.6 mm and has 2 copper layers, 1.6 mm thick.

What parts does the WalkieTalkie use?

49 parts, built around the PAM8403DR and LM1117DT-ADJ. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the WalkieTalkie KiCad files?

From the zmuhammad07/Walky_Talky repository on GitHub, at the commit this page was made from: the board is Hardware/WalkieTalkie.kicad_pcb and its schematic Hardware/WalkieTalkie.kicad_sch. PCBKit opens the board in the browser, with nothing to install.

Can I use the WalkieTalkie design in my own project?

Its repository publishes it under the MIT licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).